blower INFINITI QX56 2006 Factory Workshop Manual

DEFROSTER DOOR MOTORATC-159
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
DEFROSTER DOOR MOTORPFP:27733
Removal and InstallationEJS003YI
Defroster Door Motor - Front Heater and Cooling Unit Assembly
REMOVAL
1. Remove the BCM. Refer to BCS-20, "BCM" .
2. Remove the Bose speaker amplifier, if equipped. Refer to AV- 5 5 , "
BOSE SPEAKER AMP." .
3. Disconnect the defroster door motor electrical connector.
4. Remove the three screws and remove the defroster door motor.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0139E
1. Front heater and cooling unit assembly 2. Intake door motor 3. Air mix door motor (driver)
4. Variable blower control 5. Air mix door motor (passenger) 6. Mode door motor
7. Defroster door motor

ATC-160
INTAKE DOOR MOTOR
Revision: November 20092006 QX56
INTAKE DOOR MOTORPFP:27730
Removal and InstallationEJS003YJ
Intake Door Motor - Front Heater and Cooling Unit Assembly
REMOVAL
1. Remove the front heater and cooling unit assembly. Refer to ATC-154, "FRONT HEATER AND COOLING
UNIT ASSEMBLY" .
2. Remove the steering member from the front heater and cooling unit assembly.
3. Disconnect the intake door motor electrical connector.
4. Remove the three screws and remove the intake door motor.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0139E
1. Front heater and cooling unit assembly 2. Intake door motor 3. Air mix door motor (driver)
4. Variable blower control 5. Air mix door motor (passenger) 6. Mode door motor
7. Defroster door motor

MODE DOOR MOTORATC-161
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
MODE DOOR MOTORPFP:27731
Removal and InstallationEJS003YK
Mode Door Motor - Front Heater and Cooling Unit Assembly
REMOVAL
1. Remove the center console lower cover LH. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Disconnect the mode door motor electrical connector.
3. Remove the two screws and remove the mode door motor.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0139E
1. Front heater and cooling unit assembly 2. Intake door motor 3. Air mix door motor (driver)
4. Variable blower control 5. Air mix door motor (passenger) 6. Mode door motor
7. Defroster door motor

ATC-162
AIR MIX DOOR MOTOR
Revision: November 20092006 QX56
AIR MIX DOOR MOTOR PFP:27732
ComponentsEJS003YL
Air Mix Door Motors - Front Heater and Cooling Unit Assembly
Removal and InstallationEJS003YM
FRONT AIR MIX DOOR MOTOR (DRIVER)
Removal
1. Remove the front heater and cooling unit assembly. Refer to ATC-154, "FRONT HEATER AND COOLING
UNIT ASSEMBLY" .
2. Remove the steering member from the front heater and cooling unit assembly.
3. Disconnect the air mix door motor electrical connector.
4. Remove the three screws and remove the air mix door motor.
Installation
Installation is in the reverse order of removal.
LJIA0139E
1. Front heater and cooling unit assembly 2. Intake door motor 3. Air mix door motor (driver)
4. Variable blower control 5. Air mix door motor (passenger) 6. Mode door motor
7. Defroster door motor

ATC-164
VARIABLE BLOWER CONTROL
Revision: November 20092006 QX56
VARIABLE BLOWER CONTROLPFP:27200
Removal and InstallationEJS003YN
Variable Blower Control - Front Heater and Cooling Unit Assembly
REMOVAL
1. Remove the glove box assembly. Refer to IP-14, "Lower Instrument Panel RH and Glove Box" .
2. Disconnect the variable blower control electrical connector.
3. Remove the two screws and remove the variable blower control.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0139E
1. Front heater and cooling unit assembly 2. Intake door motor 3. Air mix door motor (driver)
4. Variable blower control 5. Air mix door motor (passenger) 6. Mode door motor
7. Defroster door motor

REAR BLOWER MOTOR RESISTORATC-165
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
REAR BLOWER MOTOR RESISTORPFP:27150
Removal and InstallationEJS003YO
Rear Blower Motor Resistor
REMOVAL
1. Remove the luggage side finisher lower RH. Refer to EI-40, "LUGGAGE FLOOR TRIM" .
2. Disconnect the rear blower motor resistor electrical connector.
3. Remove the two screws and remove the rear blower motor resistor.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0055E
1. Rear blower motor 2. Rear blower motor case 3. Rear blower motor resistor

