display ISUZU TF SERIES 2004 Workshop Manual

11A-24 IMMOBILIZER SYSTEM

5.
When reset is completed, the following screen
shows up.

060R200278

Reset Engine Control Module (Reset ECM)
1.
Select "Body" and "Immobilizer".
2.
Select "Additional Function" and "Reset Engine
Control Module".
3.
The following screen shows up.

060R200289

4.
Confirm the following screen shows up.
5.
Input the security code, then press the soft key o
f
"Not Okay" or "Okay".
6.
The following screen shows up.


7.
Programming is completed.

060R200278

8.
When the procedure is completed waits 10
seconds and then turn the Key on.

The fail lamp begins to flash.
9.
Turn the ignition on, then engine dose not run.
10. Reset is completed.
Erase transponder key
1. Select "Body" and "Immobilizer".
2. Select "Additional Function” and "Erase
Transponder-Keys".
3. See immobilizer status on Tech-2 screen and type
security code. If the status dose not allow the
programming, only immobilizer status is displayed.
4. See illustration of caution.

IMMOBILIZER SYSTEM 11A-25






CAUTION


060R200286






Erase


060R200285

4.
See programming result on display.

Programming Immobilizer Function
Caution:

1)
Do not replace ICU and ECM at the same time
2)
Change ICU at first or ECM and other one
change follows.


1.
Select "Body" and "immobilizer".
2.
Select "Programming" on Tech-2 display.
3.
Check the display, then press the "Confirm" key.

LTW3BASH000401

4.
Install the "Hardware Key" on PC.
5.
Connect RS232 cable to the PC and Tech2.
6.
Turn on the PC, then start software "TIS 2000".
7.
Select "Security Access" in the TIS 2000 screen.

11A-26 IMMOBILIZER SYSTEM

8.
Select "Next" in the TIS 2000 screen and wait a
few seconds.
9.
When programming is enabled (Approved), then
press "close" in the TIS 2000 screen.

(Finish the "TIS 2000" operation.)
10.
Select "Program Immobiliser Function" on Tech-2
display.
11.
The following screen shows up.

060R200289

12.
Confirm the following screen shows up.
13.
Input the security code, then press the soft key o
f
"Not Okay" or "Okay".
14.
Select the engine type then, press "Enter" key.
15.
Input a program option, by moving the cursor on
the selection, then press "Enter" key.


Programming ICU


Programming ECM


Programming ICU and ECM




Programming ICU and ECM

060R200283
Programming ICU
1.
Follow Programming Immobilizer Function steps 1
through 14.
2.
Input a program option, by moving the cursor on
the selection, then pres "Enter" key.

060R200283

3.
Enter the security code.

IMMOBILIZER SYSTEM 11A-27

4.
Input the security code, then press the soft key of
"Okay" or "Not Okay".

060R200284

5.
Enter VIN.
6.
Enter Mechanical key number.
7.
Turn ON ignition.
8.
Select an engine system.
9.
See the programming result.

Tech-2 displays the result of programming as the
following.

Follow those instructions

Selected Programming is not possible due to
wrong System Status!


Immobilizer Not Programmed!


Immobilizer Already Programmed!


ECM Not Programmed!


ECM Already Programmed!
10.
Transponder key must be reprogrammed,
because all transponder information is erased.

When ICU is programmed. See Transponde
r
programming.

Programming ECM
1.
Follow Programming Immobilizer Function steps 1
through 14.
2.
Input a program option, by moving the cursor on
the selection, then pres "Enter" key.

060R200283
3.
Enter the security code.
4.
Input the security code, then press the soft key o
f
"Okay" or "Not Okay".

060R200284

5.
Turn on the Ignition.
6.
Select an Engine system.

11A-28 IMMOBILIZER SYSTEM

7.
See the display of programming result.

Tech-2 displays the result of programming as the
following.

Follow those instructions


Selected Programming is not possible due to
wrong System Status!


Immobilizer Not Programmed!


Immobilizer Already Programmed!

ECM Not Programmed!

ECM Already Programmed!
8.
Transponder key must be reprogrammed,
because all transponder information is erased.

When ICU is programmed. See Transponde
r
programming.
Programming ICU and ECM
1.
Follow Programming Immobilizer Function steps 1
through 14.
2.
Input a program option, by moving the cursor on
the selection, then pres "Enter" key.

060R200283
3.
Enter the security code.





