auxiliary battery JAGUAR X308 1998 2.G Workshop Manual

                    Side Turn  Signal  Lamp  (86.41.41)  
                     Side Turn  Signal  Lamp  Bulb  (86. 41.42)  
 
             417‐02
:
 Interior  Lighting  
                 Specification  
                 Description  and  Operation  
                     Interior Lighting  
                 Diagnosis  and  Testing  
                     Interior Lighting  
                 Removal and  Installation  
                     Door Courtesy  Lamp (86.40.38)  
                     Door Courtesy  Lamp Bulb  (86.40.47)  
                     Door Courtesy  Lamp Lens  (86.40.35)  
                     Glove Co
mpartment  Lamp  (86.45.08)  
                     Luggage Compartment  Lamp (86.45.16)  
                     Vanity Mirror  Lamp  (76.10.50)  
 
             417‐04:  Daytime  Running  Lamps  (DRL) 
                 Description  and  Operation  
                     Daytime Running Lamps  (DRL) 
                 Diagnosis  and  Testing  
                     Daytime Running Lamps  (DRL) 
 
        418:  Electrical  Distribution  
 
             418‐00:  Module  Communications  Network  
                 Description  and  Operation  
                     Communications  Ne
twork 
                                                      Removal
 and  Installation  
                     Battery
 Junction  Box  (BJB)  (86.70.69)  
                     Central
 Junction  Box (CJB)  (86.70.72)  
                     Front
 Auxiliary  Junction  Box  (86.70.73)  
                     Rear
 Auxiliary  Junction  Box  (86.70.74)  
 
  
418 ‐02:  Wiring  Harnesses  
Description  and  Operati
on
 
Wiring  Harness  
General  Procedures  
Wiring  Harness  Repair 

Connector Pin Identity Chart for FC043

Control Panel Communication
The control panel provides operator interface with the climate control system.
Control panel operation is described in detail in the D section.
Control Panel Inputs (I/P) / Outputs (O/P)
Pin NumberCircuitCircuit Function
001Ignition positive supply
002Battery isolate supply
003Auxiliary ground
004Auxiliary ground to control panel
005Battery supply
006Engine speed input
007Electrical load drive inhibit
008+5V sensors
009Clutch request to ECM
010Diagnostic L-line
011Not used
012Ignition (positive) to control panel
013System ground
014Ground to control panel
015Air conditioning isolation relay
016Vehicle speed
017Pressure switch
018Aspirator motor (In-car sensor)
019Sensor ground
020Logic ground for diagnostic lines
021Diagnostic K-line
022Not used
Pin NumberCircuitCircuit Function
1Input CLOCK
2Input START
3Input DATA IN
4Output DATA OUT
5Input ignition (positive)
6Input auxiliary (negative)
7Ground
8Dimmer
9Dimmer override
10Not used
11Not used
12Not used

Module Communications Network - Front Auxiliary Junction Box
Removal and Installation
Removal

1. Disconnect battery ground cable; refer to 86.15.19.
2. Open bonnet and fit body pa intwork protection sheets.

3. Remove positive supply power cable.
1. Displace cover.
2. Remove nut.
3. Disconnect cable.

4. Remove fuse box fro m mounting panel.
1. Release securing latch, upwards, displace fuse box
outwards and remove from mounting panel.
2. Release securing tangs and remove cover.

5. Remove fuse box.
1. Identify and disconne ct harness connectors.
6. Remove fuses and relays.

Module Communications Network - Rear Auxiliary Junction Box
Removal and Installation
Removal

1. Disconnect battery ground cable; refer to 86.15.19.
2. Open bonnet and fit body pa intwork protection sheets.

3. Remove positive supply power cable.
1. Displace cover.
2. Remove nut.
3. Disconnect cable.

4. Remove fuse box fro m mounting panel.
1. Remove nuts.
Reposition fuse box for access to connectors.

5. Remove fuse box.
Identify and disconnect harness connectors.
6. Remove fuses and relay.