ATC-174
REFRIGERANT LINES
Revision: November 20092006 QX56
Rear A/C
NOTE:
Refer to AT C - 7 , "
Precautions for Refrigerant Connection" .
1. High-pressure service valve 2. Grommet 3. High-pressure pipe
4. Refrigerant pressure sensor 5. Condenser 6. Compressor shaft seal
7. High-pressure flexible hose 8. Low-pressure flexible hose 9. Low-pressure service valve
10. Low-pressure pipe 11. Expansion valve (front) 12. Drain hose
WJIA2315E
1. Rear heater and cooling unit assembly 2. Rear A/C pipes 3. Rear A/C heater core pipes
4. Rear heater core hose 5. Rear blower motor6. Underfloor rear A/C pipes
7. Underfloor rear heater core pipes A. Bolt torque specifications B. Leak checking order (l - r)
C. Tightening torque D. Wrench sizeE. O-ring size
⇐ Front
NOTE: The O-ring size 8 is the high-side and the O-ring size 16 is the low-side.

REFRIGERANT LINESATC-181
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
8. Remove the rear high- and low-pressure pipes bracket bolt (A)
to release the bracket.

Rear blower motor (1)

⇐: Front
9. Remove the rear high- and low-pressure pipes bolt (A) to dis- connect the rear high- and low-pressure pipes from the rear
expansion valve (1).

⇐: Front
CAUTION:
Cap or wrap the joint of the pipes with suitable material
such as vinyl tape to avoid the entry of air.
10. Disconnect the following electrical connectors:

Rear air mix door motor (1)

Rear blower motor resistor (2)

Rear blower motor (3)

⇐ : Front
11. Disconnect the ducts from the rear heater and cooling unit assembly. Refer to ATC-166, "
Components" .
12. Remove the rear heater and cooling unit assembly. CAUTION:
Cap or wrap the joint of the pipes with suitable material such as vinyl tape to avoid the entry of air.
13. Remove the rear high- and low-pressure A/C pipes.
INSTALLATION
Installation is in the reverse order of removal.
Refer to ATC-173, "
Components" .
CAUTION:

Replace the O-ring of the high/low-pressure pipe with a new one, then apply compressor oil to it
when installing it.

After charging refrigerant, check for leaks.
Removal and Installation for Underfloor Rear High- and Low-pressure A/C and
Heater Core Pipes
EJS005Y9
REMOVAL
1. Drain the coolant from the engine cooling system. Refer to CO-10, "Changing Engine Coolant" .
2. Disconnect the battery negative terminal.
3. Disconnect the generator harness.
4. Discharge the refrigerant. Refer to ATC-171, "
HFC-134a (R-134a) Service Procedure" .
WJIA2312E
WJIA2313E
WJIA2314E

ATC-184
REFRIGERANT LINES
Revision: November 20092006 QX56
Removal and Installation for Front EvaporatorEJS003Z1
Front Heater and Cooling Unit Assembly
REMOVAL
1. Remove the front heater core. Refer to ATC-157, "FRONT HEATER CORE" .
LJIA0138E
1. Heater core cover2. Heater core pipe bracket 3. Heater core
4. Upper bracket 5. Upper heater and cooling unit case 6. A/C evaporator
7. Lower heater and cooling unit case 8. Blower motor 9. Variable blower control

REFRIGERANT LINESATC-185
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
2. Remove the defroster mode door arm.
3. Separate the heater core and cooling unit case.
4. Remove the evaporator.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the O-rings on the low-pressure flexible hose and the high-pressure pipe with new ones.
Apply compressor oil to the O-rings when installing them.
Removal and Installation for Rear EvaporatorEJS003Z2
Rear Heater and Cooling Unit Assembly
LJIA0135E
1. Front cover2. Evaporator and heater core case 3. Evaporator
4. Side cover 5. Heater core6. Rear blower motor
7. Blower motor case 8. Rear blower motor resistor