INFINITI QX56 2004 Factory Service Manual
QX56 2004
INFINITI
INFINITI
https://www.carmanualsonline.info/img/42/57034/w960_57034-0.png
INFINITI QX56 2004 Factory Service Manual
Trending: phone, reset, oil pressure, service reset, trunk release, height, Di-11
Page 1861 of 3371
EI-20
FRONT FENDER
Revision: August 20072004 QX56
FRONT FENDERPFP:63100
Removal and InstallationEIS002XB
1. Remove headlamp. Refer to LT- 3 3 , "Removal and Installation" .
2. Remove over fender. Refer to EI-21, "
OVER FENDER" .
3. Remove fender protector. Refer to EI-23, "
FENDER PROTECTOR" .
4. Remove hood stay. Refer to BL-12, "
HOOD" .
5. Remove front fender.
Installation is in the reverse order of removal.
WIIA0263E
Page 1862 of 3371

OVER FENDER
EI-21
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
OVER FENDERPFP:63810
Removal and InstallationEIS002ZX
REMOVAL
1. Remove screws from front and/or rear over fender.
CAUTION:
Never apply tack-paper adhesive remover to body panel surface finished with lacquer-based paints.
Original over fenders are affixed to body panel with double-faced adhesive tape.
2. Heat over fender to between 30° and 40°C (86° to 104°F) with a heat gun.
3. Raise end of over fender and cut away tape, release plastic clips and remove over fender. Remove all
traces of tape.
INSTALLATION
On vehicles coated with Hard Clear Coat, use double-faced 3M adhesive tape Product No, 4210 or equiv-
alent, after priming with 3M primer Product No. N200, C-100 or equivalent.
The repair parts are also affixed with double-faced adhesive tape.
To re-use existing over fender, clean all traces of double-faced tape from the over fender and apply new
double-faced tape to the over fender.
1. Clean the panel surface with isopropyl alcohol or equivalent to degrease the surface.
2. Heat the panel and double-faced tape surface to 30° to 40°C (86° to 104°F).
3. Remove the backing sheet from the tape surface.
4. Align the plastic clips on the back side of the front and/or rear over fender to the mounting grommets.
5. Press ends by hand and use a roller to apply 5 kg-f (11lbs-f) to press over fender surface to body panel.
CAUTION:
To secure contact, do not wash vehicle for 24 hours after installation.
1. Grommet 2. Front over fender 3. Plastic clip
4. Double-faced adhesive tape 5. Spring nut 6. Rear over fender
7. Double-faced adhesive tape
WIIA0268E
Page 1863 of 3371
EI-22
OVER FENDER
Revision: August 20072004 QX56
6. Secure front and/or rear over fender with screws.
Page 1864 of 3371
FENDER PROTECTOR
EI-23
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
FENDER PROTECTORPFP:63840
Removal and InstallationEIS002XC
FRONT
1. Remove screws.
2. Remove plastic clips.
3. Remove front fender protector.
4. Remove clips and spring nuts from fender protector.
Installation is in the reverse order of removal.
1. Fender protector LH 2. Plastic clip 3. Spring nut
4. Screw 5. Clip 6. Grommet
7. Spring nut - early production 8. Nut - late production
WIIA0740E
Page 1865 of 3371
EI-24
LICENSE LAMP FINISHER
Revision: August 20072004 QX56
LICENSE LAMP FINISHERPFP:84810
Removal and InstallationEIS00300
1. Remove back door trim. Refer to EI-41, "BACK DOOR TRIM" .
2. Disconnect electrical harnesses from connectors.
3. Remove harnesses with bulbs from license lamps.
4. Remove nuts and screws from license lamp finisher.
5. Release clips and remove license lamp finisher.
Installation is in the reverse order of removal.
1. Rubber seal 2. Plastic clip 3. Nut
4. License lamp finisher 5. License plate fastener 6. Screw
7. Fastener 8. Rubber seal
WIIA0270E
Page 1866 of 3371
RUNNING BOARDS
EI-25
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
RUNNING BOARDSPFP:96110
Removal and InstallationEIS002XD
1. Remove bolts and remove running board from running board brackets.
2. Remove nuts and remove step pad from running board.
3. Remove nuts and bolts and remove running board brackets.
4. Remove screws and remove front and rear mud guards.
Installation is in the reverse order of removal.
1. Running board bracket 2. Front mud guard LH 3. Running board
4. Step pad 5. Rear mud guard LH
WIIA0265E
Page 1867 of 3371
EI-26
REAR SPOILER
Revision: August 20072004 QX56
REAR SPOILERPFP:96030
Removal and InstallationEIS002XE
1. Remove back door trim. Refer to EI-41, "BACK DOOR TRIM" .
2. Disconnect harness to high-mount stop lamp.
3. Disconnect washer tube.
4. Remove nuts, release clips and remove rear air spoiler.
5. Remove nuts and remove high-mount stop lamp.
Installation is in the reverse order of removal.
1. Grommet 2. Plastic clip 3. Nut
4. Rear air spoiler 5. High-mount stop lamp
LIIA1328E
Page 1868 of 3371
ROOF RACK
EI-27
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
ROOF RACKPFP:73155
Removal and InstallationEIS002XF
1. Remove screws, raise tie down hooks and remove finisher covers.
2. Remove bolts and remove front crossbar and gasket.
3. Remove screws, raise tie down hooks and remove slide rail covers.
4. Remove sliding crossbar.
5. Remove bolts and remove slide rails.
Installation is in the reverse order of removal.
To install finisher covers and slide rail covers, rotate tie hooks to the 50 degrees up position and slip cover
over tie down. Press down until clip is engaged. Rotate tie down hook to the down position. Install screws.
1. Sliding crossbar 2. Finisher cover 3. Front crossbar
4. Gasket 5. Slide rail 6. Slide rail cover
LIIA1031E
Page 1869 of 3371
EI-28
DOOR OUTSIDE MOLDING
Revision: August 20072004 QX56
DOOR OUTSIDE MOLDINGPFP:82820
Removal and InstallationEIS002XG
FRONT DOOR OUTSIDE MOLDING
Removal and Installation
1. Open windows fully.
2. Remove door mirror. Refer to GW-100, "
Door Mirror Assembly" .
3. Remove molding.
Remove hole cover and remove screw.
Lift molding from rear side.
Disconnect clips from flange.
Installation is in the reverse order of removal.
LIIA1035E
Page 1870 of 3371

SIDE GUARD MOLDING
EI-29
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
SIDE GUARD MOLDINGPFP:76840
Removal and InstallationEIS002XH
REMOVAL
CAUTION:
Never apply tack-paper adhesive remover to body panel surface finished with lacquer-based paints.
Original side guard molding is affixed to body panel with double-faced adhesive tape and plastic clips.
1. Heat side guard molding to between 30° and 40°C (86° to 104°F) with a heat gun.
2. Raise end of side guard molding, cut away double-faced adhesive tape and release clips to remove side
guard molding.
Remove all traces of double-faced adhesive tape.
INSTALLATION
On vehicles coated with Hard Clear Coat, use double-faced 3M adhesive tape Product No. 4210 or equiv-
alent, after priming with 3M primer Product No. N200, C-100 or equivalent.
The repair parts are also affixed with double-faced adhesive tape.
To re-use existing side guard molding, clean all traces of double-faced adhesive tape from the side guard
molding and apply new double-faced adhesive tape to the side guard molding.
1. Clean the panel surface with isopropyl alcohol or equivalent to degrease the surface.
LIIA1436E
Trending: change time, Wheels, power steering fluid, jacking, engine overheat, tire pressure reset, hood open