relay INFINITI QX56 2011 Factory Owner's Manual

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-47
< ECU DIAGNOSIS INFORMATION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Note 1: Confirm tire pressure is standard value.
Note 2: Refer to BRC-16, "
System Description" for ON/Blinking/OFF conditions of each warning lamp and indi-
cator lamp.
Note 3: Models with 4WD System
Note 4: Models with Advanced Driver Assistance System
Note 5: USS means “hill start assist”.
Fail-safeINFOID:0000000006222580
VDC FUNCTION, TCS FUNCTION, hill start assi st FUNCTION AND BRAKE LIMITED SLIP DIFFER-
ENTIAL (BLSD) FUNCTION
VDC warning lamp in combination meter turn ON w hen a malfunction occurs in system [ABS actuator and
electric unit (control unit)]. The control is suspended for VDC function, TCS function, hill start assist function
and brake limited slip differential (BLSD) function. T he Vehicle status becomes the same as models without
PRESS SENSORBrake pedal not depressed Approx. 0 bar
Brake pedal depressed (
−40) – (+300) bar
ACCUM PRESS SEN With ig nition switch ON Approx. 0 – 210 bar (Proportional to the
amount of accumulated pressure in the
accumulator)
CONT PRESS SEN
(Note 4)Brake pedal not depressed Approx. 0 bar
Brake pedal depressed ( −40) – (+300) bar
EBD SIGNAL EBD is active On
EBD is inactive Off
ABS SIGNAL ABS is active On
ABS is inactive Off
TCS SIGNAL TCS is active On
TCS is inactive Off
VDC SIGNAL VDC is active On
VDC is inactive Off
EBD FAIL SIG In EBD fail-safe On
EBD is normal Off
ABS FAIL SIG In ABS fail-safe On
ABS is normal Off
TCS FAIL SIG In TCS fail-safe On
TCS is normal Off
VDC FAIL SIG In VDC fail-safe On
VDC is normal Off
CRANKING SIG At cranking On
Other than at cranking Off
FLUID LEV SW When brake fluid level switch is ON (brake fluid level
is less than the specified level)
On
When brake fluid level switch is OFF Off
PARK BRAKE SW When parking brake is active On
Parking brake is released Off
STP ON RLY Stop lamp relay is active On
Stop lamp relay is inactive Off
USS SIG
(Note 5)hill start assist is active On
hill start assist is inactive Off
Monitor item Condition Reference values in normal operation
Revision: 2010 May2011 QX56

