tire pressure reset JEEP DJ 1953 Service Manual

D

HURRICANE
F4
ENGINE
D-112.
SERVICE
DIAGNOSIS

Poor
Fuel
Economy Ignition Timing Slow or Spark Advance Stuck

Carburetor
Float High
Accelerator Pump Not Properly Adjusted
High
Fuel
Pump Pressure

Fuel
Leakage
Leaky
Fuel
Pump Diaphragm
Loose Engine Mounting Causing High
Fuel
Level

in
Carburetor

Low
Compression Valves Sticking

Spark
Plugs Bad

Spark
Plug Cables Bad Weak
Coil
or Condenser Improper Valve Tappet Clearance

Carburetor
Air Cleaner Dirty
High Oil Level in Air Cleaner Dragging Brakes

Front
Wheels Out of Alignment
Tires
Improperly Inflated Inaccurate Odometer

Faulty
Fuel
Tank
Cap

Clogged
Muffler or Bent Exhaust Pipe

Lack
of Power
Low
Compression Ignition System (Timing Late)
Improper Functioning Carburetor or
Fuel
Pump

Fuel
Lines
Clogged
Air
Cleaner Restricted
Engine Temperature High Improper Tappet Clearance
Sticking Valves Valve Timing Late

Leaky
Gaskets
Muffler
Clogged
Bent Exhaust Pipe

Defective
Spark Plugs—Clean or Replace
Defective
Breaker Points—Replace
Points

Incorrect Breaker Point Gap—Reset
Points

Defective
Condenser or Coil—Replace
Loose Electrical Connections—Locate and Tighten
Broken Valve Spring—Replace Spring Broken Piston or Rings—Replace
Defective
Head Gasket—Replace Gasket
Cracked
Distributor Cap—Replace Cap

Low
Compression
Leaky
Valves
Poor Piston Ring Seal Sticking Valves
Valve Spring Weak or Broken
Cylinder
Scored or Worn
Tappet Clearance Incorrect
Piston Clearance too Large
Leaky
Cylinder Head Gasket
Burned Valves and
Seats
Sticking Valves or too Loose in Guides Improper Timing
Excessive Carbon Around Valve Head and Seat Overheating
Valve Spring Weak or Broken Burned Valves and Seats—Continued
Valve Tappet Sticking
Valve Tappet Clearance Incorrect
Clogged
Exhaust System
Valves Sticking Warped Valve Improper Tappet Clearance
Carbonized or Scored Valve
Stems
Insufficient Clearance Valve Stem to Guide
Weak or Broken Valve Spring Valve Spring Cocked Contaminated Oil
Overheating Inoperative Cooling System
Thermostat Inoperative Improper Ignition Timing
Improper Valve Timing
Excessive Carbon Accumulation

Fan
Belt too Loose

Clogged
Muffler or Bent Exhaust Pipe

Oil
System Failure
Scored or Leaky Piston Rings

Popping-Spitting-Detonation
Improper Ignition
Improper Carburetion
Excessive Carbon
Deposit
in Combustion
Cham­
bers
Poor Valve Seating Sticking Valves
Broken Valve Spring Tappets Adjusted too Close

Spark
Plug Electrodes Burned
Water or Dirt in
Fuel
Clogged
Lines Improper Valve Timing
Excessive Oil Comsumption Piston Rings Stuck in Grooves, Worn or Broken Piston Rings Improperly Fitted or Weak Piston Ring Oil Return
Holes
Clogged
Excessive Clearance, Main and Connecting Rod
Bearings

Oil
Leaks at Gaskets or Oil Seals
Excessive Clearance, Valve Stem to Valve Guide (Intake)

Cylinder
Bores Scored, Out-of-Round or Tapered Too Much Clearance, Piston to Cylinder Bore
Misaligned Connecting Rods
High Road
Speeds
or Temperature
Crankcase
Ventilator Not Operating
Bearing Failure
Crankshaft
Bearing Journal Out-of-Round

Crankshaft
Bearing Journal Rough

Lack
of Oil
Oil
Leakage
Dirty
Oil

Low
Oil Pressure or Oil Pump Failure
Drilled
Passages
in Crankcase or Crankshaft
Clogged

