instrument cluster KIA EV6 2022 Features and Functions Guide

18*IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
ELECTRIC VEHICLE (EV) FEATURES
ELECTRIC VEHICLE (EV) F E AT U R E S
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Regenerative Braking - Paddle Switches, Drive Mode Video
Regenerative Braking - i-Pedal Video
QR CODE
Each of the different Drive Modes allows the regenerative braking level to be set at the driver ’s preference.
QUICK TIP
(Indicator on lower left corner of Instrument display)
Regenerative Braking with Paddle Switches
The regenerative braking system charges the battery when coasting or when you use the brakes to stop the vehicle. Use the paddle switches to adjust the regenerative braking level from 0 to 3 during decelerating or braking. The level will be displayed on the instrument cluster A.
•Pull the left paddle switch B to increase regenerative braking and deceleration
•Pull the right paddle switch C to decrease regenerative braking and deceleration
The paddle shifters do not operate when:
•Both paddle shifters are pulled at the same time
•The vehicle is decelerating by depressing the brake pedal
•Smart Cruise Control (SCC) is active
i-Pedal
i-Pedal driving controls the vehicle speed by the accelerator pedal, both acceleration and deceleration. To activate i-Pedal:
•Pull the left side paddle switch B to Level 3 regenerative braking (see indicator on Instrument Cluster)
•Then pull the left side paddle switch B once again when the regenerative braking level is set to Level 3
The i-Pedal indicator symbol will be illuminated on the instrument cluster.
+
-
96%Lv １READY
+
-
96%Lv １READY
For more information on regenerative braking, i-pedal driving or the Smar t Regeneration System, please refer to section 6 in the Owner ’s Manual.
A
BC
REMINDER: The driver ’s seat belt must be fastened to operate i-pedal driving.
Do not solely rely on i-pedal driving to stop the vehicle, as it may not be able to stop the vehicle depending on vehicle and road conditions. Always use pedal braking when necessar y. Pay at tention to the road condition ahead and apply the brake if necessar y.
+
-
96%Lv １READY
+
-
96%Lv １READY

19*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Regenerative Braking - Smart Regeneration Video
QR CODE
One-Pedal Driving
One-Pedal Driving increases the regenerative braking amount to above level 3 and may slow the vehicle down by pulling down the left switch.
•Pull and hold the left paddle switch B while coasting to activate One-Pedal Driving
•When the vehicle speed is above 2 mph, release the left paddle switch B for less than 0.5 seconds to return to the previously set level of regenerative braking
•When the vehicle speed is below 2 mph, One-Pedal Driving can stop the vehicle even though the left paddle switch is released
REMINDER: The driver ’s seat belt must be fastened to operate one-pedal driving.
Do not solely rely on one-pedal driving to stop the vehicle, as it may not be able to stop the vehicle depending on vehicle and road conditions. Always use pedal braking when necessar y and pay at tention to the road conditions ahead and apply the brake if necessar y.
Smart Regeneration System
This system automatically adjusts the regenerative braking level based on a vehicle being detected in front and road conditions.
•Activate Smart Regeneration in the Vehicle Settings on the Infotainment System by pressing SETUP on the screen, VEHICLE and ECO VEHICLE, and then SMART REGENER ATION. AUTO D will be displayed on the instrument cluster. AUTO regenerative brake adjusts regenerative braking based on the distance with the vehicle in front and its speed
•Pull and hold the right paddle switch C for more than 1 second to turn on/off the automatic change of the regenerative braking. The minimum regenerative braking level can be adjusted when in AUTO mode by using the left and right paddle switches
Smar t Regeneration is a supplemental system for the driver ’s convenience. Do not solely rely on this system to stop the vehicle or avoid collisions. Always cautiously look ahead to prevent unexpected or sudden situations.
Regenerative Braking with Paddle Switches (Continued)
ELECTRIC VEHICLE (EV) FEATURES
ELECTRIC VEHICLE (EV) F E AT U R E S
+
-
96%AUTO
READY
(Indicator on lower left corner of Instrument display)
D

