engine ISUZU TF SERIES 2004 Workshop Manual

1-52 HEATER AND AIR CONDITIONING
REASSEMBLY


This illustration is based on the 4J engine model
871R30003

Reassembly Steps
1. Compressor

2. Field coil
3. Thermo sensor and lead wire connector
4. Snap ring

5. Pulley assembly
6. Snap ring
7. Drive plate
8. Plain washer

9. Drive prate bolt

1-80 HEATER AND AIR CONDITIONING

BLOWER MOTOR DOES NOT RUN


Replace
YES

Is No.SBF-8 (30A) slow blow fuse OK?

Is heater & A/C relay (X-11) OK?
YES

Is resistor OK?
YES

Is fan control knob (Fan switch) OK?
YES
YES

Check to see if battery voltage is present at
chassis side connector terminal No.C105-1 is there a
battery voltage?

Turn the ignition switch "ON" (Engine is running)

Fan control knob (Fan switch) "ON"

Is blower motor OK?
YES
Poor ground or open circuit either between chassis
side connector terminal No.C105-2 and No.C104-3
or No.B13-1 and body ground No.C-109.
NO
Replace
NO
Replace
NO
NO
Replace control lever
assembly
Replace
NO
NO
Open circuit between
No.SBF-8 (30A) slow blow
fuse and No.C105-1.

1-84 HEATER AND AIR CONDITIONING

f06r300014
CHECKING REFRIGERANT SYSTEM
WITH MANIFOLD GAUGE
Conditions;


Ambient temperature at approx. 30
35
C (86
95
F)


Run the engine at Idling

A/C switch is “ON”


Run the blower motor at “4” (high) position


Temperature control knob sets at “MAX COLD”


Air source selector lever at “CIRC”


Close the all doors
Normal pressures kPa (kg/cm
2 / PSI);
Low-pressure side:
Approx. 127 – 245 (1.3 – 2.5 / 18 – 36)
High-pressure side:
Approx. 1373 – 1670 (14 – 17 / 199 – 242)
Connect the manifold gauge
Low-pressure hose (LOW)  Suction side
High-pressure hose (HI)  Discharge side

HEATER AND AIR CONDITIONING 1-87

MAGNETIC CLUTCH
When the A/C switch and the fan control knob (fan switch) are turned on with the engine running, current flows
through the thermostat and the compressor relay to activate the magnetic clutch.
The air conditioning can be stopped by turning off the A/C switch or the fan control knob (fan switch).
However, even when the air conditioning is in operation, the electronic thermostat, the pressure switch or the ECM
is used to stop the air conditioning temporarily by turning off the magnetic clutch in the prearranged conditions to
reduce the engine load which is being caused by the rise in the engine coolant temperature, and the acceleration of
the vehicle, etc.

1-90 HEATER AND AIR CONDITIONING

MAGNETIC CLUTCH DOES NOT RUN (4JA1L/4JH1-TC)



Replace
YES


Are the A/C thermo (X-15) and heater & A/C (X-11)
and A/C compressor (X-14) relay OK?

Are the No. SBF-8 fuse (30A) and the No. EB-13
(10A) fuses OK
YES


Is the pressure switch (C-24) OK?
YES


Are the A/C switch (B-57) and the fan switch (B-13)
OK?
NO
YES


Is there continuity between the engine harness
connector terminal No.1 (E-3) and engine room harness
connector terminal No.2 (X-14)?

Disconnect the A/C compressor relay.

Turn the ignition switch "ON" (Engine is running)


A/C switch and fan control knob (fan switch "ON")
NO
Replace
NO
Defective switch or insufficient
refrigerant
NO
NO
Does the magnetic clutch
operate?
YES
Replace


Disconnect the magnetic clutch connector.

Is there battery voltage between the engine room harness
connector terminal No.1 (E-3) and ground?
Defective compressor
YESNO
Defective magnetic clutch

HEATER AND AIR CONDITIONING 1-91





Open circuit between the engine
harness connector terminal No.1 (E-3)
and engine room harness connector
terminal No.2 (X-14).
YES


Is there battery voltage between the engine room
harness connector terminal No.1 (X-14) and
ground?
YES


Disconnect the A/C thermo relay.
YES


Is there continuity between the ECM harness
connector terminal No.38 (C-56) and engine
room harness connector terminal No.4 (X-14)?
NO
Open circuit between the No. EB-13
fuse and engine room harness
connector terminal No.1 (X-14).
NO
Open circuit between the engine room
harness connector terminal No.1 (X-
15) and engine room harness
connector terminal No. 3 (X-14).
NO

Is there continuity between the engine room
harness connector terminal No.3 (X-14) and No.1
(X-15)?
YES


Is there continuity between the ECM harness
connector terminal No.30 (C-56) and engine
room harness connector terminal No.2 (X-15)? Open circuit between the engine room
harness connector terminal No.1 (X-
15) and engine room harness
connector terminal No. 3 (X-14).
NO
YES


Is there battery voltage between the engine room
harness connector terminal No.4 (X-15) and
ground?
Open circuit between the ECM
harness connector No. 38 (C-56) and
engine room harness connector
terminal No. 4 (X-14).
NO
YES


Is there continuity between the engine room
harness connector terminal No. 3 (X-15) and the
engine room harness connector terminal No. 1 (C-
24).
Open circuit between the No. EB-13
fuse and engine room harness
connector terminal No. 4 (X-15).
NO


Disconnect the ECM harness connector.