Oil
Screen Dirty Connecting Rod Bent 70

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

M
M-19.
SERVICE
DIAGNOSIS

SYMPTOMS
PROBABLE
REMEDY

Hard Steering
Lack
of
Lubrication
Lubricate
Tires
Soft.
. Inflate

Tight
Steering. Adjust. See "Steering" Section

Low Speed Shimmy
or
Wheel Fight
Spring
Clips and Shackles Loose
Front
Axle Shifted Insufficient Toe-In

Improper
Caster
Steering System Loose or Worn
Twisted Axle

High Speed Shimmy
or
Wheel Fight
Check
Conditions Under "Low Speed Shimmy"

Tire
Pressures Low or not
Equal

Wheel Out of Balance
Wheel Runout
Radial
Runout of Tires
Wheel Camber
Front
Springs
Settled
or Broken
Bent Steering Knuckle
Arm..................

Shock Absorbers not Effective
Steering
Gear
Loose on Frame

Front
Springs too Flexible

Tramp
Wheels Unbalanced

Wandering
Improper
Toe-in

Broken
Front Spring Main
Leaf

Axle Shifted Loose Spring Shackles or Clips
Improper
Caster

Tire
Pressure Uneven
Tightness in Steering System
Loose Wheel Bearings
Front
Spring
Settled
or Broken
Axle
Noisy
on
Pull
Pinion and Ring
Gear
Adjusted too Tight
Pinion Bearings Rough.

Axle Noisy
on
Coast
Excessive Back
Lash
at Ring and Pinion Gears.

End
Play in Pinion Shaft. . . Rough Bearing.

Axle Noisy
on
Coast
and
Pull
Ring
and Pinion Adjusted too Tight
Pinion Set too
Deep
in Ring
Gear
Pinion Bearing Loose or Worn

Back Lash
Axle Shaft Universal Joint Worn
Axle Shaft Improperly Adjusted

Worn
Differential Pinion Washers
Worn
Propeller Shaft Universal Joints.
Readjust
or Replace

Broken
Spring Center Bolt

Adjust
Reset

Adjust
or Overhaul Steering
Gear,
Front Axle or
Steering Parts
Straighten or Adjust
Inflate
Balance
Straighten Mount Properly
Same on Both Wheels
Repair
or Replace
Straighten or Replace
Replace or Repair Tighten

Over
Lubricated

Check
and Balance

Adjust—Check
for Bent Steering Knuckle Arm Replace

Spring
Center Bolt Broken
Adjust
or Replace
Reset Inflate

Adjust
Adjust
Repair
or Replace

Readjust

Replace

Readjust
Readjust

Replace

Readjust Readjust
Readjust
or Replace
Replace
Readjust

Replace

Repair

Emergency
Where difficulty is experienced with front axle differential making the vehicle inoperative,

remove
axle driving
flanges.
This will allow bringing vehicle in under its own power. Be sure the transfer
case
shift lever is in the neutral
(disengaged)
position.
285

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

O Note:
If the steering-gear-to-frame
bolts
are not

properly
torqued, they
will
eventually
loosen
dur­

ing operation of the vehicle. Loose
bolts
will
result
in
elongated
bolt
holes
making maintenance of bolt torque difficult, and may allow position of the
steering columns to be misaligned. Therefore,
proper
torquing is extremely important.
Do not tighten the steering gear to dampen out
steering trouble. Adjust the steering gear only to
remove lost motion or play within the unit.
0-5. Steering
Gear
Adjustment
The
cam and lever steering gear is illustrated in

Fig.
0-2. It consists of a
spiral
cam, and a cross shaft and lever assembly with two lever studs.
When
the steering wheel is turned, the cam
moves

the studs, causing rotary movement of the cross
shaft, which in
turn
causes angular movement of
the*steering arm.

Two
adjustments of the steering gear are necessary:
up and down play of the steering shaft, and adjust­ment of the lever studs (tapered pins) in the

cam
groove.

