lock ISUZU TF SERIES 2004 Workshop Manual

ON-VEHICLE SERVICE (AW30–40LE) 7A3-1
TRANSMISSION
ON-VEHICLE SERVICE (AW30–40LE)
CONTENTS

Service Precaution .................................................
7A3-2
Location of Clutch, Brake, One-Way Clutch
and Solenoid ........................................................
7A3-3
Operation of Clutch, Brake and One-Way
Clutch ....................................................................
7A3-4
Trnasmission Indentification ..............................
7A3-4
Speed Change and Lock-Up Pattern ...............
7A3-5
Overdrive and Lock-Up Operating
Conditions ............................................................
7A3-5
Diagnosis .................................................................
7A3-6
Basic Troubleshooting ........................................
7A3-6
Manual Shifting Test ...........................................
7A3-12
Stall Test ..............................................................
7A3-12
Time Lag Test .....................................................
7A3-13
Hydraulic Test ......................................................
7A3-14
Road Test .............................................................
7A3-15
Shift Pont Chart and Lock-Up Point Chart ..........
7A3-19
Shift Pont Chart ...................................................
7A3-19
Lock-Up Point Chart ...........................................
7A3-20
Transmission Fluid Level and Condition .............
7A3-21
Inspection .............................................................
7A3-21
ATF Replacement ..................................................
7A3-22
Inspection .............................................................
7A3-22
Neutral Start Switch (Mode Switch) .....................
7A3-23
Inspection .............................................................
7A3-23
Removal ...............................................................
7A3-23
Installation ............................................................
7A3-23
Brake Signal ............................................................
7A3-24
Inspection .............................................................
7A3-24
Input and Output Revolution Sensor ....................
7A3-25
Inspection .............................................................
7A3-25
Pattern Select Switch .............................................
7A3-25
Inspection .............................................................
7A3-25
Solenoid ...................................................................
7A3-26
Inspection .............................................................
7A3-26

ATF Temperature Sensor ......................................
7A3-27
Inspection .............................................................
7A3-27
Select Lever ....................................................... 7A3-28 Remove or Disconnect .......................................
7A3-28
Install or Connect .................................................
7A3-29
Shift Cable ......................................................... 7A3-31
Remove or Disconnect .......................................
7A3-31
Install or Connect .................................................
7A3-32
Torque specifications ..........................................
7A3-33
Transmission Control Module (TCM) ...................
7A3-34
Removal ................................................................
7A3-34
Installation .............................................................
7A3-34
Shift Solenoid and Lock-Up Solenoid ...................
7A3-35
Removal ................................................................
7A3-35
Installation .............................................................
7A3-36
Valve Body Assembly and Pressure Control Solenoid .................................................
7A3-37
Removal ................................................................
7A3-37
Installation .............................................................
7A3-39
Rear Oil Seal (Adapter Housing, 4

4) .................
7A3-40
Removal ................................................................
7A3-40
Installation .............................................................
7A3-40
Rear Oil Seal (Extension Housing, 4
2) ..............
7A3-41
Removal ................................................................
7A3-41
Installation .............................................................
7A3-41
Transmission Assembly .........................................
7A3-42
Transmission and Associated Parts .................
7A3-42
Removal ................................................................
7A3-43
Installation .............................................................
7A3-46
Major Components ..............................................
7A3-50

7A3-2 ON-VEHICLE SERVICE (AW30 –40LE)

Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFE
R
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.


CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, o
r
other corrosion inhibitors) on threaded fasteners o
r
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-3

Location of Clutch, Brake, One-Way Clutch and Solenoid

RUW37ALF000201

Legend
(8) One-way clutch (No.2) (F–2)
(1) Overdrive direct clutch (C–0) (9) Shift solenoid (S–1)
(2) Overdrive brake (B–0) (10) Shift solenoid (S–2)
(3) Direct clutch (C–2) (11) One-way clutch (No.1) (F–1)
(4) Second coast brake (B–1) (12) Pressure control solenoid (STH)
(5) Forward clutch (C–1) (13) Lock-up solenoid (SL)
(6) Second brake (B–2) (14) Overdrive one-way clutch (F–0)

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-5

Speed Change and Lock-Up Pattern
If you select a speed as shown below by specifying
respective positions of transmission shift lever, transfe
r
switch and pattern select switch, the transmission
control computer controls speed change and lock-up
operations based on the specified pattern in accordance
with the degree of throttle opening and vehicle speed.
Pattern select sw. position Transmission shift position


D 3 2 L
NORMAL, POWER 1st 
[2nd] 
[3rd] 
[O/D] 1st 
[2nd] 
[3rd] 1st 
2nd
(3rd) 1st
(2nd)
3rd START 3rd fixing — —

[ ]: The lock-up operation is available.
( ): Transmission is shifted at high speed to prevent overrun.


Overdrive and Lock-Up Operating Conditions
The overdrive and lock-up clutch operate if the following
conditions are satisfied.
Overdrive Lock-up clutch
Shift pattern position
NORMAL NORMAL
Transmission shift position
D range 
Brake lamp switch
— OFF
Throttle opening
Fully closed Except fully closed
Accelerator About 52 km/h (32 mph) or more 2nd: About 76 km/h (47 mph) or
more
Vehicle speed Deceleration About 42 km/h (26 mph) or more 3rd: About 56 km/h (35 mph) or more
O/D: About 67 km/h (42 mph) or
more

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-15

Measure Line Pressure
1. Fully apply the parking brake and chock the four
wheels.
2. Start the engine and check idling rpm.
3. Shift into “D" range, step down strongly on the brake
pedal with your left foot and, while manipulating the
accelerator pedal with the right foot, measure the
line pressures at the engine speeds specified in the
table.
4. In the same manner, perform the test in “R" range.


Line pressure kPa (kg/cm2/psi) Engine
speed “D" range “R" range
Idling 323 – 382
(3.3 – 3.9/47 – 55) 500 – 598
(5.1 – 6.1/73 – 87)
Stall 1,137 – 1,274 (11.6–13.0/165–185) 1,499 – 1,833
(15.3–18.7/218–266)
Evaluation
1. If the measured values at all ranges are higher than
specified:

Pressure control solenoid defective
 Primary regulator valve defective
2. If the measured values at all ranges are lower than
specified:

Primary regulator valve defective
 Oil pump defective
 Pressure control solenoid defective
3. If pressure is low in “D" range only:

“ D" range circuit fluid leakage
4. If pressure is low in “R" range only:

“ R" range circuit fluid leakage
Road Test
NOTE: Perform the test at normal operation fluid
temperature (50 – 80 
C or 122 – 176 
F).
“D" Range Test in “NORMAL", and
“POWER" Pattern Ranges
Shift into the “D" range and hold the accelerator pedal
constant at the 50% and 100% throttle valve opening
positions.
Push in one of the pattern selector buttons and check
the following:

1. 1 –2, 2 –3, 3 –OD and lock-up, up-shifts should take
place, and shift points should conform to those
shown in the automatic shift diagram.


RUA370MH000101




RUA37ASH000101

7A3-16 ON-VEHICLE SERVICE (AW30 –40LE)

Evaluation
i. If there is no 1 
2 upshift:

Solenoid S2 is stuck
 1 –2 shift valve is stuck
ii. If there is no 2 
3 upshift:

Solenoid S1 is stuck
 2 –3 shift valve is stuck
iii. If there is no 3 
OD upshift (throttle valve opening
1/2):

Solenoid S2 is stuck
 3 –OD shift valve is stuck
iv. If the shift point is defective: Refer to TROUBLESHOOTING CHART in this
section.
v. If the lock-up is defective: Refer to TROUBLESHOOTING CHART in this
section.
2. In the same manner, check the shock and slip at the 1 
2, 2 
3 and 3 
OD upshifts.
NOTE: Drive the vehicle on level ground.
Evaluation
If the shock is excessive:
Refer to TROUBLESHOOTING CHART in this section.
3. Run at “D" range lock-up or OD gear and check fo
r
abnormal noise and vibration.
NOTE: The check for the cause of abnormal noise and
vibration must be made with extreme care as it could
also be due to loss of balance in the propeller shaft,
differential, the torque converter, etc. or insufficient
bending, rigidity, etc. in the power train.



