matic j INFINITI QX56 2004 Factory Owner's Manual

ON BOARD DIAGNOSTIC (OBD) SYSTEM
AT-39
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
ON BOARD DIAGNOSTIC (OBD) SYSTEMPFP:00028
IntroductionUCS002CM
The A/T system has two self-diagnostic systems.
The first is the emission-related on board diagnostic system (OBD-II) performed by the TCM in combination
with the ECM. The malfunction is indicated by the MIL (malfunction indicator lamp) and is stored as a DTC in
the ECM memory but not the TCM memory.
The second is the TCM original self-diagnosis indicated by the A/T CHECK indicator lamp. The malfunction is
stored in the TCM memory. The detected items are overlapped with OBD-II self-diagnostic items. For detail,
refer to AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE" .
OBD-II Function for A/T SystemUCS002C N
The ECM provides emission-related on board diagnostic (OBD-II) functions for the A/T system. One function
is to receive a signal from the TCM used with OBD-related parts of the A/T system. The signal is sent to the
ECM when a malfunction occurs in the corresponding OBD-related part. The other function is to indicate a
diagnostic result by means of the MIL (malfunction indicator lamp) on the instrument panel. Sensors, switches
and solenoid valves are used as sensing elements.
The MIL automatically illuminates in One or Two Trip Detection Logic when a malfunction is sensed in relation
to A/T system parts.
One or Two Trip Detection Logic of OBD-IIUCS002CO
ONE TRIP DETECTION LOGIC
If a malfunction is sensed during the first test drive, the MIL will illuminate and the malfunction will be stored in
the ECM memory as a DTC. The TCM is not provided with such a memory function.
TWO TRIP DETECTION LOGIC
When a malfunction is sensed during the first test drive, it is stored in the ECM memory as a 1st trip DTC
(diagnostic trouble code) or 1st trip freeze frame data. At this point, the MIL will not illuminate. — First Trip
If the same malfunction as that experienced during the first test drive is sensed during the second test drive,
the MIL will illuminate. — Second Trip
The “trip” in the “One or Two Trip Detection Logic” means a driving mode in which self-diagnosis is performed
during vehicle operation.
OBD-II Diagnostic Trouble Code (DTC)UCS002CP
HOW TO READ DTC AND 1ST TRIP DTC
DTC and 1st trip DTC can be read by the following methods.
( with CONSULT-II or GST) CONSULT-II or GST (Generic Scan Tool) Examples: P0705, P0720 etc.
These DTC are prescribed by SAE J2012.
(CONSULT-II also displays the malfunctioning component or system.)

1st trip DTC No. is the same as DTC No.

Output of the diagnostic trouble code indicates that the indicated circuit has a malfunction. How-
ever, in case of the Mode II and GST, they do not indicate whether the malfunction is still occurring
or occurred in the past and returned to normal.
CONSULT-II can identify them as shown below, therefore, CONSULT-II (if available) is recom-
mended.
A sample of CONSULT-II display for DTC and 1st trip DTC is shown
on the next page. DTC or 1st trip DTC of a malfunction is displayed
in SELF-DIAGNOSTIC RESULTS mode for “ENGINE” with CON-
SULT-II. Time data indicates how many times the vehicle was driven
after the last detection of a DTC.
BCIA0030E

TROUBLE DIAGNOSIS
AT-59
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
CAUTION:
Run the engine at idle for at least one minute.
Judgement of Stall Test
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value position
LINE PRESSURE TEST
Line Pressure Test Port
Line Pressure Test Procedure
1. Inspect the amount of engine oil and replenish if necessary.
2. Drive the car for about 10 minutes to warm it up so that the ATF reaches in range of 50 to 80°C (122 to
176°F), then inspect the amount of ATF and replenish if necessary.
NOTE:
The automatic fluid temperature rises in range of 50 to 80°C (122 to 176°F) during 10 minutes of
driving.Stall speed: 2,500 - 2,800 rpm
Selector lever position
Expected problem location
DR
Stall rotation HO

Forward brake

Forward one-way clutch

1st one-way clutch

3rd one-way clutch
OH

Reverse brake
LL

Engine and torque converter one-way clutch
HH

Line pressure low
Does not shift-up D position 1 → 2 Slipping in 2nd, 3rd, 4th gears Direct clutch slippage
Does not shift-up D position 2 → 3 Slipping in 3rd, 4th, 5th gears High & low reverse clutch slippage
Does not shift-up D position 3 → 4 Slipping in 4th, 5th gears Input clutch slippage
Does not shift-up D position 4 → 5 Slipping in 5th gear Front brake slippage
SCIA1291E

