sensor ISUZU AXIOM 2002 Service Service Manual

FRONT SUSPENSION3C±19
Upper Ball Joint
Upper Ball Joint and Associated Parts
450RW004
Legend
(1) Bolt and Nut(2) Upper Ball Joint
(3) Nut and Cotter Pin
Removal
1. Raise the vehicle and support the frame with suitable
safety stands.
2. Remove the speed sensor from the knuckle.

3D±10REAR SUSPENSION
Upper Link
Upper Link and Associated Parts
460RW006
Legend
(1) Bolt and Nut (Axle side)
(2) Rubber Plate(3) Upper Link
(4) Protector (Left side only)
(5) Bolt (Frame side)
Removal
1. Remove fuel tank. Refer to Engine Fuel in Engine
section.
2. Remove the speed sensor cable from the upper link.
3. Remove bolt, nut, rubber plate and protector.
4. Remove upper link.
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
1. Upper link
2. Rubber bushing

Remove the rubber bushing by using remover
J±43008.
460RY00006

REAR SUSPENSION3D±11

Install the rubber bushing by using to installer
J±43008.
NOTE: When mounting rubber bushings, be sure not to
use grease on bushings or any other nearby part.
460RY00007
Installation
1. Install upper link. Make sure that the upper link is in its
correct position.
NOTE: When mounting upper link, be sure not to use
grease bushings or any other nearby part.
460RW012
2. Install bolt, nut, rubber plate and protector. Tighten
the bolts and nuts lightly, then retighten them to the
specified torque after the vehicle is at curb height.
Torque: 137 N´m (101 lb ft)
3. Install speed sensor cable.
4. Install fuel tank.

3D±28REAR SUSPENSION
Upper Link
Upper Link and Associated Parts
460RW006
Legend
(1) Bolt and Nut (Axle side)
(2) Rubber Plate(3) Upper Link
(4) Protector (Left side only)
(5) Bolt (Frame side)
Removal
1. Remove fuel tank. Refer to Engine Fuel in Engine
section.
2. Remove the speed sensor cable from the upper link.
3. Remove bolt, nut, rubber plate and protector.
4. Remove upper link.
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
1. Upper link
2. Rubber bushing

Remove the rubber bushing by using remover
J±43008.
460RY00006

REAR SUSPENSION3D±29

Install the rubber bushing by using to installer
J±43008.
NOTE: When mounting rubber bushings, be sure not to
use grease on bushings or any other nearby part.
460RY00007
Installation
1. Install upper link. Make sure that the upper link is in its
correct position.
NOTE: When mounting upper link, be sure not to use
grease bushings or any other nearby part.
460RW012
2. Install bolt, nut, rubber plate and protector. Tighten
the bolts and nuts lightly, then retighten them to the
specified torque after the vehicle is at curb height.
Torque: 137 N´m (101 lb ft)
3. Install speed sensor cable.
4. Install fuel tank.

