Rear Wheel Speed Sensor JAGUAR X308 1998 2.G Workshop Manual

            206‐07:  Powe r Brake  Actuation  
                 Specif
ication
 
                 Description  and  Operation  
                     Brake Booster  
                 Removal and  Installation  
                     Brake Booster  (70.50.17)  
                     Brake Booster  and  Brake  Master  Cylinder  (70.50.18)  
 
             206‐09:  Anti ‐Lock  Control  
                 Specification  
                 Description  and  Operation  
                     Anti‐Lock  Control  
                 Diagnosis  and  Testing  
                     Anti‐Lock  Control  
                 Removal and  Installation  
                     Anti‐Lock  Brake  System  (ABS)  Module  (70.60.02)  
                     Front Wheel  Speed  Sensor  (70.60.03)  
                     Hydraulic Cont
rol Unit  (HCU) 
                     Rear Wheel  Speed  Sensor  (70.60.04)  
                     Wheel Speed  Sensor  Ring  (70.60.25)  
 
        211:  Steering  System  
 
             211‐00:  Steering  System ‐ General  Information  
                 Specification  
                 Description  and  Operation  
                     Steering System  
                 Diagnosis  and  Testing  
                     Steering Sy
stem  
                 General Procedures  
                     Power Steering  System Filling  and  Bleeding  
                     Power Steering  System Flushing  (57.15.08)  
                     Power Steering  System Vacuum  Filling  and  Bleeding  
                     Steering Gear  Centralizing  
 
  

Front Suspension -
Lubri
cants, Fluids, Sealants and Adhesives
Press-In Loads
Torques


UnitS
pecification
Loctite27

0
Greas

e
Shell Retin
ax 'A'
Greas

e
Castro
l 'NTR'
Com

ponent
Kn
Ball join

t to upper wishbone
25
- 50
B

all joint to lower wishbone
25
- 50
Com

ponent
Nm
N

ut - ball joint, upper wishbone to vertical link.
60
-80
N

ut - ball joint, lower wishbone to vertical link.
60
-80
Nu

t - fulcrum bolt, upper wishbone.
60
-80
N

ut - ball joint, tie rod to steering arm.
71
-85
Bol

t - wheel speed sensor to vertical link.
8-1
0
Bol

t - front mounting to crossbeam.
22
-28
Bolt

- mounting , stabilizer bar.
30
-40
N

ut - link arm ball joint to stabilizer bar.
60
-80
Bolt

- mounting, steering rack to crossbeam.
41
-54
B

olt - front mounting, crossbeam to body.
22
-28
Bol

t - spring pan to lower wishbone.
70
-90
N

ut - shock absorber to upper mounting
(vehicles with adaptive damping).
16
-18
Nu

t - shock absorber to upper mounting (vehicles without adaptive damping).
30
-40
N

ut - shock absorber lower to wishbone.
43
-57
B

olt - engine Hydramount to crossbeam.
34
-46
B

olt - crossbeam rear mounting to body.
13
1-185
Bol

t - generator cooling du
ct deflector to crossbeam.
17
-23
N

ut - lower steering column to pinion shaft.
22
-28
N

ut - hub, speed sensor rotor.
27
0-330
B

olt - shield, brake disc.
9-1
2
Bol

t - lower wishbone, front arm to rear arm.
77
-103
Nu

t - stabilizer bar link arm to wishbone bracket.
41
-54
N

ut - wishbone front
eccentric bolt.
11
3-153
Nu

t - wishbone rear
eccentric bolt.
11
3-153
N

ut - fulcrum shaft, upper wishbone.
60
-80
Bolt -

power steering pi
pes to pinion housing.
9-1
2

Inst
all sensor bolt an
d tighten to 8-10Nm.

22
.
Connect wheel speed sensor harness.
1. Connect wheel speed sensor harness to sensor.
2. Using new tiestraps secure wheel speed sensor harness to upper wishbone.

23
.
Install brake calipers.
R
emove tie supporting brake caliper.
1. Install caliper on carrier.
2. Install guide pins.
3. Install guide pin dust caps.
4. Install caliper spring clip.
24. Install road wheel. Re fer to Section 100-02.
25. Raise vehicle, remove stands and lower vehicle onto road
wheels.

26
.
Ensuring graduation mark remains aligned, finally tighten
wishbone rear eccentric bolt to 113-153Nm.
27. Check wheel alignment and if necessary adjust. Refer to
57.65.01.

2.
Using new tiestraps secure wheel speed sensor
harness to upper wishbone.

25
.
Install brake calipers.
R
emove tie supporting brake caliper.
1. Install caliper on carrier.
2. Install guide pins and tighten to 25-30Nm.
3. Install guide pin dust caps.
4. Install caliper spring clip.

26
.
Position and partially tighten wishbone rear eccentric bolt.
R
otate eccentric bolt to align large graduation with mark
made during removal.

