INFINITI QX56 2004 Factory Service Manual

TF-96
TROUBLE DIAGNOSES FOR SYMPTOMS
Revision: August 20072004 QX56
TRANSFER DROPPING RESISTOR
Check resistance between terminals.
ATP SWITCH, NEUTRAL-4LO SWITCH AND WAIT DETECTION SWITCH
1. Remove the ATP switch, neutral-4LO switch and the wait detection switch.
2. Measure the resistance between terminals of ATP switch F55, neutral-4LO switch F60 , and wait detection
switch F59.
TRANSFER MOTOR
Apply battery voltage directly to transfer motor harness connector
F57. (Positive: Terminal 14, Negative: Terminal 15)
Transfer motor should operate.
WDIA0091E
Resistance : 11.2 - 12.8 Ω
Switch released state : Continuity should not
exist
Switch pushed state : Continuity should exist
WDIA0082E
LDIA0097E

TROUBLE DIAGNOSES FOR SYMPTOMS
TF-97
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
TRANSFER MOTOR RELAY
1. Apply battery voltage and ground directly to transfer motor relay
E154 terminals 1 and 2.
2. Check continuity between transfer motor relay E153 terminals 3
and 5.
TRANSFER SHIFT RELAY (HIGH & LOW)
Check continuity between transfer shift high relay E46 and low relay
E47 terminals 3 and 4.
ACTUATOR AND ACTUATOR POSITION SWITCH
Actuator
Operation and resistance check

Apply battery voltage directly to actuator assembly.
Actuator Position Switch
Continuity check
Condition Continuity (3-5)
Battery voltage is applied Yes
No voltage is applied No
LDIA0098E
Condition Continuity
12V direct current supply
between terminals 1 and 2No
No current supply Yes
LDIA0099E
Operating check Battery positive terminal Battery negative terminal
121 24
224 21
Check Approx. 0.2Ω (When the motor is not operated.)
LDIA0100E
Continuity checkBattery positive
terminalBattery negative
terminalContinuity
121 24 20 - 22
224 21 23 - 22
LDIA0101E

TF-98
TRANSFER CONTROL UNIT
Revision: August 20072004 QX56
TRANSFER CONTROL UNITPFP:33084
Removal and InstallationEDS00314
REMOVAL
1. Set transfer state as 2WD when 4WD shift switch is at 2WD, or as AUTO when 4WD shift switch is at
AUTO.
CAUTION:
When removing transfer control unit, transfer state must be at 2WD or AUTO.
2. Turn the ignition switch OFF and disconnect negative battery terminal.
3. Remove the glove box assembly. Refer to IP-14, "
Instrument Lower Cover RH and Glove Box" .
4. Disconnect the two transfer control unit connectors.
5. Remove the transfer control unit bolts.
6. Remove the transfer control unit.
INSTALLATION
Installation is in the reverse order of removal.

When installing the transfer control unit, tighten bolts to the specified torque.
CAUTION:

Do not connect harness connector to transfer control unit when 4WD shift switch is at 4LO.

After the installation, check perform self-diagnosis. Refer to TF-28, "SELF-DIAGNOSTIC PROCEDURE"
. If NG, adjust position between transfer assembly and transfer control unit.
BDIA0014E
Transfer control unit bolts : 5.1 N·m (0.52 kg-m, 45 in-lb)

FRONT OIL SEAL
TF-99
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
FRONT OIL SEALPFP:38189
Removal and InstallationEDS00315
REMOVAL
1. Partially drain the transfer fluid. Refer to MA-24, "Changing Transfer Fluid" .
2. Remove the front propeller shaft. Refer to PR-4, "
Removal and Installation" .
3. Remove the companion flange self-lock nut, using Tool.
4. Put a matching mark on top of the front drive shaft in line with
the mark on the companion flange.
CAUTION:
Use paint to make the matching mark on the front drive
shaft. Do not damage the front drive shaft.
5. Remove the companion flange, using suitable tool.
6. Remove the oil seal from the front case, using Tool.
CAUTION:
Do not damage front case.Tool number : KV40104000 ( — )
SDIA2657E
SDIA2658E
WDIA0193E
Tool number : ST33290001 (J-34286)
LDIA0144E

TF-100
FRONT OIL SEAL
Revision: August 20072004 QX56
INSTALLATION
1. Install the oil seal until it is flush with the end face of the front
case, using Tool.
CAUTION:

Do not reuse oil seal.