21†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) Video
QR CODERear Cross-Traffic Collision-Avoidance Assist (RCCA)*†4
When engaged, RCCA is a supplemental system. Do not solely rely on this system and always pay at tention to the road and its conditions.
Refer to section 6 in the Owner ’s Manual for more information.
REMINDERS:
•
When vehicle power is cycled, RCCA will remain in the previous state
•
When a vehicle is approaching within the sensing range and coming up faster than 3 mph, the RCCA system will show a warning
RCCA Warning Volume can be adjusted in the Vehicle Set tings on the Infotainment System. Go to Driver Assistance, then Warning Volume.
QUICK TIP
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) is designed to warn the driver under certain conditions. It may activate the Electronic Stability Control (ESC) and temporarily apply braking if it detects cross traffic approaching the vehicle when the vehicle is in reverse.
When the RCCA rear-corner radar sensors detect approaching vehicles from the rear left or rear right side of the vehicle A, RCCA will sound a warning, the warning indicators on the outside rearview mirror will illuminate and a message will appear on the Instrument Cluster LCD B and the Infotainment System screen. If RCCA detects that the collision risk has increased, RCCA automatically applies the brakes to reduce your speed, potentially helping to minimize the effects of a possible collision.
RCCA is designed to operate under the following conditions:
•When the gear shift is in Reverse
•When the vehicle is moving slower than 6 mph
RCCA User Settings:
•To turn RCCA on, press the SETUP key/button on the Infotainment System. Select the VEHICLE button to enter the Vehicle Settings. Select DRIVER ASSISTANCE, PARKING SAFET Y, then REAR CROSS-TR AFFIC SAFET Y
•To set the warning timing, go to the Vehicle Settings, then go to Driver Assistance, then Warning Timing. Select one of the settings:
–
Early/Normal/Standard: Maximizes the amount of distance between the vehicles before the initial warning occurs
– Late: Reduces the amount of distance between the vehicles before the initial warning occurs
•The default Warning Timing is set to Normal. If the Warning Timing is changed, the warning time
of other Driver Assistance systems may also change
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
A
B

22†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Lane Keeping Assist (LK A) Video
QR CODE
When engaged, Lane Keeping Assist is not a substitute for safe driving and may not always warn the driver if the vehicle is driven outside of its lane. Always drive safely and use caution.
For illustrative purposes only. Your actual display, but tons and/ or features may var y.
Actual Vehicle Set tings steps may var y by model. Refer to section 5 in the Owner ’s Manual for more information.
REMINDERS:
•
LK A will not issue a warning if the turn signals or hazard lights are activated
•
When the ignition is cycled, LK A will return to the previously set state
Lane Keeping Assist (LKA)*†4
Lane Keeping Assist is designed to detect the lane markers on the road with a front view camera on the windshield, and may assist the driver ’s steering to potentially help keep the vehicle in the lane. When turned on, the instrument cluster indicator will initially illuminate white. It will remain white when the vehicle is traveling slower than 40 mph or when the system does not detect the lane markers. When the system detects the lane markers and can assist the steering, the LK A icon will illuminate green.
If LK A detects that you are moving outside of your lane, the system may give an audible warning and display a Lane Departure Warning on the instrument cluster. If the vehicle continues to move outside of the lane, LK A may provide steering inputs, trying to prevent the vehicle from moving outside its lane.
When LK A is enabled, press and hold the Lane Safety button A to turn LK A on or off.
LKA User Settings:
To enable LK A , press the SETUP key/button on the Infotainment System. Select the VEHICLE button to enter the Vehicle Settings. Select DRIVER ASSISTANCE then L ANE SAFET Y.
•Assist: LK A will automatically assist the driver ’s steering when lane departure is detected to help prevent the vehicle from moving out of its lane
•Warning Only: LK A will warn the driver with an audible warning when lane departure is detected. This mode does NOT provide any steering assist
•Off: LK A will turn off. The indicator light B will turn off on the cluster
All systems will operate under the following conditions:
•The vehicle speed exceeds approximately 40 mph
•LK A recognizes the lane the vehicle is traveling in
•The vehicle is between the lane markers
When the front-view camera detects the lane traveled in, both lanes are illuminated
When the front-view camera does not detect the lane traveled in the lanes are not illuminated
When the front-view camera detects the vehicle moving outside of the lane being traveled in, a yellow indicator will illuminate either on the left or right lane (shown in both images above)
The LK A Warning Volume can be adjusted in the Vehicle Set tings* on the Infotainment System
QUICK TIP
(But tons located on right side of steering wheel)
OKOKOK
OK
MODEMODEMODE
OKOK
MODEMODEMODE
OKOKOK
MODEMODEMODE
OKOKOK
MODEMODEMODE
A
0mph
0 KMH020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
#
"%7"/$&%
%3*7&3
"44*45"/$&
4:45&.4
"%"4

