oil ISUZU TF SERIES 2004 Workshop Manual

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-37

Valve Body Assembly and Pressure Control Solenoid





244RY00009
Removal
Preparation:


Disconnect negative ( –) battery cable.
 Drain the fluid.
Refer to ATF REPLACEMENT in this section.
1. Remove the nineteen bolts and oil pan.

7A3-38 ON-VEHICLE SERVICE (AW30 –40LE)

2. Remove the oil strainer assembly.




244RY 00003
3. Disconnect the solenoid wiring connectors from the
solenoids.
4. Remove the twenty bolts from the valve body.
5. Remove the valve body assembly and pressure control solenoid.

After removing valve body assembly from the
transmission case, loosen the solenoid clamp
bolt and remove the pressure control solenoid
from the upper valve body assembly.
Also disconnect the harness connector from the
pressure control solenoid.

NOTE:

Two or more persons are required for removal and
installation of the valve body assembly and pressure
control solenoid.
 The check valve assembly (1) and the C0
accumulator piston springs (2) will fall from the
transmission case during removal of valve bod
y
assembly.
Protect these parts from damage. The B0 (3), C2 (4),
and B2 (5) accumulator piston and springs may also
fall free and must be protected.



244RY00018







244RY00006

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-39

Installation
To install, follow the removal steps in reverse order
noting the following point;
1. Reinstall the parts removed with the valve bod
y
assembly to their assigned positions in the
transmission case (check valve assembly, C0
accumulator pistons, etc). Install the valve bod
y
assembly to the transmission case.
Refer to REASSEMBLY OF MAJO
R
COMPONENTS (2).
2. Solenoid clamp bolt
Torque : 7 N 


m (61 Ib in)
3. Valve body fixing bolts
Each bolt location and length (mm) is indicated in
the figure.
Torque : 10 N 


m (87 Ib in)
NOTE: Tighten the bolts toward outside equally.




244R200078
4. Oil strainer fixing bolts
Torque : 10 N 


m (87 Ib in)
5. Oil pan fixing bolts
Torque : 8 N 


m (69 Ib in)

7A3-40 ON-VEHICLE SERVICE (AW30 –40LE)

Rear Oil Seal (Adapter Housing, 4
 
4)

Removal

1. Remove the front and rear propeller shaft assembly
from the transfer case.
2. Remove the transfer case assembly from the transmission case.
Refer to Section 4 DRIVELINE/AXLE.
3. Using a screwdriver, remove the rear oil seal.
Installation
1. Apply ATF to a new rear oil seal lip.
2. Using oil seal installer, install the rear oil seal to the adapter housing.
Oil seal installer : J –36797



RUW37ASH002401
3. Install the transfer case assembly.
Refer to section 4 DRIVE/AXLE.
4. Install the front and rear propeller shaft assembly.
Torque (Propeller shaft flange bolt) : 63 N 


m (46
Ib ft)

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-41

Rear Oil Seal (Extension Housing, 4
 
2)

Removal

1. Remove the rear propeller shaft assembly.
2. Using a screwdriver, remove the rear oil seal.
Installation
1. Apply ATF to a new rear oil seal lip.
2. Using oil seal installer, install the rear oil seal to the extension housing.
Oil seal installer : J –46197




249L100005
3. Install the rear propeller shaft.
Torque (Flange bolt) : 63 N 


m (46 Ib ft)

7A3-42 ON-VEHICLE SERVICE (AW30 –40LE)

Transmission Assembly
Transmission and Associated Parts




Legend
(9) Under Cover
(1) Rear Propeller Shaft (10) Flex Plate Torque Converter bolt
(2) Front Propeller Shaft (4WD only) (11) Shift Cable
(3) Middle Exhaust Pipe (12) Rear Mount Rubber
(4) Transfer Case Assembly (4WD only) (13) Heat Protector
(5) Fuel Pipe Clip and Bracket (14) Transmission Crossmember
(6) ATF Pipe and Clip (15) Transmission Assembly (2WD)
(7) Oil Level Gauge and Guide Tube (16) Transmission Assembly (4WD)
(8) Suspension Crossmember