AT-134
DTC P1716 TURBINE REVOLUTION SENSOR
Revision: August 20072004 QX56
DTC P1716 TURBINE REVOLUTION SENSORPFP:31935
DescriptionUCS002FC
The turbine revolution sensor detects input shaft rpm (revolutions per minute). It is located on the input side of
the automatic transmission. Monitors revolution of sensor 1 and sensor 2 for non-standard conditions.
CONSULT-II Reference ValueUCS002FD
On Board Diagnosis LogicUCS002FE

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “TURBINE REV S/CIRC” with CONSULT-II or P1716 without CONSULT-II is
detected under the following conditions.
–When TCM does not receive the proper voltage signal from the sensor.
–When TCM detects an irregularity only at position of 4th gear for turbine revolution sensor 2.
Possible CauseUCS002FF

Harness or connectors
(The sensor circuit is open or shorted.)

Turbine revolution sensor 1, 2
DTC Confirmation ProcedureUCS002FG
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Start engine and maintain the following conditions for at least 5
consecutive seconds.
VHCL SPEED SE: 40 km/h (25 MPH) or more
ENGINE SPEED: 1,500 rpm or more
ACCELE POS: 0.5/8 or more
Selector lever: “D” position
Gear position (Turbine revolution sensor 1): 4th or 5th posi-
tion
Gear position (Turbine revolution sensor 2): All position
Driving location: Driving the vehicle uphill (increased
engine load) will help maintain the driving conditions required for this test.
4. If DTC is detected, go to AT-135, "
Diagnostic Procedure" .
WITH GST
Follow the procedure “With CONSULT-II”.
Item name Condition Display value (rpm)
TURBINE REV During driving (lock-up ON) Approximately matches the engine speed.
BCIA0030E

SERVICE DATA AND SPECIFICATIONS (SDS)
AT-331
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsUCS002J T
*1: Refer to MA-10, "Fluids and Lubricants" .
Vehicle Speed When Shifting GearsUCS002JU
NORMAL MODE

At half throttle, the accelerator opening is 4/8 of the full opening.
TOW MODE

At half throttle, the accelerator opening is 4/8 of the full opening. Applied model 4x2 4x4
Automatic transmission model RE5R05A
Transmission model code number 95X13 95X14
Stall torque ratio2.0: 1
Transmission gear ratio1st 3.827
2nd 2.368
3rd 1.519
4th 1.000
5th 0.834
Reverse 2.613
Recommended fluid NISSAN Matic Fluid J*1
Fluid capacity 10.6 liter (11-1/4 US qt, 9-3/8 Imp qt)
CAUTION:

Use only Genuine NISSAN ATF Matic Fluid J. Do not mix with other fluid.

Using automatic transmission fluid other than Genuine NISSAN an ATF Matic Fluid J will deteriorate in driveability and
automatic transmission durability, and may damage the automatic transmission, which is not covered by the warranty.
Final
gear
ratioThrottle positionVehicle speed km/h (MPH)
D
1 →D2D2 →D3D3 →D4D4 →D5D5 →D4D4 →D3D3 →D2D2 →D1
2.937Full throttle 70 - 74
(44 - 46)112 - 120
(70 - 75)176 - 186
(110 - 116)249 - 259
(155 - 161)245 - 255
(152 - 159)166 - 176
(103 - 110)100 - 108
(62 - 67)43 - 47
(27 - 30)
Half throttle 46 - 50
(28 - 31)74 - 82
(46 - 51)103 - 113
(64 - 70)135 - 145
(84 - 90)109 - 119
(68 - 74)69 - 79
(43 - 49)44 - 52
(27 - 32)11 - 1 5
(7 - 10)
3.357Full throttle 61 - 65
(38 - 41)97 - 105
(61 - 66)153 - 163
(95 - 102)236 - 246
(147 - 153)232 - 242
(144 - 151)143 - 153
(89 - 95)87 - 95
(54 - 59)43 - 47
(27 - 29)
Half throttle 41 - 45
(26 - 28)66 - 74
(41 - 46)89 - 99
(56 - 62)117 - 127
(73 - 79)95 - 105
(59 - 65)59 - 69
(37 - 43)38 - 46
(24 - 29)11 - 1 5
(7 - 10)
Final
gear
ratioThrottle positionVehicle speed km/h (MPH)
D
1 →D2D2 →D3D3 →D4D4 →D5D5 →D4D4 →D3D3 →D2D2 →D1
2.937Full throttle 70 - 74
(44 - 46)112 - 120
(70 - 75)176 - 186
(110 - 116)249 - 259
(155 - 161)245 - 255
(152 - 159)166 - 176
(103 - 110)100 - 108
(62 - 67)43 - 47
(27 - 30)
Half throttle 50 - 54
(31 - 34)81 - 89
(50 - 55)113 - 123
(70 - 76)135 - 145
(84 - 90)109 - 119
(68 - 74)68 - 78
(42 - 48)44 - 52
(27 - 32)11 - 1 5
(7 - 10)
3.357Full throttle 61 - 65
(38 - 41)97 - 105
(61 - 66)153 - 163
(95 - 102)236 - 246
(147 - 153)232 - 242
(144 - 151)143 - 153
(89 - 95)87 - 95
(54 - 59)43 - 47
(27 - 29)
Half throttle 43 - 47
(27 - 29)72 - 80
(45 - 50)98 - 108
(61 - 67)117 - 127
(73 - 79)95 - 105
(59 - 65)59 - 69
(37 - 43)37 - 45
(23 - 28)11 - 1 5
(7 - 10)