Disconnect the pressure switch?

1-92 HEATER AND AIR CONDITIONING




YES

Disconnect the condenser fan relay connector
condenser fan.
YES


Is there battery voltage between the engine
room harness connector terminal NO.3 (C-
24) and ground? Open circuit between the condenser
fan relay 4JH1TC No.4 (X-6) 4JA1L
No. 3 (X-13) and engine room harness
connector terminal No. 4 (X-14).
NO

Is there continuity between the relay terminal
4JH1TC No. 4 (X-6) 4JA1L No.3 (X-13)and
engine room harness connector terminal No.4
(C-24)?
YES


connect the A/C thermo relay connector.
Open circuit between the No. EB-13
fuse and engine room harness
connector terminal No. 3 (C-24).
NO
YES


Is there battery voltage between the engine
room harness connector terminal No.3 (C-55)
dd?
Open circuit between the engine room
harness connector terminal No. 2 (C-
55) and the engine room harness
connector terminal No. 2 (C-24).
NO
YES


Is there continuity between the engine room
harness connector terminal No.1 (C-55) and
ground (C-109) ? or (cooler only) the short
connector terminal No.3 (B-79) and ground (C-
109
)?
Open circuit between the No. EB-13
fuse and engine room harness
connector terminal No. 3 (C-55).
NO


Disconnect the electronic themostat.


Is there continuity between the engine room
harness connector terminal No. 2 (C-55) and the
engine room harness connector terminal No. 2
(C-24).
Open circuit between and engine room
harness connector terminal No. 3 (X-
15) and the engine room harness
connector terminal No. 1(C-24).
NO

HEATER AND AIR CONDITIONING 1-93



YES


Disconnect the A/C switch.


Is there battery voltage between the chassis side
harness connector terminal No. 6 (B-57) and ground (C-
109)?
Open circuit between the engine room
harness connector terminal No. 1 (C-55) or
(cooler only) the short connector No. 3 (B-
79) and ground (C-109).
NO YES

Is there continuity between the engine room harness
connector (cooler only) terminal No. 4 (C-55) and the
chassis side harness connector terminal No. 11 (B-57).
Open circuit between the engine room
harness connector (cooler only) terminal
No. 4 (C-55) and the chassis side harness
connector terminal No. 11 (B-57).
NO YES

Is there battery voltage between the chassis side
harness connector terminal No. 10 (B-57) and ground?
Open circuit between the chassis side
harness connector No. 1 (B-79) and
chassis side harness connector terminal
No. 10 (B-57).
NO
YES


Is the electronic themostat OK? Open circuit between the No. EB-13 fuse
and the chassis side harness connector
No. 6 (B-57).
NO
YES

Defective ECM Replace electronic thermostat
NO

HEATER AND AIR CONDITIONING 1-95

MAGNETIC CLUTCH DOES NOT RUN


Replace
YES

Are the A/C thermo (X-15), heater & A/C (X-11)
and A/C compressor (X-14) relay OK?


Are the No. SBF 8 fuse (30A) and the No. EB-13
(10A) fuses OK
YES

Is the pressure switch (C-24) OK?
YES


Are the A/C switch (B-57) and the fan switch (B-13)
OK?
NO
YES


Is there continuity between the engine harness
connector terminal No.1 (E-2) and engine room
harness connector terminal No.2 (X-14)?


Disconnect the A/C compressor relay.


Turn the ignition switch "ON" (Engine is running)

A/C switch and fan control knob (fan switch "ON")
NO
Replace
NO
Defective switch or insufficient
refrigerant
NO
NO
Does the magnetic clutch
operate?
YES
Replace


Disconnect the magnetic clutch connector.


Is there battery voltage between the engine room
harness connector terminal No.1 (E-2) and ground?
Defective compressor
YESNO
Defective magnetic clutch

1-96 HEATER AND AIR CONDITIONING




Open circuit between the engine
harness connector terminal No.1 (E-
13) and engine room harness
connector terminal No.2 (X-14).
YES


Is there battery voltage between the engine room
harness connector terminal No.1 (X-14) and
ground?
YES


Disconnect the A/C thermo relay.
YES

Is there continuity between the ECM harness
connector terminal No. 11 (E-61) and engine
room harness connector terminal No.4 (X-14)?
NO
Open circuit between the No. EB-13
fuse and engine room harness
connector terminal No.1 (X-14).
NO
Open circuit between the No.EB-13
fuse and engine room harness
connector terminal No. 3 (X-14).
NO

Is there battery voltage the engine room harness
connector terminal No.3 (X-14) and ground?
YES


Is there continuity between the ECM harness
connector terminal No.31 (E-61) and engine
room harness connector terminal No.1 (X-15)? Open circuit between the ECM
harness connector No. 11 (E-61) and
engine room harness connector
terminal No. 4 (X-14).
NO
YES

Is there battery voltage between the engine room
harness connector terminal No.3 (X-15) and
ground?
Open circuit between the No. EB-13
fuse and engine room harness
connector terminal No. 2 (X-15).
NO
YES

Is there continuity between the engine room harness
connector terminal No. 4 (X-15) and the engine room
harness connector terminal No. 1 (C-24)?
Open circuit between the No. EB-13
fuse and engine room harness
connector terminal No. 3 (X-15).
NO


Disconnect the ECM harness connector.

Disconnect the pressure switch.