BRC-48
< ECU DIAGNOSIS INFORMATION >[WITH VDC]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
VDC function, TCS function, hill start assist function and
brake limited slip differential (BLSD) function. How-
ever, ABS function and EBD function are operated normally.
ABS FUNCTION
ABS warning lamp and VDC warning lamp in combinati on meter turn ON when a malfunction occurs in system
[ABS actuator and electric unit (control unit)]. The c ontrol is suspended for VDC function, TCS function, ABS
function, hill start assist function and brake limited sl ip differential (BLSD) function. The vehicle status
becomes the same as models without VDC function, TCS f unction, ABS function, hill start assist function and
brake limited slip differential (BLSD) function. However, EBD function is operated normally.
NOTE:
ABS self-diagnosis sound may be heard the same as in the normal condition, because self-diagnosis is per-
formed when ignition switch turns ON and when vehicle initially starts.
EBD FUNCTION
ABS warning lamp, brake warning lamp and VDC warning lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC
function, TCS function, ABS function, EBD function, hill start assist function and brake limited slip differential
(BLSD) function. The vehicle status becomes the sa me as models without VDC function, TCS function, ABS
function, EBD function, hill star t assist function and brake limited slip differential (BLSD) function.
DTC Malfunction detected condition Fail-safe condition
C1101 When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function (only when both 2 rear wheels are malfunctioning)
 hill start assist function
 Brake limited slip differential (BLSD) function
C1102 When an open circuit is detected in rear LH wheel sensor circuit.
C1103 When an open circuit is detected in front RH wheel sensor circuit.
C1104 When an open circuit is detected in front LH wheel sensor circuit.
C1105
 When power supply voltage of rear RH wheel sensor is low.
 When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
 When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not normal.
C1106  When power supply voltage of rear LH wheel sensor is low.
 When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
 When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor-
mal.
C1107  When power supply voltage of front RH wheel sensor is low.
 When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
 When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
C1108  When power supply voltage of front LH wheel sensor is low.
 When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
 When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
C1109  When ignition voltage is 10 V or less.
 When ignition voltage is 16 V or more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 1111
 When a malfunction is detected in motor or motor relay.
 When a low pressure malfunction is detected in accumulator.
 When a malfunction is detected in accumulator pressure sensor.
Revision: 2010 May2011 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-49
< ECU DIAGNOSIS INFORMATION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C 111 5 When difference in wheel speed between any wheel and others is detected during
the vehicle is driven, because of installation of other tires than specified. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 111 6
 When stop lamp switch signal is not input when brake pedal depress.
 When stop lamp switch signal is not input when stop lamp relay operates.
C 111 8
*1When a malfunction is detected in transfer control unit system.
C1120 When a malfunction is detec ted in front LH ABS IN valve.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD) function
C1121 When a malfunction is detec
ted in front LH ABS OUT valve.
C1122 When a malfunction is detected in front RH ABS IN valve.
C1123 When a malfunction is det ected in front RH ABS OUT valve.
C1124 When a malfunction is detected in rear LH ABS IN valve.
C1125 When a malfunction is detected in rear LH ABS OUT valve.
C1126 When a malfunction is det ected in rear RH ABS IN valve.
C1127 When a malfunction is detected in rear RH ABS OUT valve.
C1130 When a malfunction is detected in ECM system. The following functions are sus-
pended.
 VDC function
 TCS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1140 When a malfunction is detected in actuator relay. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1142
*2When a malfunction is detected in master cylinder pressure sensor or control pres-
sure sensor. The following functions are sus-
pended.
 VDC function
 TCS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1143 When a malfunction is detected in steering angle sensor.
C1144 When neutral position adjustment of steering angle sensor is not complete.
C1145
 When a malfunction is detected in yaw rate signal.
 When yaw rate signal is not continuously received for 2 seconds or more.
 When side G signal is not continuously received for 2 seconds or more.
 When decel G signal is not continuously received for 2 seconds or more.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1146 When a malfunction is detected in side/decel G signal.
C1155
 When brake fluid level low signal is detected.
 When an open circuit is detected in brake fluid level switch circuit.
C1160 When calibration of yaw rate/side/decal G sensor is not complete.
C1164 When a malfunction is detected in cut valve 1. The following functions are sus- pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD) function
C1165 When a malfunction is detected in cut valve 2.
C1166 When a malfunction is detected in suction valve 1.
C1167 When a malfunction is detected in suction valve 2. DTC Malfunction detected condition Fail-safe condition
Revision: 2010 May2011 QX56

C1111 PUMP MOTORBRC-75
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1111 PUMP MOTOR
DTC LogicINFOID:0000000006222599
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF and depress the brake pedal 20 times or more.
2. Start the engine and wait for 3 minutes or more. CAUTION:
Never drive the vehicle.
3. Depress the brake pedal, and then operate the ABS act uator and electric unit (control unit) motor repeats
ON and OFF 4 times or more.
CAUTION:
Never drive the vehicle.
4. Perform self-diagnosis for “ABS”.
Is DTC
“C 1111” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-75, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222600
1.CHECK ABS MOTOR AND MOTOR RELAY POWER SUPPLY
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
4. Turn the ignition switch ON. CAUTION:
Never start engine.
5. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK ABS MOTOR AND MOTOR RELAY POWER SUPPLY CIRCUIT
DTC Display Item Malfunction detected condition Possible causes
C 1111 P U M P M O T O R  When a malfunction is detected in motor or motor
relay.
 When a low pressure malfunction is detected in ac- cumulator.
 When a malfunction is detected in accumulator
pressure sensor.  Harness or connector
 ABS actuator and electric unit
(control unit)
Fusible link
 Battery power supply system
 Motor/accumulator assembly
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 4 Ground Battery voltage
E37 47
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 4 Ground Battery voltage
E37 47
Revision: 2010 May2011 QX56

C1116 STOP LAMP SWITCHBRC-79
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1116 STOP LAMP SWITCH
DTC LogicINFOID:0000000006222603
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C 111 6” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-79, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222604
1.CHECK STOP LAMP FOR ILLUMINATION
Depress brake pedal and check that stop lamp turns ON.
Does stop lamp turn ON?
YES >> GO TO 2.
NO >> Check stop lamp system. Refer to EXL-40, "
Wiring Diagram".
2.CHECK STOP LAMP SWITCH CLEARANCE
1. Turn the ignition switch OFF.
2. Check stop lamp clearance. Refer to BR-7, "
Inspection and Adjustment".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Adjust stop lamp switch clearance. Refer to BR-7, "
Inspection and Adjustment".
3.CHECK STOP LAMP SWITCH POWER SUPPLY (1)
1. Disconnect ABS actuator and electric unit (control unit) harness connector.
2. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
3. Turn the ignition switch ON. CAUTION:
Never start engine.
4. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
DTC Display Item Malfunction detected condition Possible causes
C1116 STOP LAMP SW  When stop lamp switch signal is not input when brake
pedal depress.
 When stop lamp switch signal is not input when stop lamp relay operates.  Harness or connector
 Stop lamp switch
 Stop lamp relay
 ABS actuator and electric unit
(control unit)
 Battery power supply system
ABS actuator and electric unit (control unit) — Condition Voltage
Connector Terminal
E36 17 Ground Brake pedal depressed
Approx. 0 V
Brake pedal not depressed
Revision: 2010 May2011 QX56

