suspension ISUZU TF SERIES 2004 Workshop Manual

PROPELLER SHAFT 4A-3
MAIN DATA AND SPECIFICATIONS
REAR PROPELLER SHAFT

mm(in)
4

2 Model
Engine Model 4JA1-T(L) 4JA1-TC 4JH1-TC
Transmission Type 5 M/T (MUA) 5M/T (MUA) 4A/T
Wheel Base Long Long Extra Long Long
Front Suspension
High Ride
SuspensionExcept High
Ride
Suspension


Rear Axle 
220mm 



Type 
OBS 



Outside Diameter mm 75 68.9 68.9 68.9 63.5
(in) (2.95) (2.71) (2.71) (2.71) (2.50)
Inside Diameter mm 71.8 64.9 64.9 64.9 60.3
(in) (2.89) (2.63) (2.63) (2.63) (2.44)
Length 1st(L1) mm 799.5 798.5 801.5 946.5 720.5
(in) (31.48) (31.44) (31.56) (37.26) (28.37)
2nd(L2) mm 796 801 796 801 801
(in) (31.34) (31.54) (31.34) (31.54) (31.54)
Spline Major mm 29.89 29.89 29.89 29.89 29.89
Diameter (in) (1.18) (1.18) (1.18) (1.18) (1.18)
Fix Bolt Size M10 M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement To T/M)



mm(in)
4

2 Model
Engine Model C24SE
6VE1
Transmission Type 5M/T (MUA)
5M/T (MUA) 4A/T
Wheel Base Long Extra Long Long Extra Long Long Extra Long
Front Suspension High Ride
Suspension Except High
Ride
Suspension










Rear Axle 


220mm 



Type 


OBS 



Outside Diameter mm 75 75 75 68.9 68.9 75 75
(in) (2.95) (2.95) (2.95) (2.71) (2.71) (2.95) (2.95)
Inside Diameter mm 71.8 71.8 71.8 64.9 64.9 71.8 71.8
(in) (2.89) (2.89) (2.89) (2.63) (2.63) (2.89) (2.89)
Length 1st(L1) mm 823.5 820.5 970.5 823.5 971.5 778.5 928.5
(in) (32.42) (32.30) (38.21) (32.42) (38.25) (30.65) (36.56)
2nd(L2) mm 801 796 796 801 801 801 801
(in) (31.54) (31.34) (31.34) (31.54) (31.54) (31.54) (31.54)
Spline Major mm 29.89 29.89 29.89 29.89 29.89 30.48 30.48
Diameter (in) (1.18) (1.18) (1.18) (1.18) (1.18) (1.20) (1.20)
Fix Bolt Size M10 M10 M10 M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement To T/M)

4A-4 PROPELLER SHAFT

mm(in)
4

4 Model
Engine Model 4JA1-T(L) 4JA1-TC 4JH1-TC
Transmission Type 5M/T (MUA) 5M/T (MUA) 4A/T
Wheel Base Long Long Extra Long Long
Front Suspension








Rear Axle 220mm 220mm 


Type OBS OBS 


Outside Diameter mm 75 68.9 68.9 63.5
(in) (2.95) (2.71) (2.71) (2.50)
Inside Diameter mm 71.8 64.9 64.9 60.3
(in) (2.89) (2.63) (2.63) (2.44)
Length 1st(L1) mm 469.5 468.5 616.5 402.5
(in) (18.48) (18.44) (24.27) (15.85)
2nd(L2) mm 801 801 801 801
(in) (31.54) (31.54) (31.54) (31.65)
Spline Major mm 29.89 29.89 29.89 29.89
Diameter (in) (1.18) (1.18) (1.18) (1.18)
Fix Bolt Size M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement To T/M)


mm(in)
4

4 Model
Engine Model C24SE 6VE1
Transmission Type 5M/T
(MUA) 5M/T (MUA) 4A/T
Wheel Base Long Long Extra Long Long
Front Suspension




Rear Axle    
Type    
Outside Diameter mm 63.5 68.9 68.9 75
(in) (2.50) (2.71) (2.71) (2.95)
Inside Diameter mm 60.3 64.9 64.9 71.8
(in) (2.44) (2.63) (2.63) (2.89)
Length 1st(L1) mm 495.5 492.5 641.5 484.5
(in) (19.51) (19.39) (25.26) (19.07)
2nd(L2) mm 801 801 801 801
(in) (31.54) (31.54) (31.54) (31.54)
Spline Major mm 29.89 29.89 29.89 29.89
Diameter (in) (1.18) (1.18) (1.18) (1.18)
Fix Bolt Size M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement To T/M)

4A-8 PROPELLER SHAFT
Rear Propeller Shaft
General Description
4




2 (Except High Ride Suspension) Model
F04R300001

4





2 (High Ride Suspension), 4





4 Model
401R300007

Torque is transmitted from the transmission to the
axle through propeller shaft and universal joint
assembles. All propeller shafts are the balanced
tubular type. A splined slip joint is provided in some
drivelines.

Since the propeller shaft is total balanced carefully,
welding or any other modification are not permitted. 
Alignment marks should be applied to each
propeller shaft before removal.

Be sure vehicle is stopped, engine is not running,
brake is secured and vehicle is secured to prevent
injury.