ATC-1
AUTOMATIC AIR CONDITIONER
J AIR CONDITIONER
CONTENTS
C
D
E
F
G
H
I
K
L
M
SECTION AT C
A
B
AT C
Revision: August 20072004 QX56 PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 5
Precautions for Working with HFC-134a (R-134a) ..... 5
Contaminated Refrigerant ........................................ 5
General Refrigerant Precautions .............................. 6
Precautions for Leak Detection Dye ......................... 6
A/C Identification Label ............................................ 7
Precautions for Refrigerant Connection ................... 7
FEATURES OF NEW TYPE REFRIGERANT
CONNECTION ...................................................... 7
O-RING AND REFRIGERANT CONNECTION ..... 8
Precautions for Servicing Compressor ....................11
Precautions for Service Equipment .........................11
RECOVERY/RECYCLING EQUIPMENT .............11
ELECTRONIC LEAK DETECTOR .......................11
VACUUM PUMP ................................................. 12
MANIFOLD GAUGE SET .................................... 12
SERVICE HOSES ............................................... 12
SERVICE COUPLERS ........................................ 13
REFRIGERANT WEIGHT SCALE ...................... 13
CHARGING CYLINDER ...................................... 13
Wiring Diagrams and Trouble Diagnosis ................ 13
PREPARATION ......................................................... 14
Special Service Tools ............................................. 14
HFC-134a (R-134a) Service Tools and Equipment ... 14
Commercial Service Tools ...................................... 17
REFRIGERATION SYSTEM ..................................... 18
Refrigerant Cycle ................................................... 18
REFRIGERANT FLOW ....................................... 18
Refrigerant System Protection ............................... 18
REFRIGERANT PRESSURE SENSOR ............. 18
PRESSURE RELIEF VALVE .............................. 19
Component Layout ................................................. 20
FRONT REFRIGERATION SYSTEM .................. 20
REAR REFRIGERATION SYSTEM .................... 21LUBRICANT .............................................................. 22
Maintenance of Lubricant Quantity in Compressor ... 22
LUBRICANT ........................................................ 22
CHECKING AND ADJUSTING ............................ 22
AIR CONDITIONER CONTROL ............................... 24
Description .............................................................. 24
Operation ................................................................ 24
AIR MIX DOORS CONTROL .............................. 24
FAN SPEED CONTROL ...................................... 24
INTAKE DOOR CONTROL ................................. 24
MODE DOOR CONTROL ................................... 24
DEFROSTER DOOR CONTROL ........................ 24
MAGNET CLUTCH CONTROL ........................... 25
SELF-DIAGNOSTIC SYSTEM ............................ 25
Description of Control System ................................ 26
Control Operation ................................................... 26
DISPLAY SCREEN .............................................. 27
AUTO SWITCH ................................................... 27
TEMPERATURE DIAL (DRIVER) ........................ 27
TEMPERATURE DIAL (PASSENGER) ............... 27
RECIRCULATION SWITCH () ............................. 27
DEFROSTER () SWITCH .................................... 27
REAR WINDOW DEFOGGER SWITCH ............. 27
OFF SWITCH (HOLD FAN DOWN SWITCH
UNTIL SYSTEM SHUTS OFF) ............................ 27
A/C SWITCH ....................................................... 27
MODE SWITCH .................................................. 27
FRONT FAN SWITCH ......................................... 27
REAR FAN SWITCH (FRONT) ............................ 27
REAR TEMPERATURE/MODE DIAL (FRONT) ... 27
REAR TEMPERATURE/MODE DIAL (REAR) .... 28
REAR FAN CONTROL SWITCH (REAR) ........... 28
Discharge Air Flow ................................................. 29
FRONT ................................................................ 29
REAR .................................................................. 29
System Description (Front) ..................................... 30
CONTROLS AND THEIR FUNCTIONS .............. 30
System Description (Rear) ..................................... 31
CONTROLS AND THEIR FUNCTIONS .............. 31
CAN Communication System Description .............. 32