4.
Input the security code, then press the soft key o
f
"Okay" or "Not Okay".

060R200284

5.
Input the security code.
6.
Enter VIN.
7.
Enter Key No.
8.
Select an engine system.

See programming result display and follow
instructions of the display.
9.
Transponder key must be reprogrammed,
because all transponder information on ICU is
erased when ICU is programmed. See
Transponder programming.
10.
Follow Programming ECM steps 2 through 8.
Transponder program
1.
Select "Body" and "Immobilizer".
2.
Select "Programming" and "Program Transponder-
Keys".

(Follow Programming Immobilizer Function steps 1
through 14.)
3.
See immobilizer status on Tech-2 screen, and
enter security code. If the status does not allow the
programming, only immobilizer status is displayed.

IMMOBILIZER SYSTEM 11A-29

4.
Insert Non-programmed Transponder-key and
press soft key of "Confirm".

060R200288

5.
"Turn On ignition key", is displayed if the ignition is
off.
6.
The transponder status is displayed if the status
does not allow the programming.
7.
When programming starts "Programming
Transponder - key!" is displayed.
8.
Turn off Ignition key.
9.
Turn On Ignition key.
10.
If the programming was not successful, the
transponder status is only displayed.
11.
To program more illustration press soft key.

RUW38SH000601

12.
See programming result.

11A-34 IMMOBILIZER SYSTEM

IMMOBILIZER SYSTEM CHECK
Step Action Value(s) Yes No
1 1. Key position is "ON," engine "OFF."
2. Observe the check engine lamp.
Note: When a key switch is turned ON, check engine
lamp will turn on and a check engine lamp will be
turned off after a few seconds.
Is the check engine lamp "ON"? 
Go to Step 2
Go to "No
Immobilizer
warning lamp"
2 1. Key position is "ON," engine "OFF."
2. Observe the check engine lamp.
Note: When a key switch is turned ON, check engine
lamp will turn on and a check engine lamp will be
turned off after a few seconds.
Is the check engine lamp "OFF"?
(Check engine lamp does not flash) 
Go to Step 3
Go to
"Immobilizer
warning lamp on
steady"
3 1. Key position is "OFF."
2. Install a scan tool.
3. Key position is "ON."
4. Attempt to display immobilizer data with the scan
tool.
Does the scan tool display immobilizer data? 
Go to Step 9
Go to Step 4
4 1. Key position is "OFF," disconnect the immobilizer
control unit (ICU).
2. Check the DLC (Data Link Connector) circuit for
an open, short to ground, or short to voltage.
Also, check the DLC ignition feed circuit for an
open or short to ground and the DLC ground
circuit for an open.
Was a problem found? 
Go to Step 5
Go to Step 6
5 Repair or replace the DLC (Data Link Connector)
circuit.
Was the action complete? 
Go to Step 3 
6
1. Check the ICU circuit for an open, short to ground,
or short to voltage. Also, check the ICU ignition
feed circuit for an open or short to ground and the
ICU ground circuit for an open.
2. If a problem is found, repair as necessary.
Was a problem found? 
Go to Step 7
Go to Step 8
7 Repair or replace the ICU ignition feed and ground
circuits.
Was the action complete? 
Go to Step 3 
8 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the immobilizer data by the scan tool.
Was the action complete? 
Go to Step 3 
9 Select "Display DTCs" with the scan tool.
Are any DTCs stored? 
Go to Step 10
Go to Step 13

IMMOBILIZER SYSTEM 11A-35

Step Action Value(s) Yes No
10 Review and record for scan tool Failure Records data
and DTCs.
Was the action complete? 
Go to Step 11 
11 Following the DTC is stored.
Are there DTC B0001 or B0055 stored?
Go to applicable
DTC table after
Go to Step 12 Go to Step 12
12 Clear the DTCs by "Clear the Information "with scan
tool.
Did the DTCs Cleared? 
Go to Step 12 
13 Select "Display DTCs" with the scan tool.
Are any DTCs stored? 
Go to applicable
DTC table Go to Step 14
14 1. Key position is "ON," engine "OFF."
2. Observe the check engine lamp.
Note: If a key switch is turned ON, check engine lamp
will turn on and a check engine lamp will be turned off
after a few seconds.
Is the check engine lamp "flash"? 
Go to Step 15
Go to Step 20
15 Check the engine control system.
If a problem is found, repair as necessary.
(Refer to section 6E: system check and DTCs)
IMPORTANT:
The replacement ECM must be
programmed the immobilizer data by scan tool.
(Except 4JA1-L Engine)
Was the action complete? 
Go to Step 16 
16 Check the key.
Is a key peculiar to a vehicle? 
Go to Step 18
Go to Step 17
17 Change into a peculiar key.
IMPORTANT:
If replace the key,
after replace lock
cylinders, perform the following below the items.