Be careful not to grip the propeller shaft tube too
tightly in the bise as this will be cause deformation.

4C1-2 FRONT WHEEL DRIVE
PAGE
Front Hub and Disc (4





2 Except High Ride Suspension Model) ................................. 4C1- 42
Disassembly ................................................................................................................ 4C1- 42
Inspection and Repair................................................................................................. 4C1- 45
Reassembly ................................................................................................................. 4C1- 46
Front Hub and Disc (4




4, 4




2 High Ride Suspension, 4




4 Rigid Hub,
4




4 Shift On The Fly Model) ........................................................................................... 4C1- 50
Disassembly ................................................................................................................ 4C1- 50
Inspection and Repair................................................................................................. 4C1- 52
Reassembly ................................................................................................................. 4C1- 53
Front Hub and Disc (4





4 Manual Locking Hub Model) ................................................. 4C1- 57
Disassembly ................................................................................................................ 4C1- 57
Inspection and Repair................................................................................................. 4C1- 60
Reassembly ................................................................................................................. 4C1- 61
Troubleshooting .............................................................................................................. 4C1-67
Special Service Tool ................................................................................................... 4C1-75

FRONT WHEEL DRIVE 4C1-7
SERVICING


Hub Bearing Preload at the Wheel Pin
4
4, 4
2 (High Ride Suspension) Model N (lb)

New bearing and New oil seal 20 - 25 (4.4 - 5.5)
Reuse bearing and New oil seal 12 - 18 (2.6 - 4.0)
42 (Except High Ride Suspension) Model N (lb)

New bearing and New oil seal 8 - 12 (1.8 - 2.2)
Reuse bearing and New oil seal 8 - 12 (1.8 - 2.2)

FRONT WHEEL DRIVE 4C1-9
FRONT HUB AND DISC (4





2 Except High Ride Suspension Model)
412R300010

4C1-10 FRONT WHEEL DRIVE
(4





2 High Ride Suspension Model)
RTW34CLF000701

4C1-14 FRONT WHEEL DRIVE
FRONT DRIVE AXLE ASSEMBLY
Front Drive Axle Assembly and Associated Parts


RTW440LF000501

Legend
1. Propeller Shaft
2. Front Axle Case Assembly and Front Drive
Shaft Assembly
3. Washer

4. Mounting Bolt
5. Tie-rod End ; Steering Unit
6. Knuckle and Back Plate
7. Hub and Disc Assembly
8. Suspension Crossmember

FRONT WHEEL DRIVE 4C1-15

Removal
1. Jack up the vehicle and support it using jack stand.
2. Remove the tire and wheel.
3. Remove the stone guard.
4. Remove the brake caliper fixing bolt and hang the caliper.
Refer to Disc Brakes in Brake section.
5. Remove the antilock brake system speed sensor.
Refer to Front Wheel Speed Sensor in Brake section.
6. Remove the hub and disc assembly.
Refer to Front Hub and Disc in this section.
7. Remove the propeller shaft, refer to Front Propeller Shaft in
this section.
8. Loosen the height control arm of the torsion bar, then
remove the torsion bar from lower control arm.
Refer to Torsion Bar in Suspension section.
9. Remove the suspension crossmember.
10. Remove the lower nut (1) of the stabilizer link.
11. Remove the lower bolt and nut (2) of the shock absorber.

12. Remove the tie-rod end from the knuckle.
Refer to Power Steering Unit in Steering Section.
13. Disconnect the breather hose of the front axle.
14. Disconnect the actuator connector. (With shift on the fly)
15. Remove the bolts and nuts of the lower control arm (Frame
side), then disconnect the lower control arm from frame.
16. Disconnect between the right side upper control arm and
the knuckle, then remove the knuckle with lower control
arm.
CAUTION :
When removing the knuckle, be careful not to damage the
oil seal inside of the knuckle.

4C1-16 FRONT WHEEL DRIVE
17. Support the differential case by the jack.
18. Remove the front axle mounting bolts and nuts, lower the
jack slowly. Remove the left side drive shaft end from the
knuckle, then lower the axle assembly from the vehicle.
CAUTION :
1. During the work, be sure that the axle assembly is
supported securly.
2. Be careful not to damage the bellows of the power
steering unit by interference.
3. Be careful not to damage the breater pipe and breater
pip bracket of the shift on the fly by interference.


Installation
1. Support the differential case by the jack.
2. Jack up the front drive axle assembly, install the left side
drive shaft to the knuckle, then install the mount bolts and
nuts.
CAUTION :
1. Be careful not to damage the bellows of the power
steering unit by interference.
2. Be careful not to damage the breater pipe and breater
pip bracket of the shift on the fly by interference.
3. When installing the drive shaft to the knuckle, be
careful not to damage the oil seal inside of the knuckle.

RTW34CSH000101
3. Tighten the mounting bolts and nuts to the specified torque.
Torque : 169 N·m (17.2kg·m/124 lb ft)



4. Install the right side knuckle with lower control arm to the
upper control arm.
Refer to Knuckle in Suspension section.
CAUTION :
When insert the drive shaft to the knuckle, be careful not
to damage the oil seal inside of the knuckle.

5. Align the bolt hole of the lower control arm, install the bolts
and nuts.