ATC-2Revision: August 20072004 QX56 TROUBLE DIAGNOSIS ............................................ 33
CONSULT-II Function (BCM) .................................. 33
CONSULT-II BASIC OPERATION ....................... 33
DATA MONITOR .................................................. 34
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 35
WORK FLOW ...................................................... 35
SYMPTOM TABLE .............................................. 35
Component Parts and Harness Connector Location ... 37
ENGINE COMPARTMENT .................................. 37
FRONT PASSENGER COMPARTMENT ............ 38
REAR PASSENGER COMPARTMENT ............... 39
Schematic ............................................................... 40
Wiring Diagram — A/C,A — ................................... 41
Front Air Control Terminals and Reference Value ... 51
PIN CONNECTOR TERMINAL LAYOUT ............ 51
TERMINALS AND REFERENCE VALUE FOR
FRONT AIR CONTROL ....................................... 51
A/C System Self-diagnosis Function ...................... 53
DESCRIPTION .................................................... 53
Operational Check (Front) ...................................... 56
CHECKING MEMORY FUNCTION ..................... 56
CHECKING BLOWER ......................................... 56
CHECKING DISCHARGE AIR ............................ 57
CHECKING RECIRCULATION ............................ 57
CHECKING TEMPERATURE DECREASE ......... 57
CHECKING TEMPERATURE INCREASE .......... 58
CHECK A/C SWITCH .......................................... 58
CHECKING AUTO MODE ................................... 58
Operational Check (Rear) ....................................... 59
CHECKING BLOWER ......................................... 59
CHECKING TEMPERATURE DECREASE ......... 59
CHECKING TEMPERATURE INCREASE .......... 59
Power Supply and Ground Circuit for Front Air Con-
trol ........................................................................... 60
INSPECTION FLOW ........................................... 60
COMPONENT DESCRIPTION ............................ 61
DIAGNOSTIC PROCEDURE FOR A/C SYSTEM ... 61
Mode Door Motor Circuit ........................................ 63
INSPECTION FLOW ........................................... 63
SYSTEM DESCRIPTION .................................... 64
COMPONENT DESCRIPTION ............................ 65
DIAGNOSTIC PROCEDURE FOR MODE
DOOR MOTOR ................................................... 65
Air Mix Door Motor Circuit ...................................... 67
INSPECTION FLOW ........................................... 67
SYSTEM DESCRIPTION .................................... 68
COMPONENT DESCRIPTION ............................ 69
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (DRIVER) ................................... 69
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (PASSENGER) .......................... 71
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (REAR) ...................................... 73
Intake Door Motor Circuit ........................................ 76
INSPECTION FLOW ........................................... 76
SYSTEM DESCRIPTION .................................... 77
COMPONENT DESCRIPTION ............................ 78
DIAGNOSTIC PROCEDURE FOR INTAKE DOOR MOTOR ....................................................78
Defroster Door Motor Circuit ...................................79
SYMPTOM: ..........................................................79
INSPECTION FLOW ............................................79
SYSTEM DESCRIPTION .....................................80
COMPONENT DESCRIPTION ............................80
DIAGNOSTIC PROCEDURE FOR
DEFROSTER DOOR MOTOR .............................81
Front Blower Motor Circuit ......................................83
INSPECTION FLOW ............................................83
SYSTEM DESCRIPTION .....................................84
COMPONENT DESCRIPTION ............................85
DIAGNOSTIC PROCEDURE FOR BLOWER
MOTOR ................................................................85
COMPONENT INSPECTION ...............................89
Rear Blower Motor Circuit .......................................90
INSPECTION FLOW ............................................90
SYSTEM DESCRIPTION .....................................91
DIAGNOSTIC PROCEDURE FOR REAR
BLOWER MOTOR ...............................................91
COMPONENT INSPECTION ...............................99
Rear Air Control Circuit ......................................... 101
INSPECTION FLOW .......................................... 101
SYSTEM DESCRIPTION ................................... 102
DIAGNOSTIC PROCEDURE FOR REAR AIR
CONTROL ......................................................... 102
Magnet Clutch Circuit ............................................ 104
INSPECTION FLOW .......................................... 104
SYSTEM DESCRIPTION ................................... 105
DIAGNOSTIC PROCEDURE FOR MAGNET
CLUTCH ............................................................ 105
Insufficient Cooling ................................................110
INSPECTION FLOW ..........................................110
PERFORMANCE TEST DIAGNOSES .............. 111
PERFORMANCE CHART ..................................113
TROUBLE DIAGNOSES FOR UNUSUAL PRES-
SURE .................................................................114
Insufficient Heating ...............................................117
INSPECTION FLOW ..........................................117
Noise .....................................................................118
INSPECTION FLOW ..........................................118
Self-diagnosis ....................................................... 120
INSPECTION FLOW .......................................... 120
Memory Function .................................................. 121
INSPECTION FLOW .......................................... 121
Water Valve Circuit ................................................ 121
COMPONENT DESCRIPTION .......................... 121
DIAGNOSTIC PROCEDURE FOR WATER
VALVE ................................................................ 122
COMPONENT INSPECTION ............................. 124
Ambient Sensor Circuit ......................................... 125
COMPONENT DESCRIPTION .......................... 125
AMBIENT TEMPERATURE INPUT PROCESS . 125
DIAGNOSTIC PROCEDURE FOR AMBIENT
SENSOR ............................................................ 125
COMPONENT INSPECTION ............................. 127
In-vehicle Sensor Circuit ....................................... 128
COMPONENT DESCRIPTION .......................... 128
DIAGNOSTIC PROCEDURE FOR IN-VEHICLE