Adjustment
of the
ball
thrust bearings to eliminate up and down play of the steering shaft is ac­
complished by removing shims which are installed
between
the steering gear housing and the upper
cover. Before making this adjustment
loosen
the
housing side cover adjusting screw to free the pins
in
the cam groove. Loosen the housing cover to
cut and remove a shim or more as required.
Install
the screws and tighten. Adjustment should be
made to have a slight drag but allow the steering
wheel to
turn
freely with thumb and forefinger
lightly gripping the rim.

Shims
installed for adjustment are .002*, .003", and .010"
[.0508,
.0762
and .254 mm.] in thickness.

Adjustment
of the tapered pins in the cam
groove

is accomplished by adjusting screw. Unlock the

adjusting
screw and
turn
it in until a very slight
drag
is felt through the mid-position when turning
the steering wheel slowly from one extreme position
to the other.

Backlash
of the pins in the
groove
shows up as
end play of lever shaft, also as backlash of steer­ ing arm.

The
cam
groove
is purposely cut shallow in the

straight
ahead driving position for each pin.
This

feature permits a
close
adjustment for normal

straight
ahead driving and provides precision steer­ ing and permits take up of backlash at this point
after the wear occurs without causing a bind else­

where.
Always
adjust within the high range through
the mid-position of pin travel. Do not adjust off
"straight
ahead" position.
Backlash
in turned posi­
tions is not objectionable.
0-6.
Front
Wheel Alignment Adjustments
To
ensure correct alignment, a definite procedure
for inspection of the steering system is recom­ mended. It is
suggested
that the following sequence
be used:

a.
Equalize
tire pressures and level vehicle.
b.
Check
steering gear to steering column align­
ment.

c.
Inspect steering knuckle pivots, spindle, and
wheel bearing
looseness.

d.
Check
wheel runout.

e.
Test wheel balance and bearing adjustment.
f.
Check
for spring sag.
g.
Inspect brakes and shock absorbers.

h.
Check
steering gear assembly adjustment and
steering connecting rod.

i.
Check
caster,

j.
Check
toe-in.
k.
Check
toe-out
on turns.

I.
Check
camber.

m.
Check
tracking of front and
rear
wheels,

n.
Check
frame alignment.

The
factors of alignment, caster, camber, and toe-
in,
are all interrelated and if one adjustment is
made, another adjustment may be affected.
There­

fore, after an alignment job is completed, make a
complete recheck of all the adjustments to be sure
the
settings
are within the limit. Be sure all front
suspension and steering system nuts and
bolts
are

all
properly torqued before taking wheel alignment readings.

Proper
alignment of front wheels must be main­
tained in order to ensure
ease
of steering and satis­factory tire life.

The
most important factors of front wheel align­ment are wheel camber, axle caster and wheel
toe-in.

Wheel
toe-in is the distance the wheels are closer

together
at the front than at the
rear.
Wheel
camber is the amount the wheels incline out­

ward
at the top from a vertical position.
Front
axle caster is the amount in
degrees
that the
steering pivot pins are tilted towards the front or

rear
of the vehicle. Positive caster is inclination of
the top of the pivot pin towards the
rear
of the ve­

hicle.
Zero caster is the vertical position of the
pivot pin. Negative or reverse caster is the in­
clination
of the top of the pin towards the front
of the vehicle.

These
points should be checked at regular inter­
vals,
particularly when the front axle has been
subjected to a heavy impact. When checking wheel alignment, it is important that wheel bearings and

knuckle
bearings be in proper adjustment. Loose bearings
will
affect instrument readings when

checking
the camber, pivot pin inclination and
toe-in.
To
accurately check camber and caster, use a wheel
aligning fixture.
Camber
and caster of the front
wheels are both preset.
Camber
cannot be altered
but caster can be adjusted by installing caster shims
between
the axle pad and the springs. Wheel toe-in
may
be adjusted. To measure wheel toe-in, use a
wheel aligning fixture or follow the procedure given
in Par.
0-8.
0-7.
Front Wheel Toe-in
Toe-in
as illustrated in
Fig.
0-3, is necessary to
off­

set the
effect
of camber as shown in Fig. Q-4. 315

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

The
purpose of caster Fig. O-S, is to provide steer­
ing stability which
will
keep the front wheels in the
straight
ahead position and also assist in straighten­
ing up the wheels when coming out of a
turn.
Caster
of the front wheels is preset. If the angle of

caster,
when accurately measured, is found to be

incorrect,
correct it to the specification given at
the end of this section by either installing new

parts
or installing caster shims
between
the axle

pad
and the springs.