"%"4

23†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
Blind-Spot View Monitor (BVM)*†4
Blind-Spot View Monitor is designed to display the rear and side of the vehicle blind spot areas in the Instrument Cluster LCD A when the system is activated.
To turn BVM on press the SETUP key/button on the Infotainment System. Select VEHICLE, then Driver Assistance, then Blind-Spot Safety, and then Blind-Spot View.
When operating the turn signal B, BVM displays video of the blind-spot view for the direction indicated.
BVM will not operate when the Power button is off, a turn signal is deactivated or another warning screen comes up on the Instrument Cluster LCD.
When engaged, these systems are not substitutes for safe driving and may not always warn the driver if the vehicle is driven outside of its lane. Always drive safely and use caution.
Images are for illustrative purposes only and may not reflect actual feature or operation. See section 4 in the Owner ’s Manual for more information.
Images are for illustrative purposes only and may not reflect actual feature or operation. See section 6 in the Owner ’s Manual for more information.(LCD display showing right side of vehicle)
Safe Exit Assist (SEA)*†4
Safe Exit Assist can help prevent passengers from opening their door by displaying a warning message on the Instrument Cluster and sounding an audible warning when a vehicle is detected C, approaching from behind, after your vehicle has stopped.
SEA keeps the doors closed. When opening a door, SEA warns the driver of the risk of collision with a vehicle approaching the blind spot area.
In addition, when the Electronic Child Safety Lock button is in the LOCK position and an approaching vehicle from the rear area is detected, the Electronic Child Safety Lock button will not unlock the rear doors, even if the driver presses the button to open the doors.
To turn on SEA , press the SETUP key/button on the Infotainment System. Select VEHICLE, then select Driver Assistance, Blind-Spot Safety, and Safe Exit Assist.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
QR CODES
Blind-Spot View Monitor (BVM) Video
Safe Exit Assist (SEA) Video
0mph
P0 KMHAttention Level
020 4060202 m１00 kWh/ １00m268m96%Lv １READY66°F
High
Last Break
0:00
A
B
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
OFFAUTO
AUTO
OFFAUTO
AUTO
$

