light JEEP WRANGLER 2006 TJ / 2.G Owner's Guide

Blower Switch
The blower switch is the rotary knob to the left of the
controls. The blower speed will increase as the knob
is turned clockwise. There are four blower speeds.
NOTE: The blower motor will run until the mode
control knob is turned to the “Off” (“O”) position or the
ignition is turned OFF.
Temperature Control
The temperature control is the center knob located on the
climate controls. It controls the temperature of the air
delivered to the passenger compartment.
You can choose your degree of comfort by rotating the
knob. The coldest setting is to the extreme left (blue
region) and the warmest setting is to the extreme right
(red region).
Mode Selection
The mode selector is the right knob located on the climate
controls. It can be set in any of the following positions:
Off This position turns off the blower motor. In this
mode, there may be some slight air flow from the
floor outlets, side window outlets, and defrost outlet
located at the base of the windshield.
Panel Outside air comes from the outlets in the instrument
panel. Each of these outlets can be individually
adjusted to direct the flow of air. Also, a slight amount of
airflow may be noticed at the defrost outlet located at the
base of the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 173
4

Bi-Level Outside air comes from both instrument panel and
floor outlets. Also, a slight amount of airflow may
be noticed at the defrost outlet located at the base of the
windshield.
Floor Outside air comes from the floor outlets. Also, a
slight amount of airflow may be noticed at the
defrost outlet located at the base of the windshield.
Mix Outside air comes from the floor and defrost outlets
with air being directed through the demisters. This
mode works best in cold or snowy conditions. It
allows you to stay comfortable while keeping the wind-
shield clear. Defrost
Outside air comes from the windshield outlets
with a slight amount of air being directed through
the floor and demisters. Use this setting when necessary
to defrost or defog your windshield.
Air Conditioning — If Equipped
Blower Switch
The blower switch is the rotary knob to the left of the
controls. Turn the knob to the right to one of the four
positions to obtain the blower speed you desire.
NOTE: The blower motor will run until the mode
selector knob is turned to the “Off” (“O”) position or the
ignition is turned OFF.
Temperature Control
The temperature control is the center knob located on the
climate controls. It controls the temperature of the air
delivered to the passenger compartment.
174 UNDERSTANDING YOUR INSTRUMENT PANEL

Off Turning the rotary knob to this position shuts off the
blower motor and outside air will not come through
any outlet.
Recirculation Select this position when the outside air contains
smoke, odors, high humidity, or if rapid cooling is
desired. This feature allows for recirculation of
interior air only. Air flows through the panel outlets in
this mode. Also, a slight amount of airflow may be
noticed at the defrost outlet located at the base of the
windshield.
Panel Outside air flows through the air conditioning
system, and then through the outlets located in the
instrument panel. Also, a slight amount of airflow
may be noticed at the defrost outlet located at the base of
the windshield. Bi-Level
Outside air flows through the air conditioning
system, and then through the outlets located in the
instrument panel and those located on the floor. Also, a
slight amount of airflow may be noticed at the defrost
outlet located at the base of the windshield.
Panel Outside air comes from the outlets in the instrument
panel. Each of these outlets can be individually
adjusted to direct the flow of air. Also, a slight amount of
airflow may be noticed at the defrost outlet located at the
base of the windshield.
Floor Outside air comes from the floor outlets. Also, a
slight amount of airflow may be noticed at the
defrost outlet located at the base of the windshield.
176 UNDERSTANDING YOUR INSTRUMENT PANEL

WARNING!
Remember to disconnect the cord before driving.
Damage to the 110-115 volt AC electrical cord could
cause electrocution.
Use the heater when temperatures below 0°F (-18°C) are
expected to last for several days.
TRANSMISSION SHIFTING
6-Speed Manual Transmission
Follow the shift pattern on the gearshift knob.
NOTE: The backup lights will come on when your
vehicle is in reverse gear and the ignition is in the ON
position.Manual Shift Controls
STARTING AND OPERATING 185
5

When frequent transmission shifting occurs while using
Overdrive, such as when operating the vehicle under
heavy load conditions (for example, in hilly terrain,
strong head winds, or trailer towing), turning off over-
drive will improve performance and extend transmission
life by reducing excessive shifting and heat buildup. Overdrive can be locked out by pressing the O/D OFF
switch located on the instrument panel. The O/D OFF
indicator light (on the switch) will illuminate to show
that the switch has been activated. When the indicator
light is on, Overdrive is locked out. Pressing the switch a
second time restores the Overdrive function. The lockout
feature is useful when towing a trailer or carrying a
heavy load.
2 (Second)
For moderate grades and to assist braking on dry pave-
ment or in mud and snow. Begins at a stop in low gear
with automatic upshift to 2nd gear. Will not shift to 3rd.
1 (First)
For hard pulling at low speeds in mud, sand, snow, or on
steep grades. Begins and stays in low gear with no
upshift. Provides engine compression braking at low
speeds.
Overdrive Off Switch
192 STARTING AND OPERATING