RUW37ASH000201

4. While running in “D" range, 2nd, 3rd gears and OD,
check to see that the possible kick-down vehicle
speed limits for 2 1, 3 1, 3 2, OD 3 and
OD 
2 kick-downs conform to those indicated on
the automatic shift diagram.



RUW37AMH000101
5. Check for abnormal shock and slip at kick-down.
6. While running in “D" range, OD gear or “lock-up",
shift to “2" and “L" ranges and check the engine
braking effect at each of these ranges.
7. Also check to see that downshift is made from 3 
2
or from OD to 3 and then to 2 immediately and that
2 
1 downshift point is within the limits shown in the
diagram when tested by releasing the accelerato
r
pedal and shifting into position of “L" while driving in
the third gear or in overdrive.

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-17

Evaluation
i. If there is no engine braking effect in the “2" range:

Second coast (No.1) brake is defective.

ii. If there is no engine braking effect in the “L" range:

First and reverse (No.3) brake is defective.






RUW37ASH000301
iii. Also check to see that downshift is made from 3 2
or from OD to 3 and then to 2 immediately and that
2 
1 downshift point is within the limits shown in the
diagram when tested by releasing the accelerato
r
pedal and shifting into “L" position while driving in
the third gear or in overdrive.



RUW37ASH000401

“ 2" Range Test
Shift into “2" range and, while driving with the
accelerator pedal held constantly at the specified point
(throttle valve opening 50% and 100%), push in one o
f
the pattern selectors (only for 4
4) and check on the
following points.
1.
At each of the above throttle openings, check to see
that the 1 
2 upshift takes place and that the shift
points conform to those shown on the automatic
shift diagram.
NOTE: There is no OD and no lock-up in the “2" range.


RTW46ASH000301

2. While running in the “2" range and 2nd gear,
release the accelerator pedal and check the
engine's braking effect.
3. Check for 2 
1 downshift and abnormal noise at
acceleration and deceleration, and for shock at
upshift and downshift.






RUW37ASH000501

7A3-18 ON-VEHICLE SERVICE (AW30 –40LE)

“ L" Range Test
1. While running above 80 km/h (50 mph) in the “D"
range, release your foot from the accelerator pedal
and shift into the “L" range.
Then check to see that the 2 
1 downshift occurs at
the specified point shown on the automatic shift
diagram.



RUW37ASH000601
2. While running in the “L" range, check to see that
there is no upshift to 2nd gear.
3. While running in the “L" range, release the
accelerator pedal and check the engine braking
effect.
4. Check for abnormal noise during acceleration and deceleration.







RUW37ASH000701

“ R" Range Test
Shift into the “R" range and, while starting at full throttle,
check for slipping.




RUW37ASH000801
“ P" Range Test
Stop the vehicle on a grade (more than 9%) and afte
r
shifting into the “P" range, release the parking brake.
Then check to see that the parking lock pawl holds the
vehicle in place.

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-19

Shift Point Chart and Lock-Up Point Chart
Shift Point Chart
(H2, H4)
(REAR AXLE RATIO: 4.555)
(RADIUS OF TIRE: 0.350m)
“ NORMAL" mode
Up shift
km/h (mph)

Range Throttle Opening 1 
 

2 2 
 

3 3 
 

4
Fully opened 48 – 54 (30 – 34) 104 – 110 (65 – 68) 177 – 183 (110 – 114)D
Half throttle 32 – 38 (20 – 24) 59 – 65 (37 – 40) 114 – 120 (71 – 75)
Fully opened 48 – 54 (30 – 34) 104 – 110 (65 – 68) — 3
Half throttle 32 – 38 (20 – 24) 59 – 65 (37 – 40) —
Fully opened 48 – 54 (30 – 34) — — 2
Half throttle 32 – 38 (20 – 24) — —

