u3003 JAGUAR XFR 2010 1.G User Guide

DTC Description Possible Causes Action U0300-00
Internal Control
Module Software
Incompatibility - No
sub type information
Car configuration file
stored in parking aid
control module does not
match the master car
configuration file
Master car configuration
file not being
transmitted by master
control module
Using the manufacturer approved diagnostic system,
check all other control modules, for related DTCs and
refer to the relevant DTC index
Check the components installed on the vehicle were
installed by the factory or a dealer
Install the original component or a new one as
required U0422-00
Invalid Data Received
From Body Control
Module - No sub type
information
Invalid data received
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U0423-00
Invalid Data Received
From Instrument Panel
Control Module - No
sub type information
Invalid data received
Using the manufacturer approved diagnostic system,
check instrument cluster, for related DTCs and refer
to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U0443-00
Invalid Data Received
From Body Control
Module "B" - No sub
type information
Invalid data received
Using the manufacturer approved diagnostic system,
check auxiliary junction box, for related DTCs and
refer to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U2100-00
Initial Configuration
Not Complete - No sub
type information
Car configuration file not
the same as expected by
the parking aid control
module
NOTE: After updating the car configuration file, set the
ignition to on and wait 30 seconds before clearing the DTCs

Using the manufacturer approved diagnostic system,
check and update the car configuration file as
required. Clear the DTC and retest U2101-00
Control Module
Configuration
Incompatible - No sub
type information
Parking aid control
module configuration
error
Using the manufacturer approved diagnostic system
check and up-date the car configuration file as
required. Clear the DTC and re-test U3000-49
Control Module -
Internal electronic
failure
Parking aid control
module internal failure
Using the manufacturers approved diagnostic system
clear the DTC, cycle the ignition off, then on, and
check if the DTC is still logged
If the DTC is still logged suspect the parking aid
control module U3002-81
Vehicle Identification
Number - Invalid serial
data received
VIN Mismatch, stored
VIN does not match
broadcast VIN
Using the manufacturers approved diagnostic system
clear the DTC, cycle the ignition off, then on, and
check if the DTC is still logged
If the DTC is still logged replace the parking aid
control module U3003-16
Battery voltage -
Circuit voltage below
threshold
Circuit voltage below
threshold
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Check the vehicle charging system performance to
ensure the voltage regulation is correct
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge
and starting/charging system performance
Refer to the electrical circuit diagrams and check
parking aid control module power and ground circuits

DTC Description Possible Causes Action for short circuit to ground, short circuit to power,
open circuit
Clear the DTC and retest U3003-17
Battery Voltage -
Circuit voltage above
threshold
Circuit voltage above
threshold
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Check the vehicle charging system performance to
ensure the voltage regulation is correct
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge
and starting/charging system performance
Refer to the electrical circuit diagrams and check
parking aid control module power and ground circuits
for short circuit to ground, short circuit to power,
open circuit
Clear the DTC and retest U3003-62
Battery Voltage -
Signal compare failure
Signal compare failure in
battery voltage, of 2
volts or more, between
parking aid control
module and central
junction box
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Check the vehicle charging system performance to
ensure the voltage regulation is correct
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge
and starting/charging system performance
Refer to the electrical circuit diagrams and check
parking aid control module power and ground circuits
for short circuit to ground, short circuit to power,
open circuit
Clear the DTC and retest

