lock ISUZU TF SERIES 2004 Workshop Manual
[x] Cancel search | Manufacturer: ISUZU, Model Year: 2004, Model line: TF SERIES, Model: ISUZU TF SERIES 2004Pages: 4264, PDF Size: 72.63 MB
Page 3717 of 4264
TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-37
DTC P0602 (FLASHING CODE 63) Transmission Control Module (TCM)
Programming Error
Circuit Description
The Service Programming System (SPS) updates the
flash calibration files that are stored in a Transmission
Control Module (TCM). The calibration file
custom-tailors a module to a certain vehicle. The
calibration file contains data for things such as spark
curves and fuel control. When troubleshooting a
driveability problem, diagnosis may call fo
r
reprogramming the controller with newer calibration
information to correct a customer concern and Vehicle
Identification Number (VIN).
Condition for setting the DTC
When the TCM is not written VIN No.
Action Taken When The DTC Sets
DTC stored.
Conditions For Clearing The DTC
The DTC can be cleared from the TCM history by
using a scan tool.
The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.
After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids
DTC P0602 is indicated when the TCM does not written
VIN No. A security lock is performed by SPS. And not
replace the TCM when DTC P0602 can repair by SPS.
Page 3718 of 4264
7A2-38 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)
DTC P0602 (FLASHING CODE 63) Transmission Control Module (TCM)
Programming Error
Step Action Value(s) YES NO
1
Was the “On-Board Diagnostic (OBD) System Check"
performed? — Go to Step 2 Go to OBD
System Check
2
1. Install the scan tool.
2. Key “ON".
3. Check the Vehicle Identification Number (VIN) by
the scan tool.
Is VIN on the scan tool same as VIN of vehicles? — Go to Step 4 Go to Step 3
3 Write a VIN by the scan tool. (Refer to SPS for
procedure.)
Is the action complete? — Go to Step 4 —
4 Clear the DTC P0602 by the scan tool.
Is the action complete? — Go to Step 5 —
5 Perform the SPS and perform security lock. (Refer to
SPS for procedure)
Is the action complete? — Go to Step 6 —
6 Recheck the DTC by the scan tool.
1. Key “OFF".
2. Wait a few seconds.
3. Key “ON".
4. Review and record scan tool data.
5. Operate the vehicle with in scan tool data.
Is the action complete? — Go to Step 7 Verify repair
7 Replace the TCM.
Important:
The replacement TCM must be
programmed. (Refer to SPS for procedure.)
Is the action complete? — Verify repair —
Page 3729 of 4264
TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-49
DTC P0717 (FLASHING CODE 14) Input Speed Sensor Signal Error
MAW060MF001501
Circuit Description
Input revolution information is provided to TCM by the
input revolution sensor. This sensor is located in the
transmission case.
The input revolution sensor is an electromagnetic pulse
pickup type that generates a speed signal according to
the revolution of the transmission OD direct clutch
drum. As a result, the sensor sends a sine wave signal
(AC) to the TCM, which converts this sine wave signal
(pulse voltage) to a RPM signal.
Condition for setting the DTC
The TCM detects following conditions at 1000
times continuously.
When the TCM detects following conditions at the
same time.
When output speed is over 775 rpm (16 mph) at
gear position is 1st or 2nd or 3rd.
Input speed signal is no pulse while output speed
signal are 12 pulses.
OR
When the TCM output 2nd gear.
The TCM detects no pulse of input speed senso
r
circuit signal after 3.5 sec.
(detection time: 0.03 sec at vehicle speed is 36 mph)
Action Taken When The DTC Sets
No engine torque control.
No line pressure control.
No lock-up control.
No slope control.
Check Trans ON.
DTC stored.
No detect DTC P0722.
Conditions For Clearing The DTC
The DTC can be cleared from the TCM history by
using a scan tool.
Page 3732 of 4264
7A2-52 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)
DTC P0722 (FLASHING CODE 11) Output Speed Sensor Signal Error
RTW37AMF000501
Circuit Description
Vehicle speed information is provided to the TCM by
the output revolution sensor. This sensor is located in
the transmission adapter housing.
