JEEP GRAND CHEROKEE 2004 WK / 3.G Owners Manual

If the liftgate flipper glass is open, connection to the rear
window wiper is interrupted preventing activation of the
rear wiper blade. When the liftgate flipper glass is closed,
the rear wiper switch or the ignition switch needs to be
turned OFF and ON to restart the rear wiper.
Adding Washer Fluid
The fluid reservoir for the windshield washers and the
rear window washer is shared. It is located in the front of
the engine compartment on the passenger side and
should be checked for fluid level at regular intervals. Fill
the reservoir with windshield washer solvent (not radia-
tor antifreeze) and operate the system for a few seconds
to flush out the residual water.
Rear Window Defroster
In the lower left of the climate control panel is a
push button for rear window defrosting. An am-
ber indicator in the push button will light when the
defroster is turned on. Push again to turn off the defroster
prior to an automatic time-out.
UNDERSTANDING YOUR INSTRUMENT PANEL 171
4

The defroster will automatically turn off after about ten
minutes. For about five more minutes of operation, push
the button again. To prevent excessive battery drain, use
the defroster only when the engine is operating. The push
button also activates the heated exterior mirrors, if so
equipped.CAUTION!
Use care when washing the inside of the rear win-
dow to prevent damage to heating elements. Use a
soft cloth and a mild washing solution, wiping
parallel to the heating elements. Also, keep all
objects a safe distance from the window to prevent
damaging the heating elements.
172 UNDERSTANDING YOUR INSTRUMENT PANEL

STARTING AND OPERATING
CONTENTS
mStarting Procedures.....................176
NNormal Starting......................176
NExtreme Cold Weather (Below ±20ÉF (±29ÉC) . . 177
NIf Engine Fails To Start.................177
NAfter Starting........................178
mEngine Block Heater Ð If Equipped.........178
mAutomatic Transmission..................179
NBrake Transmission Shift Interlock System
(BTSI).............................180NElectronically Controlled Five Speed Automatic
Transmission (4.7L Engine Only)..........180
NProtect Mode - Electronically Controlled
Transmission (4.7L Engine Only)..........180
NGear Ranges.........................181
NOver Temperature Mode................185
NTorque Converter Clutch................185
NRocking The Vehicle...................186
mFour-Wheel Drive Operation...............186
5

NSelec-TractOperating
Instructions/Precautions................186
NShift Positions........................188
NShifting Procedure....................189
NQuadra-Trac IItOperating
Instructions/Precautions Ð If Equipped.....191
NShift Positions........................192
NShifting Procedure....................193
NQuadra-DrivetSystem Ð If Equipped......194
mVari-Lok Front And Rear Axles Ð If Equipped . . 194
mParking Brake.........................194
mAnti-Lock Brake System..................197
mOn-Road Driving Tips...................199
mOff-Road Driving Tips...................200NWhen To Use 4 Lo (Low) Range...........200
NIn Snow, Mud And Sand................200
NHill Climbing........................200
NTraction Downhill.....................201
NAfter Driving Off-Road.................202
mTire Safety Information...................203
NTire Markings........................203
NTire Identification Number (TIN)..........206
NTire Loading And Tire Pressure...........207
mTires Ð General Information...............211
NTire Inflation Pressures.................212
NHigh Speed Operation.................213
NRadial-Ply Tires......................214
174 STARTING AND OPERATING

NTire Spinning........................214
NTread Wear Indicators..................215
NReplacement Tires.....................215
NAlignment And Balance.................217
mTire Pressure Monitor System Ð If Equipped . . . 217
NTire Pressure Monitor System Tire/Wheel
Rotation And Sensor Replacement Ð If
Equipped...........................218
NGeneral Information...................219
mTire Chains...........................220
mTire Rotation Recommendations............220
mFuel Requirements......................221
NReformulated Gasoline.................222
NGasoline/Oxygenate Blends..............222NMMT In Gasoline.....................223
NSulfur In Gasoline.....................223
NMaterials Added To Fuel................224
mFuel Tank Filler Cap (Gas Cap).............224
mTrailer Towing.........................226
NTrailer And Tongue Weight..............228
NCooling System TipsÐTrailer Towing.......229
NMinimum Vehicle Requirements For Trailer
Towing............................230
mRecreational Towing (Behind Motorhome, Etc.) . . 231
NShifting Into Neutral (N)................232
NShifting Out Of Neutral (N)..............233
mSnow Plow...........................234
STARTING AND OPERATING 175
5