Down shift km/h (mph)

Range Throttle Opening 1 
 

2 2

 

3 3

 

4
Fully opened 37
– 43 (23 – 27) 94 – 100 (58 – 62) 155 – 161(96 – 100)
Half throttle 15 – 21 (9 – 13) 33 – 39 (21 – 24) 65 – 71 (40 – 44) D
Fully closed 9 – 15 (6 – 9) 20 – 26 (12 – 16) 39 – 45 (24 – 28)
Fully opened 37 – 43 (23 – 27) 94 – 100 (58 – 62) —
Half throttle 15 – 21 (9 – 13) 33 – 39 (21 – 24) — 3
Fully closed 9 – 15 (6 – 9) 20 – 26 (12 – 16) —
Fully opened 37 – 43 (23 – 27) 94 – 100 (58 – 62) —
Half throttle 15 – 21 (9 – 13) 94 – 100 (58 – 62) — 2
Fully closed 9 – 15 (6 – 9) 94 – 100 (58 – 62) —
L — 37 – 43 (23 – 27) — —
“ POWER" mode
Up shift
km/h (mph)

Range Throttle Opening 1 
 

2 2 
 

3 3 
 

4
Fully opened 48 – 54 (30 – 34) 104 – 110 (65 – 68) 177 – 183 (110 – 114)D
Half throttle 38 – 44 (24 – 27) 74 – 80 (46 – 50) 128 – 134 (80 – 83)
Fully opened 48 – 54 (30 – 34) 104 – 110 (65 – 68) — 3
Half throttle 38 – 44 (24 – 27) 74 – 80 (46 – 50) —
Fully opened 48 – 54 (30 – 34) — — 2
Half throttle 38 – 44 (24 – 27) — —

7A3-20 ON-VEHICLE SERVICE (AW30 –40LE)

Down shift km/h (mph)

Range Throttle Opening 1 
 

2 2

 

3 3

 

4
Fully opened 39
– 45 (24 – 28) 94 – 100 (58 – 62) 155 – 161(96 – 100)
Half throttle 21 – 27 (13 – 17) 50 – 56 (31 – 35) 95 – 101 (59 – 63) D
Fully closed 13 – 19 (8 – 12) 24 – 30 (15 – 19) 47 – 53 (29 – 33)
Fully opened 39 – 45 (24 – 28) 94 – 100 (58 – 62) —
Half throttle 21 – 27 (13 – 17) 50 – 56 (31 – 35) — 3
Fully closed 13 – 19 (8 – 12) 24 – 30 (15 – 19) —
Fully opened 39 – 45 (24 – 28) 94 – 100 (58 – 62) —
Half throttle 21 – 27 (13 – 17) 94 – 100 (58 – 62) — 2
Fully closed 13 – 19 (8 – 12) 94 – 100 (58 – 62) —
L — 39 – 45 (24 – 28) — —

“3rd START" mode
km/h (mph)
Derange, winter mode ON
OFF 32 – 38 (20 – 24)
Lock-Up Point Chart
(H2, H4)
(REAR AXLE RATIO: 4.555)
(RADIUS OF TIRE: 0.350m) km/h (mph)
Throttle Opening: 20 %
Lock-up ON Lock-up OFF

Range
A/T Mode
3rd 4th 3rd 4th
NORMAL 53 – 59 (33 – 37) 64 – 70 (40 – 43) 45 – 51 (28 – 32) 60 – 66 (37 – 41)
D POWER 78 – 84 (49 – 52) 81 – 87(50 – 54) 68 – 74 (42 – 46) 73 – 79 (45 – 49)

Lock-up points in 2nd are following figures regardless
of throttle opening, whether NORMAL or POWER
mode.
Lock-up ON: 73 – 79 km/h (45 – 49 mph)
Lock-up OFF: 68 – 74 km/h (42 – 46 mph)