The output revolution sensor is an electromagnetic
pulse pickup type that generates a speed signal
according to the revolution of the transmission output
shaft. As a result, the sensor sends a sine wave signal
(AC) to the TCM, which converts this sine wave signal
(pulse voltage) to a RPM signal.
Condition for setting the DTC
The TCM detects following conditions at 500 times
continuously.
(When gear positions are 1st, 2nd and 3rd.)
When the TCM detects following conditions at the
same time.
Output speed signal is no pulse while input speed
signal are 45 pulses.
(Detection time, 1st: 0.031 sec, 2nd: 0.057 sec, 3rd:
0.087 sec, at vehicle speed is 38 mph.)
Action Taken When The DTC Sets
The TCM uses input speed sensor as a vehicle
speed.
No squat control.
No engine torque control.
No line pressure control.
No use 4th gear.
No lock-up control.
No slope control.
Check Trans ON.
DTC stored.
No reverse lockout control.
Conditions For Clearing The DTC
The DTC can be cleared from the TCM history by
using a scan tool.
Page 3735 of 4264
TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-55
DTC P0743 (FLASHING CODE 33) Torque Converter Clutch Electrical
RUW37ALF000601
Circuit Description
The lock-up solenoid SL of the torque converter clutch
(TCC) controls the lock-up clutch by a signal according
to the lock-up range judgment of the TCM when the
vehicle runs.
This function can improve the fuel consumption to
almost the same extent as the manual transmission.
The lock-up solenoid SL is put into B+ by the TCM, so
that the solenoid is actuated with the result of lock-up.
Condition for setting the DTC
The TCM detects following conditions both "Condition
1" and "Condition 2" occur 2 times or more than it.
Condition 1 ("GND short"):
Voltage at connector pin is 0V for 0.3 sec
continuously when solenoid is “ON".
Condition 2 ("Open or IG short"):
Voltage at connector pin is ignition voltage for 0.5
sec continuously when solenoid is “OFF".
Action Taken When The DTC Sets
No lock-up control.
The TCM fixes to 1st gear when the vehicle speed is
less than 6 mph.
Check Trans ON.
DTC stored.
Page 3738 of 4264
7A2-58 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)
DTC P0748 (FLASHING CODE 35) Pressure Control Solenoid Electrical
RTW37ALF000601
Circuit Description
The pressure control solenoid is a PWM duty control
solenoid located in the valve body.
The pressure control solenoid is a TCM-controled
device used to regulate transmission throttle pressure
by energizing current from the TCM.
Condition for setting the DTC
The TCM detects following "Condition 1" and "Condition
2".
Condition 1("Ignition short"):
When the TCM detects following condition for 0.5
sec continuously.
Monitor A/D value is more than 1000 (1.36A).
Condition 2("Open or GND short"):
When the TCM detects following condition for 70
msec continuously.
Monitor A/D value is less than 15 (20mA).
Action Taken When The DTC Sets
No squat control.
No line pressure control.
No lock-up control.
No slope control.
Check Trans ON.
Page 3742 of 4264
7A2-62 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)
Action Taken When The DTC Sets
The TCM operates shifting as following pattern.
Normal Fail S1 S2
1 3 - on
2 3 - on
3 3 - on
4 4 - off
No squat control.
No engine torque control.
No line pressure control.
No lock-up control.
No slope control.
Check Trans ON.
DTC stored.
No detect DTC P0722
No detect DTC P0717
Conditions For Clearing The DTC
The DTC can be cleared from the TCM history by
using a scan tool.
The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.
After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids
Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.
When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.
DTC P0753 (FLASHING CODE 31) Shift Solenoid S1 Electrical
Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2
1. Install the scan tool.
2. Key “ON".
3. Review and record scan tool data.
4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P0753? — Go to Step 3 Refer to
Diagnostic Aids
3
1. Key “ON", engine run.
2. Place the selector lever in the "P" range.
3. Measure the voltage between terminal C94-16 and
terminal C94-1 on the TCM pigtail connector by
J39200 DMM.
