engine ISUZU TF SERIES 2004 Workshop Manual

ENGINE SPEED CONTROL SYSTEM (C24SE) 6H-3
4. Remove the accelerator control cable from the
throttle.




LHD MODEL

RTW46AMH000101

Inspection
Check the following items and replace the control
cable if any abnormality is found.
 The control cable should move smoothly.
 The control cable should not be bent or kinked.
 The control cable should not be damage o
r
corrosion.
Installation
1. Install the accelerator control cable to accelerator
control pedal dash panel.
2. Install the accelerator control cable to throttle.
Attach T-END and inner cable to throttle cam o
f
engine.
3. Install accelerator control cable to accelerato
r
bracket.
1) Rotate the ratchet ring in direction an arrow 90

until both white marking are aligned.
2) Confirm marking of outer cap must be uppe
r
side.
3) Slider the lock in direction B.
4) Confirm ratchet ring is locked.

6H-4 ENGINE SPEED CONTROL SYSTEM (C24SE)
MEMO

SHEET METAL 2B-1

SECTION 2B
SHEET METAL

This section includes items of front end sheet metal that are attached by bolts, screws or clips and related
accessory components.
Anticorrosion materials have been applied to the interior surfaces of some metal panels to provide rust resistance.
When servicing these panes, areas on which this material has been disturbed, should be properly recoated with
service-type anticorrosion material.
TABLE OF CONTENTS
PAGE
Engine Hood Assembly ..................................................................................................... 2B- 2
Engine Hood Lock ............................................................................................................. 2B- 5
Front Fender Panel ............................................................................................................ 2B- 7
Radiator Grille .................................................................................................................... 2B- 10
Rear Body ........................................................................................................................... 2B- 11
Body Mounting ................................................................................................................... 2B- 13
Body Dimension.................................................................................................................2B- 19

2B-2 SHEET METAL
ENGINE HOOD ASSEMBLY
REMOVAL AND INSTALLATION




RTW42BLF000101

Removal Steps
Installation Steps


1. Washer nozzle tube
6. Hood seal


2. Hood hinge bolts
5. Hood insulator (Die. Eng. Only)
3. Engine hood
4. Washer nozzle
4. Washer nozzle


3. Engine hood
5. Hood insulator (Die. Eng. Only)


2. Hood hinge bolts
6. Hood seal
1. Washer nozzle tube

SHEET METAL 2B-3



Important Operations - Removal
1. Washer Nozzle Tube

1) Open the hood.
2) Support the hood.
3) Remove the windshield washer nozzle tube.




2. Hood Hinge Bolts



Before removing
the hinges from the engine hood, scribe a
mark showing location of
the hinges to facilitate installation in
the original position.

RTW32BSH000101

Important Operations - Installation
3. Engine Hood


Check the engine hood and fender. (1)




Clearance : 4.0 mm (0.16 in)


Height (step) : Flushness


Adjust clearance with the hinges on the engine hood.











Adjust height (step) with the hood rests (1).






Engine Hood Striker


Apply a light coat of grease to the striker.

2B-4 SHEET METAL


2. Hood Hinge Bolts


Tighten the engine hood hinge fixing bolts to the specified
torque.

Torque N
m(kgf
m/lb
in)
10 (1.0
/ 87)

SHEET METAL 2B-5
ENGINE HOOD LOCK
REMOVAL AND INSTALLATION



This illustration is based on the RHD model.
RTW42BMF000101

Removal Steps
Installation Steps


1. Radiator grille


4. Control cable


2. Engine food lock assembly
3. Hood lock control lever
3. Hood lock control lever


2. Engine food lock assembly


4. Control cable
1. Radiator grille



Important Operations - Removal
1. Radiator Grille
Refer to the Radiator Grille in this section.


2. Engine Hood Lock Assembly

Apply setting marks (1) to the hood lock assembly and the
body prior to removal.

4. Control Cable
Pull out the control cable toward the passenger compartment.

2B-6 SHEET METAL


Important Operations - Installation
4. Control Cable

Reroute the control cable to its original position, and check and
see if the lock assembly and control lever work normally.


2. Engine Hood Lock Assembly

Adjustment
1) Install the engine hood lock assembly (4) and temporaril
y
tighten the bolts securing it.
2) Close the hood.
3) Position the hood so that the stepped portion between the
hood (1) and the fender (2) is precisely 1.5 mm (0.06 in)
high.
4) Final tighten the bolts securing the engine hood lock
assembly.



5) Turn the buffers (3) counterclockwise until the stepped
portion between the hood and the fender disappears.
6) Tighten the hood lock assembly fixing bolts to the specified
torque.

Torque N
m(kgf
m/lb
in)
10 (1.0
/ 87)

GENERAL INFORMATION 0A-5

7. Measurement criteria are defined by the terms "standard" and "limit".

A measurement falling within the "standard" range indicates that the applicable part or parts are serviceable.
"Limit" is an absolute value.

A measurement falling outside the "limit" indicates that the applicable part or parts must be repaired or replaced.
8. Components are parts are listed in the singular form throughout the Workshop Manual.
9. The following directional criteria are used throughout the Workshop Manual:

Front:

The cooling fan side of the engine.
Right:

The right-hand side of the engine viewed from the flywheel.

Left:
The left-hand side of the engine viewed from the flywheel.

Rear:

The flywheel side of the engine.
Cylinder numbers are counted from the front of the engine towards the rear.

The engine's rotation is clockwise viewed from the front of the engine.

0A-6 GENERAL INFORMATION
IDENTIFICATION



CHASSIS NUMBER
The chassis number is stamped on the right-hand side of the
chassis side member under the right door.




VEHICLE IDENTIFICATION PLATE
The vehicle identification plate is attached to the upper face of
the radiator sill in the engine compartment.




BODY AND OPTION IDENTIFICATION
PLATE
The body and option plate shows body style, body serial
number, paint and trim colour combination, paint number,
engine transmissions, axle ratio options and built date. The
built date is defined as 'the date of manufacture' by the
calendar month and year in which the body shell and power
train sub-assemblies are co-joined or moved from the
production line.