BRC-82
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1116 STOP LAMP SWITCH
YES >> GO TO 10.
NO >> Repair or replace error-detected parts.
10.CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to BRC-85, "
Component Inspection (Stop lamp Switch)".
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair or replace stop lamp switch. Refer to BR-20, "
Removal and Installation".
11 .CHECK STOP LAMP SWITCH POWER SUPPLY (4)
1. Check voltage between stop lamp switch harness connector and ground.
2. Turn the ignition switch ON. CAUTION:
Never start engine.
3. Check voltage between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES >> Check pin terminals and connection of stop lamp switch harness connector for abnormal condi- tions. Repair or replace error-detected parts.
NO >> GO TO 12.
12.CHECK STOP LAMP SWITCH CIRCUIT (4)
1. Turn the ignition switch OFF.
2. Check 10A fuse (#7).
3. Disconnect fuse block (J/B) harness connector.
4. Check fuse block (J/B) pin terminals for damage or loose connection with harness connector.
5. Check continuity between stop lamp swit ch harness connector and fuse block (J/B).
Is the inspection result normal?
YES >> Perform trouble diagnosis for battery power supply. Refer to PG-11, "Wiring Diagram - BATTERY
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
13.CHECK STOP LAMP RELAY POWER SUPPLY (1)
1. Turn the ignition switch OFF.
2. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
3. Turn the ignition switch ON. CAUTION:
Never start engine.
4. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
Stop lamp switch
— Voltage
Connector Terminal
E115 1 Ground Approx. 0 V
Stop lamp switch — Voltage
Connector Terminal
E115 1 Ground Battery voltage
Stop lamp switch Fuse block (J/B) Continuity
Connector Terminal Connector Terminal
E115 1 E103 8F Existed
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 46 Ground Approx. 0 V
Revision: 2010 May2011 QX56

C1116 STOP LAMP SWITCHBRC-83
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 18.
NO >> GO TO 14.
14.CHECK STOP LAMP RELAY CIRCUIT (1)
1. Turn the ignition switch OFF.
2. Disconnect stop lamp relay harness connector.
3. Check continuity between ABS actuator and electr ic unit (control unit) harness connector and stop lamp
relay harness connector.
4. Check continuity between ABS actuator and elec tric unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 15.
NO >> Repair or replace error-detected parts.
15.CHECK STOP LAMP RELAY
Check stop lamp relay. Refer to BRC-86, "
Component Inspection (Stop Lamp Relay)".
Is the inspection result normal?
YES >> GO TO 16.
NO >> Repair or replace stop lamp relay.
16.CHECK STOP LAMP RELAY POWER SUPPLY (2)
1. Turn the ignition switch OFF.
2. Check voltage between stop lamp relay harness connector and ground.
3. Turn the ignition switch ON. CAUTION:
Never start engine.
4. Check voltage between stop lamp relay harness connector and ground.
Is the inspection result normal?
YES >> Check pin terminals and connection of stop lamp relay harness connector for abnormal condi- tions. Repair or replace error-detected parts.
NO >> GO TO 17.
ABS actuator and electric unit (control unit) —Voltage
Connector Terminal
E36 46 Ground Battery voltage
ABS actuator and electric unit (control unit) Stop lamp relay Continuity
Connector Terminal Connector Terminal
E3646E58 2Existed
ABS actuator and electric unit (control unit) —Continuity
Connector Terminal
E36 46 Ground Not existed
Sto p l am p rela y —Voltage
Connector Terminal
E58 1 Ground Approx. 0 V
Sto p l am p rela y —Voltage
Connector Terminal
E58 1 Ground Battery voltage
Revision: 2010 May2011 QX56