ATC-12
PRECAUTIONS
Revision: August 20072004 QX56
VACUUM PUMP
The lubricant contained inside the vacuum pump is not compatible
with the specified lubricant for HFC-134a (R-134a) A/C systems.
The vent side of the vacuum pump is exposed to atmospheric pres-
sure so the vacuum pump lubricant may migrate out of the pump into
the service hose. This is possible when the pump is switched off
after evacuation (vacuuming) and hose is connected to it.
To prevent this migration, use a manual valve situated near the
hose-to-pump connection, as follows.

Usually vacuum pumps have a manual isolator valve as part of
the pump. Close this valve to isolate the service hose from the
pump.

For pumps without an isolator, use a hose equipped with a man-
ual shut-off valve near the pump end. Close the valve to isolate
the hose from the pump.

If the hose has an automatic shut off valve, disconnect the hose
from the pump: as long as the hose is connected, the valve is
open and lubricating oil may migrate.
Some one-way valves open when vacuum is applied and close
under a no vacuum condition. Such valves may restrict the pump's
ability to pull a deep vacuum and are not recommended.
MANIFOLD GAUGE SET
Be certain that the gauge face indicates HFC-134a (R-134a or
134a). Make sure the gauge set has 1/2″-16 ACME threaded con-
nections for service hoses. Confirm the set has been used only with
refrigerant HFC-134a (R-134a) along with specified lubricant.
SERVICE HOSES
Be certain that the service hoses display the markings described
(colored hose with black stripe). All hoses must include positive shut-
off devices (either manual or automatic) near the end of the hoses
opposite the manifold gauge.
RHA270D
SHA5 33 D
RHA272D

REFRIGERATION SYSTEM
ATC-19
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
PRESSURE RELIEF VALVE
The refrigerant system is also protected by a pressure relief valve, located in the rear head of the compressor.
When the pressure of refrigerant in the system increases to an abnormal level [more than 2,990 kPa (30.5 kg/
cm
2 , 433.6 psi)], the release port on the pressure relief valve automatically opens and releases refrigerant
into the atmosphere.
WJIA1342E