DTC Description Possible Causes Action U0142-00
Lost Communication
With Body Control
Module "B" - No
subtype information
Missing message from
RJB
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Carry out CAN network integrity test using
the manufacturer approved diagnostic system. Refer
to the electrical circuit diagrams and check power
and ground supplies to RJB U0155-00
Lost Communication
With Instrument Panel
Cluster (IPC) Control
Module - No subtype
information
Missing message from
instrument cluster
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Carry out CAN network integrity test using
the manufacturer approved diagnostic system. Refer
to the electrical circuit diagrams and check power
and ground supplies to instrument cluster U0300-00
Internal Control
Module Software
Incompatibility - No
subtype information
Invalid configuration
message is received
Re-configure the RJB using the manufacturer
approved diagnostic system. Clear the DTC and
retest. If the DTC is still logged suspect the remote
keyless entry module, refer to the new module
installation note at the top of the DTC Index U201F-00
External Receiver - No
subtype information
No subtype information -
communication error
Suspect the RF receiver, check and install a new RF
receiver as required, refer to the new
module/component installation note at top of DTC
Index U201F-13
External Receiver -
Circuit open
Line open
Refer to the electrical circuit diagrams and test RF
receiver communication circuit to remote keyless
entry module for short to ground or open circuit U201F-87
External Receiver -
Missing message
Transmission error
Refer to the electrical circuit diagrams and check
the data line between the RF receiver and the
remote keyless entry module for short, open circuit.
Suspect the RF receiver or remote keyless entry
module, check and install a new RF receiver or
remote keyless entry module as required, refer to
the new module/component installation note at top
of DTC Index U2100-00
Initial Configuration
Not Complete - No
subtype information
No subtype information
Configure the Remote Keyless Entry module using
the manufacturer approved diagnostic system U2101-00
Control Module
Configuration
Incompatible - No subtype information
No subtype information
Re-configure the RJB using the manufacturer
approved diagnostic system U3000-49
Control Module -
Internal electronic
failure
Internal electronic failure
Install a new remote keyless entry module, refer to
the new module installation note at the top of the
DTC Index U3002-81
Vehicle Identification
Number - Invalid serial
data received
Vehicle/component
mis-match. Module
previously installed to
other vehicle
Install correct/new module to vehicle specification,
refer to the new module/component installation
note at the top of the DTC Index U3003-62
Battery Voltage -
Signal compare failure
Mis-match in battery
voltage, of 2 volts or
more, between remote
keyless entry module and
RJB
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system
Refer to the relevant section of the workshop
manual and test the battery and charging system

DTC Description Possible Causes Action B1A89-12
Satellite Antenna -
Circuit short to
battery
Satellite antenna circuit -
short to power
Refer to the electrical circuit diagrams and check
satellite antenna circuit for short circuit to power. Repair
wiring harness as required. Clear DTC and retest B1A89-13
Satellite Antenna -
Circuit open
Satellite antenna circuit -
open circuit, high
resistance
Refer to the electrical circuit diagrams and check
satellite antenna circuit for open circuit, high
resistance. Repair wiring harness as required. Clear DTC
and retest U3000-04
Control Module -
System internal
failures
System internal failure
Check and install a new satellite radio module as
required. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component U3000-4A Control Module -
Satellite radio module -
Using the manufacturer approved diagnostic system Incorrect component Incorrect component select the vehicle configuration main menu>vehicle installed installed configuration>display and modify the vehicle Car configuration configuration file data mismatch Check update as required U3000-55
Control Module -
Not configured
Satellite radio module -
Incorrect component
installed
Incorrect car configuration
file data received
Using the manufacturer approved diagnostic system
select the vehicle configuration main menu>select
configure existing modules menu and program the
satellite radio module U3000-87
Control Module -
Missing message
The satellite radio module
has not received the
configuration file
Master module not
transmitting configuration
file
Using the manufacturer approved diagnostic system
check that the satellite radio module is configured
correctly
Check that the configuration file is being transmitted by
the master module
Using the manufacturer approved diagnostic system,
complete a MOST network integrity test U3000-98
Control Module -
Component or
system over
temperature
Satellite radio module
cooling vents obstructed
Wiring harness fault
Internal electronic failure
Check for possible causes of the satellite radio module
overheating. Check that the ventilation is not
obstructed
Check for short circuit related DTCs. Refer to the
electrical circuit diagrams and check ground circuit for
high resistance. Check antenna circuit for short to power
or ground. Repair wiring harness as required. Clear DTC
and retest
Check for internal electronic failure related DTCs
If fault persists, check and install a new satellite radio
module. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component U3003-62
Battery Voltage -
Signal compare
failure
Signal compare failure
Satellite radio module
voltage differs more than
±2V compared to rear
junction box voltage
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge and
starting/charging system performance. Check power
supply circuit from rear junction box to satellite radio
module
Refer to electrical circuit diagrams and check the power
and ground supply circuits to the module. Repair wiring
harness as required. Clear DTC and retest