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-43

Removal
NOTE: Before removing transmission and transfer
assembly from vehicle, change the transfer mode to
2WD using the 4WD push button switch on dash panel.
1. Disconnect battery ground cable.
2. Raise and support vehicle with suitable stands.
3. Remove front propeller shaft.(4WD only)
NOTE: Apply alignment marks on the flange at both
front and rear sides.
4. Remove rear propeller shaft.
NOTE: Apply alignment marks on the flange at the
differential side.


401RS023
5. Remove the middle exhaust pipe.



RTW37ASH0001

6. Disconnect the transfer harness connectors and the
clips.(4WD only)

Speed sensor
 2W-4W shift actuator
NOTE: Avoid turning the vehicle ignition switch to the
ON position when the 2WD-4WD connector is removed
(battery connected).
If the ignition switch must be turned to the ON position,
the controller must first be removed (memory must be
cleared because the CHECK 4WD INDICATOR will
light).
7. Support transfer case with a transmission jack.(4WD only)
8. Remove the transfer case assembly from the
transmission.(4WD only)
9. Disconnect the shift cable.
10. Remove the fuel pipe clips with the fuel pipes from the brackets and put aside it. Remove the fuel pipe
brakets from the transmission.






P1010010
11. Discinnect the transmission harness connectors
and clips.
12. Remove the oil level gauge and the guide tube.
13. Remove the suspension crossmember.

7A3-48 ON-VEHICLE SERVICE (AW30 –40LE)

11. Install the suspension crossmember.
Torque: 65 N 


m (6.6 kg 


m/48 lb ft)
12. Install filler tube and insert oil level gage.
Torque: 22 N 


m (2.2 kg 


m/16 lb ft)
13. Install select cable by connecting inner cable to
select lever and installing outer cable with bracket.
14. Install the fuel pipe brackets to the transmission. Install the fuel pipe clips with the pipes to the
bracket.





P1010010
15. Connect the transmission harness connectors and
clips.
16. Connect transmission oil cooler pipes to A/T.
Torque: 44 N 


m (4.5 kg



m/33 lb ft)
17. Install oil cooler pipe clamp and bracket to the
converter housing.


18.Tighten oil cooler pipe clamp bolt at the engine
mount side.




P1010024
19. Install the transfer case assembly.(4WD only)

Apply a thin coat of molybdenum disulfide grease
to the input shaft spline as shown in the figure.


260R300001

Install the transfer case assembly.