REMINDERS:
•
If the ignition is cycled, LFA returns to its previous state, on or off, if enabled and when combined with SCC . If using the Steering Wheel LFA but ton, then LFA defaults to off
•
LFA is not a substitute for safe and proper driving. Always drive safely and use caution
Lane Following Assist (LFA) is designed to help ensure that the vehicle stays centered in its lane A by monitoring the detected lane markings ahead and adjusting the steering. The instrument cluster indicator will initially illuminate white when turned ON, and on some vehicles, when SCC is engaged. It will remain white when the system does not detect the lane markers. When the system detects the lane markers and can assist the steering, the LFA icon will illuminate green B. When LFA is enabled in the Vehicle Settings, press the LFA button C briefly to turn LFA on or off.
Hands-off Warning - If the driver takes their hand off the Steering Wheel for several seconds, a warning message will appear on the Instrument Cluster, and an audible warning will sound. If hands-on Steering Wheel is not detected, LFA will cancel.
LFA will operate only when these conditions are met:
•LFA recognizes both sides of the lane markers the vehicle is traveling in
•
The vehicle is traveling slower than 110 mph
LFA User Settings:
•To enable LFA , press the SETUP key/button on the Infotainment System. Select the VEHICLE button to enter the Vehicle Settings. Select DRIVER ASSISTANCE, then L ANE SAFET Y(But ton located on steering wheel)
Images are for illustrative purposes only and may not reflect actual feature or operation.
LFA is supplemental. Do not solely rely on this system and always pay at tention to the road and its conditions.
Actual Vehicle Set tings steps may var y by model. See section 6 in the Owner ’s Manual for more detailed information, limitations and conditions.
When engaged, LFA is not a substitute for safe and proper driving. Always drive safely and use caution. LFA may not always aler t the driver when the vehicle is approaching another vehicle.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Lane Following Assist (LFA) Video
QR CODEOKOKOK
OK
MODEMODEMODE
OKOK
MODEMODEMODE
OKOKOK
MODEMODEMODE
OKOKOK
MODEMODEMODE
C
The LFA Warning Volume can be adjusted in the Vehicle Set tings in the Infotainment System.
QUICK TIP
24†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
0mph
0 KMH020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
"
#
-BOF
'PMMPXJOH
"TTJTU
-'"
*†4

Intelligent Speed Limit Assist (ISLA)*†4
Intelligent Speed Limit Assist is designed to use the information from the posted speed limit and the navigation system to inform the driver of the speed limit.
When ISL A is on and active, the system will display an alert on the Instrument Cluster LCD of the detected speed limit. If the vehicle’s current speed exceeds the detected speed limit, a warning will sound and the vehicle’s current speed will blink on the LCD.
ISLA User Settings:
•To enable ISL A on, press the SETUP key/button on the Infotainment System. Select the VEHICLE button to enter the Vehicle Settings. Select DRIVER ASSISTANCE, SPEED LIMIT, and then INTELLIGENT SPEED LIMIT ASSIST.
•Select one of the three modes:
- Speed Limit Assist: Informs the driver of the posted speed limit, displays a message to change the speed to help the driver stay within the posted speed limit
- Speed Limit Warning: Informs the driver of the posted speed limit A and warns the driver when the vehicle is traveling faster than the posted speed limit
- Off: ISL A is disabled
See section 6 in the Owner ’s Manual for more detailed information, limitations and conditions.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Intelligent Speed Limit Assist (ISLA) Video
QR CODE
You can set a speed limit offset to the posted speed limit by going to Vehicle Set tings, Driver Assistance, Speed Limit, then Speed Limit Offset. Set the offset to “0” if you want the vehicle to travel at the posted speed limit when ISL A is on.
QUICK TIPREMINDERS:
•
Vehicle must be parked and in a safe location to change the speed set tings
•
Additional information may be displayed if additional road sign information is detected
25†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
52mph
0 20 4060202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
D
A

Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Forward Collision-Avoidance Assist Video
QR CODE

FCA Warning Volume can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings* on the audio head unit. Go to Driver Assistance, then Warning Volume.
QUICK TIP
FCA is designed to detect and monitor a vehicle ahead or detect a pedestrian in the roadway through front view camera recognition and front radar signals to warn the driver that a collision is imminent and, if necessary, temporarily apply emergency braking. Initially, FCA provides Forward Collision Warning (FCW) when it detects a potential collision with a vehicle, pedestrian, or cyclist, emitting an audible warning and visual alert on the instrument cluster A.
If the system detects that the collision risk has increased, Forward Collision-Avoidance Assist (FCA) automatically applies the brakes to reduce your speed B, potentially helping to reduce the effects of a possible collision.
On select Kia models, when the driver responds to a potential collision with the Steering Wheel, Evasive Driver Steering Assist C will automatically assist to help prevent the collision. If the driver does not respond, then Evasive Driver Steering Assist may automatically turn the Steering Wheel to avoid the collision.
With the turn signal on, if it detects a potential collision, Junction Turning D may help to avoid the collision with an oncoming vehicle in an adjacent lane when turning left by applying emergency braking.
If it detects a potential collision, Junction Crossing E may help to avoid the collision with oncoming vehicles coming from the left or right side, when crossing an intersection, by applying emergency braking.
If it detects a potential collision, Lane-Change Oncoming F may help to avoid the collision with an oncoming vehicle coming when changing lanes by assisting the driver ’s steering.
If it detects a potential collision, Lane-Change Side G may help to avoid the collision with vehicles ahead when changing lanes by assisting the driver ’s steering.
Forward Collision-Avoidance Assist (FCA)†4
REMINDER: Once the risk factors are not detected, these functions will deactivate, and the driver must steer the vehicle.
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
For illustrative purposes only. Your actual display, but tons and/or features may var y.
26†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
(Junction Turning)
(Lane Changing – Oncoming Traffic)
(Junction Crossing)
(Lane Changing - Side)(Evasive Steering Assist)
0mph
0 KMH020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
Collision Warning
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
Emergency Braking
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
Collision Warning
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
Emergency Braking
A
B
CD
F
E
G