ATC-24
AIR CONDITIONER CONTROL
Revision: August 20072004 QX56
AIR CONDITIONER CONTROLPFP:27500
DescriptionEJS002BW
The front air control provides automatic regulation of the vehicle's interior temperature. The system is based
on the driver's and passenger's selected "set temperature", regardless of the outside temperature changes.
This is done by utilizing a microcomputer that is part of the front air control, which receives input signals from
the following five sensors:

Ambient sensor

In-vehicle sensor

Intake sensor

Optical sensor (one sensor for driver and passenger side)

PBR (position balanced resistor)
The front air control uses these signals (including the set temperature) to automatically control:

Outlet air volume

Air temperature

Air distribution
The front air control also provides separate regulation of the vehicle's interior temperature for the rear passen-
ger area. The system is based on the temperature and rear blower settings selected on the front air control
rear fan switch (front) and rear temperature/mode dial (front), or from the rear fan switch (rear) and rear tem-
perature/mode dial (rear) on the rear air control, when the rear fan switch (front) is set to the rear (R) position.
The front air control or rear air control is used to select:

Outlet air volume

Air temperature/mode distribution
OperationEJS002BX
AIR MIX DOORS CONTROL
The air mix doors are automatically controlled so that in-vehicle temperature is maintained at a predetermined
value by the temperature setting, ambient temperature, in-vehicle temperature and amount of sunload.
FAN SPEED CONTROL
Blower speed is automatically controlled based on temperature setting, ambient temperature, in-vehicle tem-
perature, intake temperature, amount of sunload and air mix door position.
When AUTO switch is pressed, the blower motor starts to gradually increase air flow volume (if required).
When engine coolant temperature is low, the blower motor operation is delayed to prevent cool air from flow-
ing.
INTAKE DOOR CONTROL
The intake door is automatically controlled by the temperature setting, ambient temperature, in-vehicle tem-
perature, intake temperature, amount of sunload and ON-OFF operation of the compressor.
MODE DOOR CONTROL
The mode door is automatically controlled by the temperature setting, ambient temperature, in-vehicle temper-
ature, intake temperature and amount of sunload.
DEFROSTER DOOR CONTROL
The defroster door is controlled by turning the defroster dial to front defroster.

AIR CONDITIONER CONTROL
ATC-27
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
DISPLAY SCREEN
Displays the operational status of the system.
AUTO SWITCH

The compressor, intake door, air mix doors, outlet doors and blower speed are automatically controlled so
that the in-vehicle temperature will reach, and be maintained at the set temperature selected by the oper-
ator.
TEMPERATURE DIAL (DRIVER)
Increases or decreases the driver zone temperature.
TEMPERATURE DIAL (PASSENGER)
Increases or decreases the passenger zone temperature.
RECIRCULATION SWITCH ()

When pressed an indicator turns ON in the display, and air inlet is set to recirculation mode.

Recirculation mode is cancelled by pressing the switch again, turning ON the front defroster, pressing the
OFF switch, or pressing the A/C switch to turn off the A/C system and compressor.
DEFROSTER () SWITCH
Positions the air outlet doors to the defrost position. Also positions the intake door to the outside air position.
REAR WINDOW DEFOGGER SWITCH
When switch is ON, rear window is defogged.
OFF SWITCH (HOLD FAN DOWN SWITCH UNTIL SYSTEM SHUTS OFF)
The compressor and blower are OFF, the intake door is set to the outside air position, and the air outlet doors
are set to the foot (75% foot and 25% defrost) position.
A/C SWITCH
The compressor is ON or OFF.
(Pressing the A/C switch when the AUTO switch is ON will turn off the A/C switch and compressor.)
MODE SWITCH
Controls the air discharge outlets.
FRONT FAN SWITCH
Manually controls the blower speed. Seven speeds are available for manual control (as shown on the display
screen).
REAR FAN SWITCH (FRONT)
Manually controls the rear blower speed. Four speeds are available for manual control. When the rear fan
switch (front) is in the off (0) position, the rear blower motor cannot operate. Position (R) allows control of rear
blower speed and rear temperature/mode operation to be transferred to rear air control.
REAR TEMPERATURE/MODE DIAL (FRONT)
Increases or decreases the rear zone temperature and adjusts the mode simultaneously. FLOOR is full hot
setting, FLOOR/PANEL is warm setting, and PANEL is full cold setting.