DTC Description Possible Causes Action Support for further advice. Under no circumstance
should any parts be replaced to overcome this issue U1A14-49
CAN Initialisation
Failure - Internal
electronic failure
Internal electronic failure
Suspect the speed control module. Check and install
a new module as required, refer to the new
module/component installation note at the top of
the DTC Index U2101-00
Control Module
Configuration
Incompatible - No sub
type information
Data sent from RJB is
invalid
Check/amend Car Configuration File using the
manufacturer approved diagnostic system, clear DTC
and re-test. If DTC remains, re-configure RJB using
manufacturer approved diagnostic system, clear DTC
and re-test. If DTC remains check RJB for DTCs and
refer to DTC Index U3000-41
Control Module -
General checksum
failure
Internal micro controller
error
Checksum fault
Suspect the speed control module. Check and install
a new module as required, refer to the new
module/component installation note at the top of
the DTC Index U3000-42
Control Module -
General memory failure
Internal RAM test fault
Suspect the speed control module. Check and install
a new module as required, refer to the new
module/component installation note at the top of
the DTC Index U3000-49
Control Module -
Internal electronic
failure
Internal control module
failure
Suspect the speed control module. Check and install
a new module as required, refer to the new
module/component installation note at the top of
the DTC Index U3000-63
Control Module -
Circuit/component
protection time-out
Circuit/component
protection time-out
The Control module internal protection has been
activated. Check for other related DTCs that could
lead to this event. Clear the DTC and retest. If the
problem persists, renew the module. Refer to the
warranty policy and procedures manual if a module is
suspect U3003-62
Battery Voltage -
Signal compare failure
Signal compare failure
Battery supply voltage
below a recognized value
Check vehicle battery and charging system. Refer to
the relevant section in the workshop manual. Refer
to the electrical circuit diagrams and check the power
and ground supply circuits to the modules www.JagDocs.com

DTC Description Possible Causes Action B1D55-13
Antenna#2 - Circuit
open
Antenna #2
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #2 circuit for open circuit B1D56-11
Antenna #3 Circuit -
Circuit short to
ground
Antenna #3
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for short to
ground B1D56-12
Antenna #3 Circuit -
Circuit short to
battery
Antenna #3
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for short to power B1D56-13
Antenna #3 Circuit -
Circuit open
Antenna #3
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for open circuit B1D57-11
Antenna #4 Circuit -
Circuit short to
ground
Antenna #4
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for short to
ground B1D57-12
Antenna #4 Circuit -
Circuit short to
battery
Antenna #4
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for short to power B1D57-13
Antenna #4 Circuit -
Circuit open
Antenna #4
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for open circuit B1D58-11 Television Output -
Circuit short to
ground
Television output
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for short to
ground B1D58-12 Television Output -
Circuit short to
battery
Television output
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for short to
power B1D58-13 Television Output -
Circuit open
Television output
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for open
circuit U3000-49
Control Module -
Internal electronic
failure
Internal
electronic failure
Suspect the television module, check and install a new module
as required, refer to the new module/component installation
note at the top of the DTC Index U3003-16
Battery Voltage -
Circuit voltage below
threshold
Circuit voltage
below threshold
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system U3003-17
Battery Voltage -
Circuit voltage above
threshold
Circuit voltage
above threshold
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system