BRC-84
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1116 STOP LAMP SWITCH
17.CHECK STOP LAMP RELAY CIRCUIT (2)
1. Turn the ignition switch OFF.
2. Check 10A fuse (#57).
3. Disconnect IPDM E/R harness connector.
4. Check IPDM E/R pin terminals for dam age or loose connection with harness connector.
5. Check continuity between stop lamp relay harness connector and IPDM E/R harness connector.
Is the inspection result normal?
YES >> Perform trouble diagnosis for ignition power supply. Refer to PG-89, "Wiring Diagram - IGNITION
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
18.CHECK STOP LAMP RELAY POWER SUPPLY (3)
1. Turn the ignition switch OFF.
2. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
3. Turn the ignition switch ON. CAUTION:
Never start engine.
4. Check voltage between stop lamp relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 22.
NO >> GO TO 19.
19.CHECK STOP LAMP RELAY CIRCUIT (3)
1. Turn the ignition switch OFF.
2. Disconnect stop lamp relay harness connector.
3. Check continuity between ABS actuator and electr ic unit (control unit) harness connector and stop lamp
relay harness connector.
4. Check continuity between ABS actuator and elec tric unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 20.
Stop lamp relay IPDM E/R Continuity
Connector Terminal Connector Terminal
E581E1559Existed
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 37 Ground Approx. 0 V
ABS actuator and electric unit (control unit) — Condition Voltage
Connector Terminal
E36 37 Ground Brake pedal depressed Battery voltage
Brake pedal not depressed Approx. 0 V
ABS actuator and electric unit (c ontrol unit) Stop lamp relay
Continuity
Connector Terminal Connector Terminal
E3637E58 5Existed
ABS actuator and electric unit (control unit) —Continuity
Connector Terminal
E36 37 Ground Not existed
Revision: 2010 May2011 QX56

C1116 STOP LAMP SWITCHBRC-85
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
NO >> Repair or replace error-detected parts.
20.CHECK STOP LAMP RELAY POWER SUPPLY (4)
1. Check voltage between stop lamp relay harness connector and ground.
2. Turn the ignition switch ON. CAUTION:
Never start engine.
3. Check voltage between stop lamp relay harness connector and ground.
Is the inspection result normal?
YES >> Check pin terminals and connection of stop lamp relay harness connector for abnormal condi- tions. Repair or replace error-detected parts.
NO >> GO TO 21.
21.CHECK STOP LAMP RELAY CIRCUIT (4)
1. Check 10A fuse (#7).
2. Disconnect fuse block (J/B) harness connector.
3. Check fuse block (J/B) pin terminals for damage or loose connection with harness connector.
4. Check continuity between stop lamp re lay harness connector and fuse block (J/B).
Is the inspection result normal?
YES >> Perform trouble diagnosis for battery power supply. Refer to PG-11, "Wiring Diagram - BATTERY
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
22.CHECK TERMINAL
Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness
connector.
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace error-detected parts.
Component Inspection (Stop lamp Switch)INFOID:0000000006222605
1.CHECK STOP LAMP SWITCH
1. Turn the ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check continuity when stop lamp switch is operated.
Sto p l am p rela y —Voltage
Connector Terminal
E58 3 Ground Battery voltage
Sto p l am p rela y —Voltage
Connector Terminal
E58 3 Ground Battery voltage
Stop lamp relay Fuse block (J/B) Continuity
Connector Terminal Connector Terminal
E58 3 E103 8F Existed
Revision: 2010 May2011 QX56

BRC-86
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1116 STOP LAMP SWITCH
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace stop lamp switch. Refer to
BR-20, "
Removal and Installation".
Component Inspection (Stop Lamp Relay)INFOID:0000000006222606
1.CHECK STOP LAMP RELAY
1. Apply 12 V to stop lamp relay connector terminal (1 and 2). CAUTION:
 Never make the terminals short.
 Connect the fuse between the termina ls when applying the voltage.
2. Check continuity between stop lamp relay connector terminals.
3. Check resistance between stop lamp relay connector terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace stop lamp relay.
Stop lamp switch Condition Continuity
Te r m i n a l
1 − 2
3 − 4 When stop lamp switch is released
(When brake pedal is depressed)
Existed
When stop lamp switch is pressed
(When brake pedal is released) Not existed
Sto p l am p rela y
Condition Continuity
Te r m i n a l
3 − 5 Apply 12 V to stop lamp relay connector
terminal (1 and 2)
Existed
Do not apply 12 V to stop lamp relay con-
nector terminal (1 and 2) Not existed
Sto p l am p rela y Resistance
Te r m i n a l
1 − 2Approx. 50 Ω
Revision: 2010 May2011 QX56