Is the voltage specified value? 816V Go to Step 4 Go to Step 10
Page 3745 of 4264
TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-65
Action Taken When The DTC Sets
The TCM operates shifting as following patterns.
Normal Fail S1 S2
1 3 - on
2 3 - on
3 3 - on
4 4 - off
No squat control.
No engine torque control.
No line pressure control.
No lock-up control.
No slope control.
No torque reduction.
Check Trans ON.
DTC stored.
No detect DTC P0722.
No detect DTC P0717.
Conditions For Clearing The DTC
The DTC can be cleared from the TCM history by
using a scan tool.
The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.
After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids
Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring .
Inspect for a broken wire inside the insulation.
When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.
DTC P0758 (FLASHING CODE 32) Shift Solenoid S2 Electrical
Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2
1. Install the scan tool.
2. Key “ON".
3. Review and record scan tool data.
4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P0758? — Go to Step 3 Refer to
Diagnostic Aids
3
1. Key “ON", engine run.
2. Place the selector lever in the "P" range.
3. Measure the voltage between terminal C94-15 and
terminal C94-1 on the TCM pigtail connector by
J39200 DMM.
Is the voltage specified value? 816V Go to Step 4 Go to Step 10
Page 3747 of 4264
TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-67
DTC P1767 (FLASHING CODE 67) ECM CAN Invalid
RTW37AMF000401
Circuit Description
The automatic transmission control system in AW30-
40LE uses high speed CAN bus system. The individual
CAN bus systems are connected via two interfaces and
can exchange information and data. This allows control
modules that are connected to different CAN bus
systems to communicate. Transmission control
modules in the vehicle that require continuous, rapid
communication are connected to the high speed CAN
bus. The automatic transmission is continuously notified
of the current engine load status. Since the automatic
transmission control module has to react immediately to
load status changes, rapid communication is required
between the engine control module and the automatic
transmission control module. The high speed CAN bus
in the AW30-40LE is designed as a two-wire CAN bus
(twisted pair). The wires are shielded and twisted. The
transmission rate is 500K band.
Condition for setting the DTC
The TCM detects invalid signal for 0.18 sec. (After the
TCM leaves a communication start with the ECM fo
r
0.64 sec)
The TCM detects above condition for 2.0 sec
continuously.
Action Taken When The DTC Sets
The line pressure is max.
The TCM judges APS(Accelerator Position Sensor)
angle is 0% at the time of shift operation.
No line pressure control.
No engine torque control.
No lock-up control.
No slope control.
Check Trans ON.
DTC stored.
No squat control.
Page 3754 of 4264
7A2-74 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)
DTC U2104 (FLASHING CODE 65) CAN BUSS OFF
RTW37AMF000401
Circuit Description
The automatic transmission control system in AW30-
40LE uses high speed CAN bus system. The individual
CAN bus systems are connected via two interfaces and
can exchange information and data. This allows control
modules that are connected to different CAN bus
systems to communicate. Transmission control
modules in the vehicle that require continuous, rapid
communication are connected to the high speed CAN
bus. The automatic transmission is continuously notified
of the current engine load status. Since the automatic
transmission control module has to react immediately to
load status changes, rapid communication is required
between the engine control module and the automatic
transmission control module. The high speed CAN bus
in the AW30-40LE is designed as a two-wire CAN bus
(twisted pair). The wires are shielded and twisted. The
transmission rate is 500K band.
Condition for setting the DTC
The TCM detects CAN BUS OFF for 0.18 sec (After the
TCM leaves a communucation start with the ECM fo
r
0.64 sec) continously..
Action Taken When The DTC Sets
The throttle pressure is max.
The TCM judges APS(Accelerator Position Sensor)
angle is 0% at the time of shift operation.
No throttle pressure reduction.
No torque reduction.
No lock-up control.
No slope control.
No squat control.
Check Trans ON.
DTC stored.
Engine REV is 7000 rpm.
Coolant tempreature is 80
C.