UNIT REPAIR (AW30–40LE) 7A4–1
TRANSMISSION
CONTENTS
UNIT REPAIR (AW30–40LE)
Major Components (1) ................................... 7A4–3
Major Components (1) and Associated
parts ........................................................... 7A4–3
Disassembly steps...................................... 7A4–3
Components (1) ............................................. 7A4–5
Reassembly ................................................ 7A4–5
Major Components (2) ................................... 7A4–7
Major Componets (2) and Associated
Parts ........................................................... 7A4–7
Disassembly ............................................... 7A4–8
Reassembly ................................................ 7A4–11
Major Components (3) ................................... 7A4–16
Major Components (3) and Associated
Parts ........................................................... 7A4–16
Disassembly ............................................... 7A4–17
Reassembly ................................................ 7A4–25
Diaassembly, Inspection and Reassembly
of minor Components ................................. 7A4–37
Oil Pump ........................................................ 7A4–38
Disassembly View ...................................... 7A4–38
Disassembly ............................................... 7A4–38
Inspection and Repair................................. 7A4–39
Reassembly ................................................ 7A4–41
OD Planetary Gear and OD Direct Clutch
Assembly (C–0).......................................... 7A4–43
Disassembled View .................................... 7A4–43
Disassembly ............................................... 7A4–44
Inspection and Repair................................. 7A4–47
Reassembly ................................................ 7A4–48
OD Support Assembly ................................... 7A4–53
Disassembled View .................................... 7A4–53
Disassembly ............................................... 7A4–53
Inspection and Repair................................. 7A4–54
Reassembly ................................................ 7A4–55
Direct Clutch Assembly (C-2) ........................ 7A4–58
Disassembled View .................................... 7A4–58
Disassembly ............................................... 7A4–59
Inspection and Repair................................. 7A4–60
Reassembly ................................................ 7A4–61
Forward Clutch Asseembly (C-1)................... 7A4–64
Disassembled View .................................... 7A4–64
Disassembly ............................................... 7A4–65
Inspection and Repair................................. 7A4–66
Reassembly ................................................ 7A4–67
Front Planetary Gear ..................................... 7A4–71
Disassembled View .................................... 7A4–71
Disassembly ............................................... 7A4–71
Inspection and Repair................................. 7A4–71
Reassembly ................................................ 7A4–72Planetary Sun Gear and No.1 One-Way
Clutch ......................................................... 7A4–73
Disassembled View .................................... 7A4–73
Disassembly ............................................... 7A4–74
Inspection and Repair ................................. 7A4–74
Reassembly ................................................ 7A4–75
Second Brake Assembly (B–2)...................... 7A4–77
Disassembled View .................................... 7A4–77
Disassembly ............................................... 7A4–77
Inspection and Repair ................................. 7A4–78
Reassembly ................................................ 7A4–78
Rear Planetary Gear Assembly and Output
Shaft ........................................................... 7A4–81
Disassembled View .................................... 7A4–81
Disassembly ............................................... 7A4–82
Reassembly ................................................ 7A4–84
First and Reverse Brake (B–3) ...................... 7A4–87
Disassembled View .................................... 7A4–87
Disassembly ............................................... 7A4–88
Reassembly ................................................ 7A4–89
Transmission Valve Body assembly .............. 7A4–92
Disassembled View .................................... 7A4–92
Disassembly ............................................... 7A4–93
Reassembly ................................................ 7A4–93
Lower Valve Body .......................................... 7A4–96
Cross Section ............................................. 7A4–96
Disassembly ............................................... 7A4–98
Inspection and Repair ................................. 7A4–103
Reassembly ................................................ 7A4–104
Upper Valve Body .......................................... 7A4–109
Cross Section ............................................. 7A4–109
Disassembly ............................................... 7A4–111
Inspection and Repair ................................. 7A4–115
Reassembly ................................................ 7A4–116
Transmission Case ........................................ 7A4–121
Disassembled View .................................... 7A4–121
Disassembly ............................................... 7A4–121
Reassembly ................................................ 7A4–122
Torque Converter........................................... 7A4–124
Inspection and Repair ................................. 7A4–124
Adapter Housing (4
4)................................. 7A4–125
Disassembled View .................................... 7A4–125
Disassembly ............................................... 7A4–125
Reassembly ................................................ 7A4–125
Ex tension Housing (4
2) ............................. 7A4–126
Disassembled View .................................... 7A4–126
Disassembly ............................................... 7A4–126
Reassembly ................................................ 7A4–126
Main Data and Specifications ........................ 7A4–128

UNIT REPAIR (AW30–40LE) 7A4–3
Major Components (1)
Major Components (1) and Associated parts
RTW 37A M F00 0601
E nd O FCallo ut
Disassembly steps
1. Remove the torque converter.
2. Remov e the select lev er.
Legend
(1) Torque converter
(2) Select lever
(3) Neutral start switch (Mode switch)
(4) Elbow
(5) Oil temperature sensor
(6) Breather hose
(7) Input revolution sensor(8) Output revolution sensor (4
4)
(9) Output revolution sensor (4
2)
(10) Speedometer sensor, speedometer driven gear
and plate (4
2)
(11) Extension housing (4
2)
(12) Adapter housing (4
4)
(13) Transmission assembly