Apply petroleum jelly to oil seal.
2. Align the matching mark of the front drive shaft with the match-
ing mark of the companion flange, then install the companion
flange.
3. Install the self-lock nut. Tighten to the specified torque, using
Tool. Refer to TF-110, "
Transfer Components" .
CAUTION:
Do not reuse self-lock nut.
4. Install the front propeller shaft. Refer to PR-4, "
Removal and
Installation" .
5. Refill the transfer with fluid and check fluid level. Refer to MA-
24, "Changing Transfer Fluid" .
6. Check the transfer for fluid leakage. Refer to MA-24, "
Checking
Transfer Fluid" . Tool number : KV38100500 ( — )
SDIA2662E
SDIA2658E
Tool number : KV40104000 ( — )
LDIA0147E

REAR OIL SEAL
TF-101
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
REAR OIL SEALPFP:33140
Removal and InstallationEDS00316
REMOVAL
1. Partially drain the transfer fluid. Refer to MA-24, "Changing Transfer Fluid" .
2. Remove the rear propeller shaft. Refer to PR-8, "
Removal and Installation" .
3. Remove the dust cover from the rear case.
CAUTION:
Do not damage the rear case.
4. Remove the rear oil seal from the rear case, using Tool.
CAUTION:
Do not damage the rear case.
INSTALLATION
1. Install the oil seal until it is flush with the end face of the rear
case, using Tool.
CAUTION:

Do not reuse oil seal.

Apply petroleum jelly to oil seal.
2. Apply petroleum jelly to the circumference of the new dust cover.
Position the dust cover using the identification mark as shown.
CAUTION:

Do not reuse dust cover.

Position the identification mark at the position shown.
WDIA0127E
Tool number : ST33290001 (J-34286)
LDIA0139E
Tool number : ST30720000 (J-25405)
LDIA0140E
SDIA2208E

TF-102
REAR OIL SEAL
Revision: August 20072004 QX56
3. Install the dust cover to the rear case, using Tool.
CAUTION:

Do not reuse dust cover.

Apply petroleum jelly to dust cover.
4. Install the rear propeller shaft. Refer to PR-8, "
Removal and
Installation" .
5. Refill the transfer with fluid and check fluid level. Refer to MA-
24, "Changing Transfer Fluid" .
6. Check the transfer for fluid leakage. Refer to MA-24, "
Checking
Transfer Fluid" . Tool number : KV40105310 ( — )
PDIA0 116 E

SIDE OIL SEAL
TF-103
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
SIDE OIL SEALPFP:33142
Removal and InstallationEDS00317
REMOVAL
1. Remove the front propeller shaft. Refer to PR-4, "Removal and Installation" .
2. Remove the companion flange. Refer to TF-99, "
Removal and Installation" .
3. Remove the transfer control device from the transfer assembly. Refer to TF-104, "
Removal and Installa-
tion" .
4. Remove the side oil seal.
CAUTION:
Do not damage shift cross.
INSTALLATION
1. Install the side oil seal until it is flush with the end face of case,
using Tool.
CAUTION:

Do not reuse oil seal.

Apply petroleum jelly to oil seal.
2. Install the transfer control device to the transfer assembly. Refer
to TF-104, "
Removal and Installation" .
3. Install the companion flange. Refer to TF-99, "
Removal and
Installation" .
4. Install the front propeller shaft. Refer to PR-4, "
Removal and Installation" .
SDIA2666E
Tool number : ST22360002 (J-25679-01)
SDIA2665E

TF-104
TRANSFER CONTROL DEVICE
Revision: August 20072004 QX56
TRANSFER CONTROL DEVICEPFP:33251
Removal and InstallationEDS00318
Refer to the figure for transfer control device removal and installation information.
CAUTION:

Change vehicle state to 2WD or AUTO, and then remove and install transfer control device.

Check 4WD shift indicator after installation.
1. Shift lever 2. Actuator
SDIA2654E

AIR BREATHER HOSE
TF-105
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
AIR BREATHER HOSEPFP:31098
Removal and InstallationEDS00319
Refer to the figure for air breather hose removal and installation information.
CAUTION:

Make sure there are no pinched or restricted areas on the air breather hose caused by bending or
winding when installing it.

Install the air breather hose into the air breather (metal connector) and actuator (case connector)
until the hose end reaches the base of the tube.

Install the air breather hose into the breather tube (metal connector) and transfer motor (case con-
nector) until the hose end reaches the end of the curved section.
SDIA2656E