ISUZU AXIOM 2002 Service Repair Manual

LIGHTING SYSTEM8A±5
6. Turn the headlight low beam on.
7. Adjust the CUTLINE 30 mm (1.18 in) below the
horizontal line (H).
801R200011
Vertical Adjustment
Use a screwdriver for vertical adjustment.
801R200012

8A±6LIGHTING SYSTEM
Side Marker Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the front combination light (1).

Remove the screw.
3. Remove the bulb (2).

Remove the side marker light socket (3) by turning it
counterclockwise.

Remove the bulb by turning it counterclockwise
while pushing it at the same time.
801R200013
Installation
To install, follow the removal steps in the reverse order.

LIGHTING SYSTEM8A±7
Taillight Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the rear combination light assembly (1).

Remove two screws.

Pull out the rear combination light assembly
outside.
803R200011
3. Remove the bulb (1).

Remove the taillight socket by turning it
counterclockwise.

Remove the bulb by turning it counterclockwise
while pushing it at the same time.
803R200002
Installation
To install, follow the removal steps in the reverse order.

8A±8LIGHTING SYSTEM
License Plate Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the license plate light garnish.

Remove the three screws.
3. Remove the lens cover (3).

Remove two screws.
4. Remove the license plate light socket by turning it
counterclockwise.
5. Remove the bulb (2).

Pull out the bulb from the socket (1).
803R200003
Installation
To install, follow the removal steps in the reverse order.
Stoplight Bulb
Removal and Installation
Refer to Taillight Bulb in this section.

LIGHTING SYSTEM8A±9
High Mounted Stoplight Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the high mounted stoplight assembly (1).

Remove the cover (2).

Remove two screws.

Disconnect the connector.
803R200004
Installation
To install, follow the removal steps in the reverse order.
High Mounted Stoplight Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the cover.
3. Remove the high mounted stoplight assembly (1).

Remove two screw.
4. Remove the bulb (2).

Remove the socket by turning it counterclockwise.
803R200005
Installation
To install, follow the removal steps in the reverse order.

8A±10LIGHTING SYSTEM
Backup Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the rear combination light assembly.

Refer to
Taillight Bulb in this section.
3. Remove the bulb (1).

Remove the backup light socket by turning it
counterclockwise.

Pull out the bulb from the socket.
803R200007
Installation
To install, follow the removal steps in the reverse order.
Front Turn Signal Light Bulb
Removal and Installation
Refer to Side Marker Light Bulb in this section.

LIGHTING SYSTEM8A±11
Rear Turn Signal Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the rear combination light assembly.

Refer to
Taillight Bulb in this section.
3. Remove the bulb (1).

Remove the rear turn signal light socket by turning it
counterclockwise.

Remove the bulb by turning it counterclockwise
while pushing it at the same time.
803R200006
Installation
To install, follow the removal steps in the reverse order.
Dome Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).

Pull out the bulb.
825RW075
Installation
To install, follow the removal steps in the reverse order.

8A±12LIGHTING SYSTEM
Map Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).

Pull out the bulb.
805R200002
Installation
To install, follow the removal steps in the reverse order.
Courtesy Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).

Pull out the bulb.
825RW076
Installation
To install, follow the removal steps in the reverse order.

LIGHTING SYSTEM8A±13
Luggage Room Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).

Pull out the bulb.
805R200001
Installation
To install, follow the removal steps in the reverse order.
Shift Lever Illumination Light Bulb (A/T)
Removal
1. Disconnect the battery ground cable.
2. Remove the console assembly.

Refer to
Consol in Body Structure section.
3. Remove the indicator cover (1).
4. Remove the bulb (2).

Turn the bulb socket counterclockwise.

Pull out the bulb from the socket.
825R200022
Installation
To install, follow the removal steps in the reverse order.

8A±14LIGHTING SYSTEM
Vanity Mirror Illumination Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (1).
3. Remove the bulb (2).
805R200004
Installation
To install, follow the removal steps in the reverse order.
Switch Unit Assembly Illumination Light Bulb
(Power/Winter & Intelligent Suspension Switch)
Removal
1. Disconnect the battery ground cable.
2. Remove the center cluster assembly.

Refer to
Instrument Panel Assembly in Body
Structure
section.
3. Remove the audio.

Refer to
Audio in Entertainment section.
4. Remove the illumination light bulb.
825R200036
Installation
To install, follow the removal steps in the reverse order.