INTELLIGENT SUSPENSION3F±1
AXIOM
SUSPENSION
INTELLIGENT SUSPENSION CONTROL
CONTENTS
Service Precaution 3F±2. . . . . . . . . . . . . . . . . . . . . .
General Description 3F±2. . . . . . . . . . . . . . . . . . . . .
PIN ASSIGNMENT TABLE 3F±4. . . . . . . . . . . . .
System Components 3F±4. . . . . . . . . . . . . . . . . . .
Control Unit 3F±4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Actuator 3F±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Damping Force Shock Absorber 3F±4
Warning Lamp 3F±4. . . . . . . . . . . . . . . . . . . . . . . .
Vertical G-Sensor 3F±5. . . . . . . . . . . . . . . . . . . . . .
Lateral G-Sensor 3F±5. . . . . . . . . . . . . . . . . . . . . .
Acronyms and Abbreviations 3F±5. . . . . . . . . . . .
General Diagnosis 3F±5. . . . . . . . . . . . . . . . . . . . . . .
General Information 3F±5. . . . . . . . . . . . . . . . . . . .
Service Precautions 3F±5. . . . . . . . . . . . . . . . . . .
Computer System Service Precautions 3F±5. . .
General Service Precautions 3F±5. . . . . . . . . . . .
Parts Handling 3F±5. . . . . . . . . . . . . . . . . . . . . . . .
FLASHING CODES 3F±6. . . . . . . . . . . . . . . . . . . .
CLEAR DTC 3F±7. . . . . . . . . . . . . . . . . . . . . . . . . .
INTERMITTENT CONDITIONS 3F±8. . . . . . . . .
BULB CHECK 3F±8. . . . . . . . . . . . . . . . . . . . . . . . .
DTC CHECK 3F±8. . . . . . . . . . . . . . . . . . . . . . . . . .
Connector List 3F±14. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Identification 3F±16. . . . . . . . . . . . . . . . . . . . . . . . .
DTC2 Actuator Coil Over Current 3F±17. . . . . . . . . .
Circuit Description 3F±17. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±17. . . . . . . . . . . . . . . . . . . . . . . .
DTC3 Actuator Coil/Position Sensor Open
Circuit or Short 3F±19. . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Description 3F±19. . . . . . . . . . . . . . . . . . . . . Diagnostic Aids 3F±19. . . . . . . . . . . . . . . . . . . . . . . .
DTC4 G-Sensor Open Circuit or Short 3F±22. . . . .
Circuit Description 3F±22. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±22. . . . . . . . . . . . . . . . . . . . . . . .
DTC5 Vehicle Speed Sensor Open Circuit
or Short 3F±23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Description 3F±23. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±23. . . . . . . . . . . . . . . . . . . . . . . .
DTC6 Stop Lamp Switch Open Circuit
or Short 3F±25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Description 3F±25. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±25. . . . . . . . . . . . . . . . . . . . . . . .
DTC7 Engine Speed Signal Open Circuit
or Short 3F±27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Description 3F±27. . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 3F±27. . . . . . . . . . . . . . . . . . . . . . . .
DTC9 Control Unit Abnormality 3F±28. . . . . . . . . . . .
Control Unit 3F±32. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 3F±33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 3F±33. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Actuator 3F±34. . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 3F±35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 3F±35. . . . . . . . . . . . . . . . . . . .
Installation 3F±35. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Shock Absorber 3F±36. . . . . . . . . . . . . . . . . . . .
Removal 3F±37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 3F±37. . . . . . . . . . . . . . . . . . . .
Installation 3F±37. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3F±2INTELLIGENT SUSPENSION
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
General Description
Intellignet suspension control uses a microcomputer as a
control unit to judge running conditions including engine
revolution from Powertrain Control Module, vehicle speed
from vehicle speed sensor, a brake switch signal, and
vertical and lateral G-sensor signal, then sets optimum
damping force so that best running stability can be
achieved.

3F±4INTELLIGENT SUSPENSION
PIN ASSIGNMENT TABLE
PIN
No.NAMEPIN
No.NAMEPIN
No.NAMEPIN
No.NAME
1GND17KI-FR B33KI-RR PSW49STOP
2NC18KI-FR D34KI-RL Vcc50T-SW
3Vdd19KI-FL B35KI-FR GND51M-SW
4KI-FR A20KI-FL D36KI-FR Vs52Txd
5KI-FR C21KI-RR B37KI-FL PSW53Vig
6KI-FL A22KI-RR D38KI-FL Vs54NC
7KI-FL C23KI-RL B39KI-FL GND55G3 GND
8KI-RR A24KI-RL D40KI-RR GND56G3 Vs
9KI-RR C25Vig41KI-RL PSW57NC
10KI-RL A26GND42KI-RL GND58NC
11KI-RL C27KI-FR Vcc43M.L59E/G
12Vbat28KI-FR Vout44G3 Vcc60W. L
13GND29KI-FR PSW45G3 Vout61GND
14GND30KI-FL Vout46NC62GND
15NC31KI-FL Vcc47NC63Rxd
16Vdd32KI-RR Vcc48VSP64GND
NC: NO CONNECTION
System Components
Control Unit, 3 Vertical G-sensors, Lateral G-sensor, 4
Actuators, 4 Adjustable Damping Force Shock
Absorbers, and Warning Lamp.
Control Unit
The Control Unit consists of Adjustable Damping Force
Shock Absorber control circuits, fault detector, and a
fail-safe. It drives the actuator according to the signal
from each sensor.
The Control Unit has a self-diagnosing function which can
indicate faulty circuits during diagnosis.
The Control Unit is mounted in the center of the
instrument panel.
Actuator
Front actuators installed on front shock absorbers and
rear actuator installed inside rear shock absorbers control
damping force of shock absorber by the Control Unit
signal.
Adjustable Damping Force Shock
Absorber
This type shock absorber is used in front and rear
intelligent suspension. According to running condition the
Control Unit changes shock absorber damping force and
obtains good running stability.
Warning Lamp
821R200011Vehicles equipped with the Intelligent Suspension Control
have an amber warning lamp in the instrument panel. The
warning lamp will illuminate if a malfunction in the
Intelligent Suspension Control is detected by the Control
Unit. In case of an important electronic malfunction, the
Control Unit will turnªONº the warning lamp.

