clock setting INFINITI QX56 2004 Factory Service Manual

AT-256
TRANSMISSION ASSEMBLY
Revision: August 20072004 QX56
8. Remove crankshaft position sensor (POS) from A/T assembly.
9. Remove fluid cooler tube.
10. Remove dust cover from converter housing part.
11. Turn crankshaft, and remove the four tightening bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
12. Support A/T assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
13. Remove cross member with power tool.
14. Remove air breather hose. Refer to AT-253, "
Removal and
Installation" .
15. Disconnect A/T assembly connector.
16. Remove A/T fluid indicator pipe from A/T assembly.
17. Plug up openings such as the fluid charging pipe hole, etc.
18. Remove the A/T assembly to engine bolts with power tool.
19. Remove A/T assembly from vehicle using Tool and a transmis-
sion jack.

Secure torque converter to prevent it from dropping.

Secure A/T assembly to a transmission jack.
INSPECTION
Installation and Inspection of Torque Converter

After inserting a torque converter to a transmission, be sure to
check dimension A to ensure it is within the reference value
limit.
LCIA0334E
Tool number : — (J-47002)
LCIA0335E
SCIA0499E
Dimension A : 24.0 mm (0.94 in) or more
SAT0 1 7B

TRANSMISSION ASSEMBLY
AT-259
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
8. Remove crankshaft position sensor (POS) from A/T assembly.
9. Disconnect A/T fluid cooler tube from A/T assembly.
10. Remove dust cover from converter housing part.
11. Turn crankshaft, and remove the four tightening bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
12. Support A/T assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
13. Remove cross member with power tool.
14. Tilt the transmission slightly to keep the clearance between body
and transmission, and then disconnect air breather hose from charging pipe. Refer to AT- 2 5 3 , "
Removal
and Installation" .
15. Disconnect A/T assembly connector and transfer unit connector.
16. Remove A/T fluid indicator pipe.
17. Plug up openings such as the fluid charging pipe hole, etc.
18. Remove A/T assembly to engine bolts with power tool.
19. Remove A/T assembly from vehicle using Tool and a transmis-
sion jack.

Secure torque converter to prevent it from dropping.

Secure A/T assembly to a transmission jack.
NOTE:
The actual special service Tool may differ from Tool shown.
20. Remove transfer from A/T assembly. Refer to TF-109,
"REMOVAL AND INSTALLATION" .
INSPECTION
Installation and Inspection of Torque Converter

After inserting a torque converter to a transmission, be sure to
check dimension A to ensure it is within the reference value
limit.
LCIA0334E
Tool number : — (J-47002)
LCIA0335E
SCIA0499E
Dimension A : 24.0 mm (0.94 in) or more
SAT0 1 7B

NAVIGATION SYSTEM
AV-69
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
Application Items
Language Setting
How To Perform Language Setting
1. Select "Language/Unit".

Language setting can be switched.

Unit setting can be changed.
Clock Settings
How To Perform Clock Setting
1. Select “Clock”.

Select the "Hours" or "Minutes" key and tilt the joystick to the
right or left to adjust the time.

Turn ON and OFF daylight saving time.

Select the "Auto Adjust" key. The time will be reset to the GPS
time.

Select the "Select Time Zone" key. The [TIME ZONE] screen will
appear.
Beep Setting
How To Perform Beep Setting
1. Select “Beep Setting”.

When Beep Setting is on (indicator light on), a beep will sound if
the button is pushed.
NOTE:
Items in exception of Beep Setting ON/OFF.

An error beep.

An interrupted-screen beep.
Icon DescriptionReference
page
Language/Unit Settings of language or unit can be performed.AV- 6 9
Clock Settings of clock can be performed.AV- 6 9
Beep Setting Settings of beep sound can be performed.AV- 6 9
SKIA2065E
SKIA2063E
SKIA4829E

LT-154
ILLUMINATION
Revision: August 20072004 QX56

to power liftgate switch terminal 4

to front room/map lamp assembly (console box illumination) terminal 8

to AV switch terminal 4

to hazard switch terminal 4

to audio unit terminal 7

to rear sonar system OFF switch terminal 4

to 4WD switch terminal 8 (with 4-wheel drive)

to front air control terminal 24 and

to rear power vent window switch terminal 6

to DVD player terminal 10 (with DVD entertainment system)

to pedal adjusting switch terminal 6

to A/T device terminal 12

to front heated seat switches terminal 6

to VDC OFF switch terminal 4

to tow mode switch terminal 4

to headlamp aiming switch terminal 4

to clock terminal 4 and

to combination meter terminal 18.
Ground is supplied

to illumination control switch terminal 3

to glove box lamp terminal –

to display control unit terminal 3

to rear heated seat switches terminal 6

to electric brake (pre-wiring) terminal 1 and

to compass and thermometer terminal 7

through grounds M57, M61 and M79, and

to NAVI control unit terminal 30

to rear air control terminal 3 and

to rear audio remote control unit terminal 15

through grounds B117 and B132.
With power and ground supplied, illumination lamps illuminate.
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 1ST or 2ND position (or if auto light system is acti-
vated), and the ignition switch is turned from ON or ACC to OFF, the battery saver control function is activated.
Under this condition, the illumination lamps remain illuminated for 5 minutes, then the illumination lamps are
turned off.
When the lighting switch is turned from OFF to 1ST or 2ND position (or if auto light system is activated) after
illumination lamps are turned off by the battery saver control, the illumination lamps illuminate again.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
CAN Communication System DescriptionEKS007DB
Refer to LAN-5, "CAN COMMUNICATION" .