camera INFINITI QX56 2004 Factory User Guide

REAR VIEW MONITOR
DI-87
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
10. CHECK REAR VIEW CAMERA SIGNAL
1. Connect rear view camera connector.
2. Turn ignition switch ON.
3. Shift A/T selector lever to R position.
4. Check voltage signal between rear view camera control unit har-
ness connector B73 terminal 10 (G) and ground.
OK or NG
OK >> GO TO 11.
NG >> Replace the rear view camera. Refer to DI-88, "
Removal and Installation of Rear View Camera" .
11 . CHECK COMPOSITE SIGNAL OPEN OR SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector and display
unit connector.
3. Check continuity between rear view camera control unit harness
connector B73 terminal 12 (W) and display unit harness connec-
tor M93 terminal 15 (W).
4. Check continuity between rear view camera control unit harness
connector B73 terminal 12 (W) and ground.
OK or NG
OK >> GO TO 12.
NG >> Repair harness or connector.
12. CHECK COMPOSITE SIGNAL GROUND CIRCUIT
1. Check continuity between rear view camera control unit harness
connector B73 terminal 11 and display unit harness connector
M93 terminal 4.
2. Check continuity between rear view camera control unit harness
connector B73 terminal 11 and ground.
OK or NG
OK >> GO TO 13.
NG >> Repair harness or connector.10 (G) - Ground:
SKIA5100E
SKIA4894E
Continuity should exist.
Continuity should not exist.
WKIA1825E
Continuity should exist.
Continuity should not exist.
WKIA1826E

DI-88
REAR VIEW MONITOR
Revision: August 20072004 QX56
13. CHECK REAR VIEW CAMERA CONTROL UNIT COMPOSITE SIGNAL
1. Connect rear view camera control unit connector and display
unit connector.
2. Turn ignition switch ON.
3. Check voltage signal between rear view camera control unit har-
ness connector B73 terminal 12 (W) and ground.
OK or NG
OK >> Replace the display unit. Refer to AV- 1 5 8 , "Removal and Installation of Display Unit" .
NG >> Replace the rear view camera control unit. Refer to DI-88, "
Removal and Installation of Rear View
Camera Control Unit" .
Removal and Installation of Rear View Camera Control UnitEKS007RE
REMOVAL
1. Remove luggage side finisher lower LH. Refer to EI-39, "LUG-
GAGE FLOOR TRIM" .
2. Remove screws (2), and remove rear view camera control unit.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation of Rear View CameraEKS007RF
REMOVAL
1. Remove back door lower finisher. Refer to EI-41, "BACK DOOR TRIM" .
2. Remove connector.
3. Remove screws (2), and remove rear view camera.
INSTALLATION
Installation is in the reverse order of removal.12 (W) - Ground:
WKIA1827E
SKIA4896E
LKIA0478E
LKIA0479E

CONSULT-II CHECKING SYSTEM
GI-37
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: August 20072004 QX56
CONSULT-II CHECKING SYSTEMPFP:00000
DescriptionEAS001SK

CONSULT-II is a hand-held type tester. When it is connected with a diagnostic connector equipped on the
vehicle side, it will communicate with the control unit equipped in the vehicle and then enable various
kinds of diagnostic tests.

Refer to "CONSULT-II Operator's Manual" for more information.
Function and System ApplicationEAS001SL
x: Applicable.
*1: IVIS (NATS) [INFINITI Vehicle Immobilizer System (Nissan Anti-Theft System)].
*2: This system is shown with IVIS (NATS) using program card AEN04A-1 or later.Diagnostic test
modeFunction
ENGINE
A/T
ALL MODE AWD/4WD
ICC
ABS
AIR BAG
IPDM E/R
BCM
AUTO DRIVE POS.
REARVIEW CAMERA
AIR LEVELIZER
IVIS (NATS)
*1
IVIS (NATS BCM OR S/ENT)
*1
Work supportThis mode enables a technician to adjust some
devices faster and more accurately by following the
indications on CONSULT-II.x - xxx - - xxxx - -
Self-diagnosticSelf-diagnostic can be performed quickly. -----x-------
Self-diagnos-
tic resultsSelf-diagnostic results can be read and erased
quickly.xxxxx - xxx - xxx
Trouble diag-
nostic recordCurrent self-diagnostic results and all trouble diagnos-
tic records previously stored can be read.----- x-------
Data monitor Input/Output data in the ECM can be read. xxxxx - x - xxx - -
Data monitor
(spec)Data monitor specification can be read. x------------
CAN diagno-
sis support
monitorThe communication condition of CAN communication
line can be read.xxxxx - xxx - - - -
Active testDiagnostic Test Mode in which CONSULT-II drives
some actuators apart from the ECMs and also shifts
some parameters in a specified range.x- - xx- x- xxx- -
Function testThis mode can show results of self-diagnosis of ECU
with either “OK” or “NG”. For engines, more practical
tests regarding sensors/switches and/or actuators are
available.xx - - xx - -- - -- -
DTC & SRT
confirmationThe results of SRT (System Readiness Test) and the
self-diagnosis status/result can be confirmed.x------------
DTC work sup-
portThe operating condition to confirm Diagnosis Trouble
Codes can be selected.xx-----------
ECM/ECU part
numberECM/ECU part number can be read. xxxxx - -xx xx - -
ECU discrimi-
nated No.Classification number of a replacement ECU can be
read to prevent an incorrect ECU from being installed.-----x-------
Configuration ECM checks its own NATS communication interface. -------x-----
PIN read
*2This mode shows the BCM-specific 5-digit code. ------------x
Control unit
initialization
*2All registered ignition key IDs in NATS components
can be initialized and new IDs can be registered.-----------x-