INTELLIGENT SUSPENSION3F±5
Vertical G-Sensor
Front G-sensors installed inside front actuators and the
rear G-sensor installed on the rear left frame side detect
the vehicle vertical gravity and send a signal to the Control
Unit.
Lateral G-Sensor
The G-sensor installed inside the Control Unit detects the
vehicle turning speed and sends a signal to the Control
Unit.
Acronyms and Abbreviations
Several acronyms and abbreviations are commonly used
throughout this section:
BATT
Battery
DLC
Data Link Connector
DTC
Diagnostic Trouble Code
FL
Front Left
FR
Front Right
GND
Ground
HARN
Harness
IG
Ignition
PCM
Powertrain Control Module
RL
Rear Left
RR
Rear Right
SW
Switch
W/L
Warning Lamp
Vout
Voltage output
General Diagnosis
General Information
Intelligent Suspension Control troubles can be classified
into two types, those which can be detected by the
warning lamp and those which can be detected as a
vehicle abnormality by the driver.
In either case, locate the fault in accordance with
theªBASIC DIAGNOSTIC FLOWCHARTº and repair.
Please refer to
Section 3 for the diagnosis of mechanical
troubles such as abnormal noise, vehicle pulls, excessive
tire wear, wheel hop and shimmy, shake or vibration.
Service Precautions
Required Tools and Items:

Box Wrench

Special Tool
Some diagnosis procedures in this section require the
installation of a special tool.
J-39200 High Impedance Multimeter
When circuit measurements are requested, use a
circuit tester with high impedance.
Computer System Service Precautions
The Intelligent Suspension Control interfaces directly
with the Control Unit which is a control computer that is
similar in some regards to the Powertrain Control Module.
These modules are designed to withstand normal current
draws associated with vehicle operation. However care
must be taken to avoid overloading any of the Control Unit
circuits. In testing for opens or shorts, do not ground or
apply voltage to any of the circuits unless instructed to do
so by the appropriate diagnostic procedure. These
circuits should only be tested with a high impedance
multimeter (J-39200) or special tools as described in this
section. Power should never be removed or applied to
any control module with the ignition in the ªONº
position.Before removing or connecting battery cables,
fuses or connectors, always turn the ignition switch to
theªOFFº position.
General Service Precautions
The following are general precautions which should be
observed when servicing and diagnosing the Intelligent
Suspension Control and/or other vehicle systems. Failure
to observe these precautions may result in Intelligent
Suspension Control damage.

If welding work is to be performed on the vehicle using
an electric arc welder, the Control Unit connectors
should be disconnected before the welding operation
begins.

The Control Unit connectors should never be
connected or disconnected with the ignitionªONº.
Parts Handling
Be careful when handling the actuator, control unit, or
G-sensor. They should not be dropped or thrown,
because the semi-conductor G-sensor tip damage may
result.

INTELLIGENT SUSPENSION3F±7
It depends below in the case that the code that also,
shows a malfunction place is added.
F03R200002
Legend
(1) Diagnostic Trouble Code 2
(2) Diagnostic Trouble Code 3 + Position Code 2
Position Code
1: Actuator Front RH, G-sensor Front RH
2: Actuator Front LH, G-sensor Front LH
3: Actuator Rear RH, G-sensor Rear
4: Actuator Rear LH, Lateral G-sensor
2. After this, the warning lamp will be OFF for 3.5
seconds and then will flash each DTC.
a. When there are more than 9 flashes this means
that the indicator is constantly flashing, OFF for
4 seconds ON for 0.5 seconds. In this case there
is no DTC stored in memory.
b. When there are less than 9 flashes you will see
DTC codes in ascending order.
CLEAR DTC
Remark: If you clear the DTC (Diagnosis Trouble Codes)
you will not be able to read any codes recorded during the
last Trouble.
Remark: To be able to use the DTC again to identify a
problem you will need to reproduce the fault or the
problem. This may require a new test drive or just turning
the ignition on (this depends on the nature of the fault).
1. Short the Diagnosis Connector C-39 terminal 3 to
terminal 4 or 5 (ground).

IF it is flashing and the flash is 0.5 seconds ON and 4
seconds OFF without interruption, this means that
there is no DTC. The DTCs are already cleared.
350R200002
2. IF a code is flashed, wait until the lamp is flashing.
3. Conduct brake switch ON/OFF 6 or more times on
condition that one operation is within 2 seconds.