NOTE:The transmission electronics constantly monitor
the transmission oil temperature. If the transmission gets
too hot, the transmission will change the way it shifts to
help control the condition. This may result in a slightly
different feeling or response during normal operation in
D (Drive) position. If the transmission becomes hot
enough, the TRANS TEMP warning light in the instru-
ment cluster will come on. After the transmission cools
down, it will return to normal operation.
Torque Converter Clutch
A feature designed to improve fuel economy has been
added to the automatic transmission of this vehicle. A
clutch within the torque converter engages automatically
at calibrated speeds. This may result in a slightly differ-
ent feeling or response during normal operation in high
gear. When the vehicle speed drops or during accelera-
tion, the clutch automatically and smoothly disengages.
FOUR–WHEEL DRIVE OPERATION
(COMMAND-TRAC™ OR ROCK-TRAC™) — IF
EQUIPPED
4WD Shift Controls
194 STARTING AND OPERATING

Operating Instructions/Precautions
The transfer case provides four mode positions — two
(rear) wheel drive high range, four wheel drive high
range, neutral, and four wheel drive low range.
This transfer case is intended to be driven in the two
wheel drive (2H) position for normal street and highway
conditions such as dry hard surfaced roads.
In the events when additional traction is required, the
transfer case 4H and 4L positions can be used to lock the
front and rear driveshafts together and force the front
and rear wheels to rotate at the same speed. This is
accomplished by simply moving the shift lever to these
positions. The 4H and 4L positions are intended for loose,
slippery road surfaces only. Driving in the 4H and 4L
positions on dry hard surfaced roads may cause in-
creased tire wear and damage to the driveline compo-
nents. The 4WD indicator light, located in the instrument panel,
alerts the driver that the vehicle is in four wheel drive
and that the front and rear driveshafts are locked to-
gether. This light illuminates when the transfer case is
shifted to either the 4H or 4L positions.
NOTE:
Do not attempt to make a shift while only the
front or rear wheels are spinning. The transfer case is not
equipped with a synchronizer and therefore the front and
rear driveshafts speeds must be equal for the shift to take
place. Shifting while only the front or rear wheels are
spinning can cause damage to the transfer case.
When operating your vehicle in 4L, the engine speed is
approximately three times that of the 2H or 4H positions
at a given road speed. Take care not to overspeed the
engine and do not exceed 25 mph (40 km/h).
STARTING AND OPERATING 195
5

slight application of the accelerator will supply maxi-
mum traction. When starting with only one rear wheel on
an excessively slippery surface, slight application of the
parking brake may be necessary to gain maximum trac-
tion.
WARNING!
On vehicles equipped with a limited-slip differen-
tial, never run the engine with one rear wheel off the
ground. The vehicle may drive through the rear
wheel remaining on the ground and cause you to
lose control of your vehicle.
AXLE LOCK (TRU–LOK™) — IF EQUIPPED
The Axle Lock switch is located on the lower center of the
instrument panel.
This feature will only activate when the following con-
ditions are met:
•Key in ignition, vehicle in 4L (Low) range.
Axle Lock Switch
STARTING AND OPERATING 199
5

•Vehicle speed should be 10 mph (16 km/h) or less.
To activate the system, press the switch once to lock the
rear axle only (the REAR LOCK indicator light will
illuminate), press the switch again to lock the front axle
(the FRONT LOCK indicator light will illuminate). Once
the rear axle is locked, pressing the switch again will lock
or unlock the front axle.
NOTE: The indicator lights will flash until the axles are
fully locked or unlocked. A chime will sound three times
and the indicator lights will continue to flash at a
different rate if the key is removed while the axles are still
in the locked position.
To unlock the axles, pull up on the switch.
Axle lock will disengage if vehicle is taken out of 4L
(Low) range.PARKING BRAKE
To set the parking brake, pull the lever up as firmly as
possible. When the parking brake is applied with the
ignition ON, the BRAKE warning light in the instrument
cluster will light.
NOTE: The BRAKE warning light indicates only that
the parking brake is applied. It does not indicate the
degree of brake application.
NOTE: If the parking brake is applied and the vehicle is
in motion, the BRAKE warning light will flash and a
chime will sound.
To release the parking brake, pull up slightly, press center
button, then lower lever completely.
200 STARTING AND OPERATING

If the parking brake is not completely released, the
BRAKE warning light will remain on.
NOTE: Your vehicle has automatically adjusting rear
brakes and we do not recommend any adjustment other
than the maintenance performed by your authorized
dealer.
Before leaving the vehicle parked on a hill, you must
make sure the parking brake is fully applied and place
the gear selector in the P (Park) position (automatic
transmission) or first gear (manual transmission). Make
certain the transfer case is in gear. Failure to do so may
cause the vehicle to roll and cause damage or injury.
Parking Brake Release
STARTING AND OPERATING 201
5