DTC Description Possible Causes Action U3000-44
Control Module - Data
memory failure
EEPROM, External
RAM access failure
Suspect the TSD, check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3000-48
Control Module -
Supervision software
failure
Supervision software
failure
Re-configure the TSD using the manufacturer approved
diagnostic system U3000-4B
Control Module - Over
temperature
Touch panel backlight
- high temperature
detected
Allow the system to cool, clear the DTC and
check/monitor system for re-occurrence. If DTC re-occurs
suspect the TSD. Check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3000-55
Control Module - Not
configured
Incorrect Car
Configuration
Parameters received
Check/amend Car Configuration File using the
manufacturer approved diagnostic system U3000-87
Control Module -
Missing message
Car Configuration File
not received
Check RJB for related DTCs and refer to relevant DTC
Index. Check CAN and MOST networks, carry out the
CAN and MOST network tests using the manufacturer
approved diagnostic system U3000-98
Control Module -
Component or system
over temperature
TSD internal
temperature over
limit
Allow the system to cool, clear the DTC and
check/monitor system for re-occurrence. If DTC re-occurs
suspect the TSD. Check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3003-16
Battery Voltage -
Circuit voltage below
threshold
Circuit voltage below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system U3003-17
Battery Voltage -
Circuit voltage above
threshold
Circuit voltage above
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

DTC Description Possible Causes Action failure
U3000-45 Control
Portable audio
Suspect the portable audio interface module. Check and install a Module - Program interface module new module as required. Refer to the warranty policy and memory internal flash memory procedures manual if a module is suspect failure failure U3000-55
Control
Module - Not
configured
Portable audio
interface module not
configured correctly
Re-program the portable audio interface module, clear DTC and
re-test. If DTC remains carry out MOST tests and test USB cable
for open, short circuit, clear DTC and re-test. If DTC remains
suspect the portable audio interface module, check and install a
new module as required. Refer to the warranty policy and
procedures manual if a module is suspect U3003-62
Battery
Voltage -
Signal
compare
failure
Portable audio
interface module
voltage differs more
than ±2V compared
to central electronics
module voltage
Refer to the electrical circuit diagrams and check the fuses, power
and ground connections to both modules

DTC Description Possible Causes Action U3000-04
Control Module -
System internal
failures
Diversity antenna amplifier internal
failure
Renew the amplifier module U3000-4A
Control Module -
Incorrect
component
installed
Diversity antenna amplifier internal
incorrect component installed
- The module has been installed to
a vehicle not configured to accept
it
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-55
Control Module -
Not configured
Diversity antenna amplifier not
configured correctly
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-87
Control Module -
Missing message
Missing message
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-98
Control Module -
Component or
system over
temperature
Diversity antenna amplifier component or
system over temperature
Consider moving the amplifier mounting
position to prevent unit overheating. Cool
the vehicle interior down by ensuring it is
in the shade and have the A/C on cool.
When cool, clear the DTC and retest. If
the problem persists, renew the amplifier
module U3003-62
Battery Voltage -
Signal compare
failure
Mismatch in battery voltage of 2 volts or
more for longer than 1 minute, between
the measured battery voltage at the
Digital Audio Control Module C and the
battery voltage signal sent from the Rear
Junction Box.
Refer to the electrical guides and check
that power supply voltage at Digital Audio
Control Module C and Rear Junction Box is
not different by more than 2 volts. Rectify
as required

DTC Description Possible Causes Action module as required, refer to the new
module/component installation note at the top of the
DTC Index U3000-44
Control Module - Data
memory failure
Data memory failure
Re-configure the telephone module. If the DTC
remains, suspect the telephone module. Check and
install a new telephone module as required, refer to
the new module/component installation note at the
top of the DTC Index U3000-45
Control Module -
Program memory
failure
Program memory failure
Re-configure the telephone module. If the DTC
remains, suspect the telephone module. Check and
install a new telephone module as required, refer to
the new module/component installation note at the
top of the DTC Index U3000-55
Control Module - Not
configured
Incorrect car
configuration data
received
Re-configure the RJB using the manufacturer approved
diagnostic system. Clear DTC and re-test. If the DTC
remains suspect the telephone module. Check and
install a new module as required, refer to the new
module/component installation note at the top of the
DTC Index U3000-98
Control Module -
Component or system
over temperature
Component or system
over temperature
Check for additional DTCs and refer to DTC Index.
Clear DTC and re-test/monitor condition for
re-occurrence U3003-62
Battery Voltage -
Signal compare failure
Mis-match in battery
voltage, of 2 volts or
more, between
telephone module and
RJB
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system