Replace the keys and key cylinders.

Program the immobilizer system.
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 18 
18 Check the immobilizer programming functions.


Immobilizer control unit (ICU).


Engine control module (ECM).


Transponder (Key).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 19

19 Operate the DTCs by "Clear the Information" with
scan tool.
Was the action complete? 
Go to Step 20 
20 Attempt to start the engine.
Did the engine start? 
System OK
Refer to
Diagnostic Aids

11B – 2 ANTITHEFT SYSTEM
Pin-outs ......................................................................................................................11B – 21
Pin- Assignment ........................................................................................................ 11B – 22
lmportant information on Programming .................................................................... 11B – 23
Security code ............................................................................................................. 11B – 23
Entering a code ......................................................................................................... 11B – 23
Tech-2 Scan Tool............................................................................................................ 11B – 24
Tech-2 Features ......................................................................................................... 11B – 25
Getting Started ......................................................................................................... 11B – 25
Operating Procedure................................................................................................. 11B – 26
Menu ..........................................................................................................................11B – 27
DTC ............................................................................................................................. 11B – 27
Clear DTC Information .............................................................................................. 11B – 27
Tech-2 Data Display................................................................................................... 11B – 27
Actuator Test ............................................................................................................. 11B – 27
Unlock / Lock Test..................................................................................................... 11B – 27
Arm / Disarm Signal Test ......................................................................................... 11B – 28
Horn Signal Test ........................................................................................................ 11B – 28
Turn Signal Test......................................................................................................... 11B – 28
Theft LED Test ........................................................................................................... 11B – 28
Programming............................................................................................................. 11B – 29
Erase remote keys..................................................................................................... 11B – 29
Program Remote Keys .............................................................................................. 11B – 30
ProgramAntitheft Waring......................................................................................... 11B – 31
Program Country Code ............................................................................................. 11B – 32
Program Vehicle Options.............................................................................................. 11B – 33
Tech-2 Data List ......................................................................................................... 11B – 34
DIAGNOSIS .................................................................................................................... 11B – 35
Diagnostic procedure................................................................................................ 11B – 35
Clearing Diagnostic Trouble Codes ......................................................................... 11B – 35
Verifying Vehicle Repair............................................................................................ 11B – 35
Diagnostic Aids ......................................................................................................... 11B – 35
Check the condition for system parts ..................................................................... 11B – 35
Check the Electro-Magnetic Interference (EMI) ..................................................... 11B – 35
Check the other items .............................................................................................. 11B – 35
Check the operation.................................................................................................. 11B – 35
Diagnostic Trouble Code (DTC) list.......................................................................... 11B – 36
Antitheft System Check ........................................................................................... 11B – 37
No Antitheft Lamp .................................................................................................... 11B – 38
DTC13 Security code not yet programmed ............................................................ 11B – 39
DTC14 No remote key programmed ....................................................................... 11B – 40
DTC16 Door lock actuators short circuit to ground ............................................... 11B – 41

ANTITHEFT SYSTEM 11B – 25
Tech-2 Features
1. Tech-2 is a 12volt system. Do not apply 24
volts.
2. After connecting and/or installing the vehicle
communication interface (VCI) module, PCMCIA
card and data link connector (DLC) to the Tech-
2, connect the tool to the vehicle DLC.
3. Make sure the tech-2 is OFF when removing or
installing the PCMCIA card.
4. The Tech-2 has the capability of two or three
snapshot.
5. The PCMCIA card is sensitive to magnetism and
static electricity, so care should be taken in the
handling of the card.
6. Always return to the Main Menu by pressing
the EXIT key several times before shutting
down.
7. To clear diagnostic trouble codes (DTCs), open
Application Menu and press “Clear DTC”.
Getting Started
Before operating the Isuzu PCMCIA card with the
Tech-2, the following steps must be performed:
1. The Isuzu System PCMCIA card inserts into the
Tech-2.
2. Connect the SAE 16/19 adapter to the DLC
cable.
3. Connect the DLC cable to the Tech-2.
4. Mark sure the vehicle ignition is off.
5. Connect the Tech-2 SAE 16/19 adapter to the
vehicle DLC.
6. Turn the vehicle ignition (key) switch.
7. Power the Tech-2 ON and verify the Tech-2
power up display.
8 7 6 5 4 3 2 1
16 15 14 13 12 11 10 9
060R300015
Press (ENTER) To Continue
060RW009