If
the camber and toe-in are correct and it is known
the the axle is not twisted, a satisfactory check

may
be made by testing the vehicle on the road.
Before road testing, make sure all tires are properly

inflated,
being particularly careful that both front
tires are inflated to exactly the same pressure.
If
vehicle turns easily to either side but is
hard
to
straighten out, insufficient caster for easy handling of vehicle is indicated. If correction is necessary, it

can
usually be accomplished by installing shims

between
the springs and axle pads to secure the
desired
result.
0-11-
Front
Wheel
Turning
Angle
When
the front wheels are turned, the inside wheel
on the
turn
travels in a smaller circle than the out­side wheel, therefore, it is necessary for the wheels
to toe out to prevent the tire on the inside wheel

frOm
being scuffed sideways.
This
angle for toe out
on turns is designed to permit both front wheels to

turn
on a common center by having the ends of the
steering
knuckle
arms closer
together
than the king­

pins.

To
avoid possible damage to the universal joints
on the front axles of 4-wheel drive vehicles, it is advisable to check the turning angle.
Wearing
away
of the upset
edge
on the spindle housing bolt which
10607

FIG.
0-6—TURNING
ANGLE
STOP
SCREW
1—Stop
Screw
contacts the
stop
screw
will
increase the turning
angle to the point where the universal joints may
be damaged.

The
Jeep Universal Series vehicles should have a

turning
angle of not more than 27^° both left and

right.
To adjust the
stop
screw, it is necessary to

loosen
the locknut holding the
stop
screw. When
the adjustment has been made, tighten the locknut
on the screw to prevent any movement. Refer to
Fig.
O 6.

The
left steering knuckle arm controls the relation­
ship of the front wheels on a left
turn
and the right
arm
controls the relation on a right
turn.

0-12. Steering
Knuckle
Arm

Should
a steering knuckle arm
become
bent, the

knuckle
housing must be replaced. It is not safe to
straighten the knuckle arm.
0-13.
Front
Wheel
Shimmy
Wheel
shimmy may be caused by various condi­
tions in the wheels, axle or steering system, or a
combination of
these
conditions. Outlined below

will
be found the usual corrections of this fault:

a.
Equalize
tire pressures and see that they are
according
to specifications.

b.
Check
the wheel bearings for
looseness.
Be sure
that the inner wheel bearing race is not too
loose
on the spindle.

c.
Remove both steering knuckles and carefully inspect the upper and lower king pin bearings.

Inspect
the bearing cups for evidence of brinelling,
pitting, or fretting. Any bearings that show the slightest imperfection must be
replaced.
Reassemble

and
lubricate the front axle and steering linkage,
installing
new steering knuckle oil seals if present
seals show any wear.

d.
With
full
weight on the front wheels and one

man
working the steering play with the steering
wheel, a second man should closely observe the steering bell
crank
for any rocking motion and the
double tie rod socket for any rocking motion or

looseness
at both points. Replace the complete bell
crank
assembly if it has even the slightest rocking motion. The same applies to the double tie rod
socket.
e.
Check
wheel run-out.
This
check should include
radial
run-out and wheel
looseness
on the hub.
f- Test wheel balance—check for blowout patches,
uniform
tire tread, vulcanized tires, mud on inside
of wheels, and tires creeping on the
rims.

g.
Try
switching front wheels and tires to the
rear,
criss-crossing
them in this operation.

h.
Check
for front
spring
sag. Also check for broken

spring
leaves, broken center
spring
bolt,
loose
spring

clips
(or tight clips), over-lubrication of spring leaves, spring shackle bracket
loose
on frame, and

loose
rear
spring shackle. Be sure that the shock
absorbers
are operating properly to eliminate bob­bing of the front end.

i.
Check
brakes to make sure that one
does
not

drag.

j.
Check
the steering assembly and steering con­ necting rod.
This
includes the up-and-down-play
of the steering worm shaft, end play of the cross 317