STARTING PROCEDURES
Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belts.
WARNING!
Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build up may
cause serious injury or death.
The gear selector must be in the N (Neutral) or P (Park)
position before you can start the engine. Apply the brakes
before shifting to any driving gear.
Normal Starting
Normal starting of either a cold or a warm engine is
obtained without pumping or depressing the accelerator
pedal. Turn the key to the START position and release
when the engine starts. If the engine fails to start within
10 seconds, turn the key to the OFF position, wait 5
seconds, then repeat the normal starting procedure.
176 STARTING AND OPERATING

WARNING!
Never pour fuel or other flammable liquids into the
throttle body air inlet opening in an attempt to start
the vehicle. This could result in a flash fire causing
serious personal injury.
Extreme Cold Weather (below ±20ÉF (±29ÉC)
To insure reliable starting at these temperatures, use of an
externally powered electric engine block heater (available
from your authorized dealer) is recommended.
If Engine Fails to Start
If the engine fails to start after you have followed the
ªNormal Startingº or ªExtreme Cold Weatherº proce-
dures, it may be flooded. Push the accelerator pedal all
the way to the floor and hold it there while cranking the
engine. This should clear any excess fuel in case the
engine is flooded.NOTE:To prevent damage to the starter, do not crank
the engine for more than 15 seconds at a time. Wait 10 to
15 seconds before trying again.
If the engine has been flooded, it may start to run, but not
have enough power to continue running when the key is
released. If this occurs, continue cranking with the accel-
erator pedal pushed all the way to the floor. Release the
accelerator pedal and the key once the engine is running
smoothly.
If the engine shows no sign of starting after two 15±
second periods of cranking with the accelerator pedal
held to the floor, the ªNormal Startingº or ªExtreme Cold
Weatherº procedures should be repeated.
STARTING AND OPERATING 177
5

After Starting
The idle speed will automatically decrease as the engine
warms up.
CAUTION!
Long periods of engine idling, especially at high
engine speeds can cause excessive exhaust tempera-
tures which can damage your vehicle. Do not leave
your vehicle unattended with the engine running.
ENGINE BLOCK HEATER Ð IF EQUIPPED
The engine block heater warms engine coolant and
permits quicker starts in cold weather. Connect the cord
to a standard 110-115 volt AC electrical outlet with
grounded, three wire extension cord.
Use the heater when temperatures below 0ÉF (-18ÉC) are
expected to last for several days.The engine block heater cord is located:
²6-cylinder engine Ð bundled and fastened to the
injector rail between injectors 1 and 2.
²V-8 engine Ð coiled and strapped to the transmission
filler tube.
WARNING!
Remember to disconnect the cord before driving.
Damage to the 110-115 volt AC electrical cord could
cause electrocution.
178 STARTING AND OPERATING

AUTOMATIC TRANSMISSION
The pointer on the selector indicates the transmission
gear range (selector is illuminated for night driving).
Start the engine with the selector lever in N (Neutral) or
P (Park) position.NOTE:When the ignition is in the ON position, the
brake pedal must be pressed to move the gearshift lever
out of P (Park).
WARNING!
It is dangerous to shift the selector lever out of ªPº or
ªNº if the engine speed is higher than idle speed. If
your foot is not firmly on the brake pedal, the
vehicle could accelerate quickly forward or in re-
verse. You could lose control of the vehicle and hit
someone or something. Only shift into gear when
the engine is idling normally and when your right
foot is firmly on the brake pedal.
STARTING AND OPERATING 179
5

Brake Transmission Shift Interlock System (BTSI)
This vehicle is equipped with a brake transmission shift
interlock system (BTSI) that holds the gearshift lever in
the P (Park) position when the ignition switch is in an
unlocked position. To move the gear selector lever out of
the P (Park) position, the ignition switch must be turned
to the OFF, ON, or START position, the brake pedal and
the button on the front side of the shifter handle must be
depressed.
Electronically Controlled Five Speed Automatic
Transmission (4.7L Engine Only)
This electronically controlled transmission provides a
precise shift schedule. The transmission electronics are
self calibrating; therefore, the first few shifts on a new
vehicle may be somewhat abrupt. This is a normal
condition, and precision shifts will develop within a
couple hundred miles (kilometers).
Protect Mode - Electronically Controlled
Transmission (4.7L Engine Only)
This transmission is monitored electronically for abnor-
mal conditions. If an abnormal condition is detected, the
transmission's electronic controller will automatically
select direct gear (in the Drive position) or 2nd gear (in
the 2 or 1 position). This feature will allow the vehicle to
be driven to the dealer for service minimizing any
damage to the transmission. Some conditions that will
cause the transmission to use this alternate gear selection
are momentary and the transmission can be reset to the
normal shift program by performing the following:
²Stop the vehicle and shift into P (Park).
²Turn the ignition key to the OFF position and then
restart the engine.
²Shift into the desire shift range and resume driving.
180 STARTING AND OPERATING