switch ISUZU TF SERIES 2004 Workshop Manual

UNIT REPAIR (JR405E) 7A4-27

Spring specifications
No. Valve nomenclature Free length
(mm / in) Outside
diameter (mm
/ in) Linear
diameter (mm
/ in) Number of
coils
14 Pressure relief 49.0 / 1.929 7.6 / 0.299 1.1 / 0.043 17.3
15 Pressure regulator 30.5 / 1.201 14.0 / 0.551 1.4 / 0.055 5.7
16 Low and reverse brake fail (A) 22.0 / 0.866 7.0 / 0.276 0.6 / 0.024 10.0
17 Fail 23.0 / 0.906 11.0 / 0.433 0.5 / 0.020 13.2
18 Low and reverse brake amp 19.5 / 0.768 7.9 / 0.311 0.5 / 0.020 6.9
19 2 – 4 brake fail (A) 24.8 / 0.976 8.5 / 0.335 0.9 / 0.035 7.8
20 Low clutch amp (B) 26.0 / 1.024 11.0 / 0.433 0.5 / 0.020 6.9
21
Torque converter relief More than 47.2
/ 1.858 9.2 / 0.362 1.6 / 0.063 20.2
22 2 – 4 brake solenoid accumulator 31.4 / 1.236 9.8 / 0.386 1.3 / 0.051 9.3
23 High clutch accumulator 51.0 / 2.008 6.5 / 0.256 0.8 / 0.031 23.5

Oil pressure switch
Apply compressed air (392 kPa/4.0 kg/cm2) to the oil pressure
switch to check the oil pressure switch continuity between the
connector and screw.






244L300011

Oil temperature sensor (harness assembly)
Check the oil temperature sensor resistance between harness
terminals 7 and 6 (ground).

Oil temperature sensor resistance: 2,400




2,600 ohms
(20
 )


Solenoid
Measure the resistance of each solenoid.

Resistance:
Brown connector – 3.0
 3.4 ohms (20
 C)
Gray connector – 12.0
 13.2 ohms (20
 C)
White connector – 12.2
 13.4 ohms (20
 C)

Reassembly steps

Coat the parts with ATF before installing them.

Install the control valve to the control valve lower body.

Install the oil filter to the control valve lower body.

7A4-54 UNIT REPAIR (JR405E)

TRANSMISSION CASE

02CASE-BK06
Legend
1. Transmission case
2. Spring pin (slender)
3. Spring pin (fat)
4. Manual plate
5. Detent spring


6. Parking rod
7. Manual shaft
8. Oil seal
9. Inhibitor switch

7A4-82 UNIT REPAIR (JR405E)
244L300001


21.Oil pan

Install a new gasket and the oil pan.

Tighten the bolts to the specified torque.
Torque: 8 N 


m (69 Ib 


in)

47INH-SW01

22.Inhibitor switch

Secure the inhibitor switch (1) by hand-tightening the 2
bolts.

Use the inhibitor switch set plate to align the neutral
holes (manual shaft and inhibitor switch).
Turn the inhibitor switch to adjust it.
Inhibitor switch set plate: 5-8840-2763-0
NOTE:
Inhibitor switch adjustment is very important.
If the inhibitor switch is not correctly adjusted, the
automatic transmission will not function normally.

Tighten the 2 inhibitor switch bolts to the specified
torque.

UNIT REPAIR (JR405E) 7A4-87
ILLUSTRATION PART NO. PART NAME


5-8840-2763-0


Inhibitor Switch Set Plate