27
.
Position and partially tighten wishbone front eccentric bolt.
R
otate eccentric bolt to align large graduation with mark
made during removal.
P
artially tighten bolt.
28. Fit road wheel. Refer to Section 100-02.
29. Raise vehicle, remove stands and lower vehicle onto road
wheels.
30. Ensuring graduation mark remains aligned, finally tighten
wishbone rear eccentric bolt to 113-153Nm.

Rear
Suspension - Rear Susp
ension and Axle Assembly
Re
moval and Installation
Remov

al
1.
CAUTI
ON: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used.
For additional informat ion, refer to Section 100
-0
0 General
Informati

on
.
R
aise the rear of the vehicle
and support on axle stands.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.
2.
R
emove the rear wheels.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire

s
.

3. CAUTI
ON: Do not suspend the caliper from the brake
hose as this will damage the hose.
• NOTE: Right-hand shown, left-hand similar
Remove the brake calipers from the carriers.
1. Remove the caliper spring clip.
2. Remove the guide pin dust caps.
3. Slacken and withdr aw the guide pins.
4. Remove the caliper from the carrier and secure to the suspension mounting bracket using a tie strap.

4. NOTE
: Right-hand shown, left-hand similar
Disconnect the wheel speed sensor electrical connectors.
5. NOTE: Right-hand shown, left-hand similar
Remove and discard th e tie straps securing the wheel speed
sensor harnesses to the brake hose clips.

18
.
Install the brake caliper on to the carrier.
1. Position the caliper asse mbly on to the carrier.
2. Install the guide pins and tighten to 25-30 Nm.
3. Install the dust caps.
4. Install the brake caliper spring clip.

19
.
Connect the wheel speed sensor electrical connector.

20
.
Using a new tie strap, secure the wheel speed sensor harness
to the brake hose clip.
21. Install the rear wheels.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire

s
.
22
.
Remove the axle stands and lower the vehicle.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.
23
.
Check and adjust the rear whee l alignment as necessary.
For additional informat ion, refer to Section 204
-00
Suspension


Sy

stem
- General
Information
.

Rear Su
spension - Rear Shock Absorber
Re
mo
val and Installation
Remov
a
l
S
p
ecial Tool(s)

Spri
ng C
ompressors
204-179 (JD 199)

Spri ng Re
taining straps
204-179-1 (JD 199-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used.
For additional informat ion, refer to Section 100
-00
General
Informati
o
n
.
R a
ise the rear of the vehicle
and support on axle stands.
For additional informat ion, refer to Section 100
-02
Jacking and
Liftin
g.
2. Re
move the relevant rear wheel.
For additional informat ion, refer to Section 204
-04 W
heels and
Tire
s.

3. CAUTIO
N: Do not suspend the caliper from the brake
hose as this will damage the hose.
Remove the brake caliper from the carrier.
1. Remove the caliper spring clip.
2. Remove the guide pin dust caps.
3. Slacken and withdr aw the guide pins.
4. Remove the caliper from the carrier and secure to the suspension mounting bracket using a tie strap.
4. Disc
onnect the wheel speed sensor electrical connector.

22. R
elease the tie strap securing the brake caliper to the
suspension mounting bracket.

23 . Install
the brake caliper on to the carrier.
1. Position the caliper asse mbly on to the carrier.
2. Install the guide pins and tighten to 25-30 Nm.
3. Install the dust caps.
4. Install the brake caliper spring clip.

24 . Conne
ct the wheel speed sensor electrical connector.

25 . U
sing a new tie strap, secure the wheel speed sensor harness
to the brake hose clip.
26. Install the rear wheel.
For additional informat ion, refer to Section 204
-04 W
heels and
Tire
s.
27 .
Remove the
axle stands
and lower the vehicle.
For additional informat ion, refer to Section 100
-02
Jacking and
Liftin
g.

Rear
Suspension - Spring
Re
moval and Installation
Remov

al
S
pecial Tool(s)

Spri

ng Compressors
204-179 (JD 199)

Spri
ng Retaining straps
204-179-1 (JD 199-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used.
For additional informat ion, refer to Section 100
-0
0 General
Informati

on
.
R
aise the rear of the vehicle
and support on axle stands.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.
2.
R
emove the relevant rear wheel.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire

s
.

3. CAUTI
ON: Do not suspend the caliper from the brake
hose as this will damage the hose.
Remove the brake caliper from the carrier.
1. Remove the caliper spring clip.
2. Remove the guide pin dust caps.
3. Slacken and withdr aw the guide pins.
4. Remove the caliper from the carrier and secure to the suspension mounting bracket using a tie strap.
4. Di
sconnect the wheel speed sensor electrical connector.

9. P
osition special tool 204-195 on hub studs and install securing
nuts.

10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts and withdraw special tool (204-195)
from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.

14
.
Remove wheel speed sensor.
Disc
onnect wheel speed sensor harness from sensor
R

emove wheel speed sensor se
curing bolt and withdraw
sensor from hub carrier.

15
.
Sever and discard wheel speed sensor harness tie strap and
position harness for access.
16. Remove hub nut and collar.
Re
move nut.