FCA User Settings:
•FCA is ON by default in most Kia models. FCA can be turned ON/OFF by going to the Vehicle Settings in the Infotainment System
•To enable FCA , press the SETUP key/button on the Infotainment System. Select the VEHICLE button to enter the Vehicle Settings. Select DRIVER ASSISTANCE, then FORWARD SAFETY. Then select one of the following modes:
– Active Assist: Vehicle will provide a warning (audible & visual) and may apply the brakes if needed
– Warning Only: Vehicle will provide a warning only (audible & visual)
– Off: System is off, no warnings or braking provided
•To adjust the FCA initial warning activation time, go to User Settings , Driver Assistance, Warning Timing, then select Normal or Late depending on your Kia model:
– Normal: This setting allows for a nominal amount of distance between the vehicles before the initial warning occurs
– Late: Reduces the amount of distance between the vehicles before the initial warning occurs
FCA/FCW will become active when the:
•Ignition is on or the Power button* is ON
•Vehicle is traveling faster than 5 mph
•Electronic Stability Control (ESC) is ON
Forward Collision-Avoidance Assist (FCA)†4 (Continued)
For ward Collision-Avoidance Assist (FCA) is not a substitute for safe driving and may not detect all objects in front of the vehicle. Always drive safely and use caution. Actual User Set tings steps may var y by model. Refer to section 4 in the Owner ’s Manual for more information.
REMINDERS:
•
FCA will be activated by default when the ignition is cycled ON, even when previous set ting was OFF
•
If FCA is operating and the ESC (Electronic Stabilit y Control) is turned off, FCA system is automatically turned off
•
When the FCA system is off, the FCA warning indicator is on in the Instrument Cluster
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
27†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
ADAS

28†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Highway Driving Assist (HDA) with Lane Change Assist Video
QR CODE
REMINDERS:
•
Current highway speeds and controlled or limited access road information may var y. Future navigation updates may change this information
•
If the driver changes the speed while in automatic speed set ting mode, it deactivates and enters a manual mode
•
When vehicle power is cycled, the system returns to its previous state, on or off
Highway Driving Assist (HDA)*†4
Highway Driving Assist (HDA) is designed to adjust the speed of the vehicle when driving on limited/controlled access highways/freeways. The system can adjust the vehicle’s speed based on available highway speed information. The automatic speed setting mode is designed to set the speed automatically by adjusting to the current speed limits of the highway the vehicle is traveling on.
If equipped, Highway Lane Change Assist may assist in changing lanes, if it detects the driver has turned on the lane change signal and if the lane change is possible.
When HDA is activated and the conditions are met, the Instrument Cluster indicator A will illuminate green. If proper conditions are not met, HDA will be in standby mode and the HDA indicator light B will illuminate gray. When in operation, and if both lanes are recognized, the Instrument Cluster will show the lanes illuminated white and the HDA indicator illuminated
green A.
If HDA is activated, conditions are met and the SCC speed is set by the driver (at the posted highway speed limit or slower), HDA will enter the automatic speed setting mode. The set speed and AUTO will be displayed B in green and an audible alert will sound.
HDA will operate only when these conditions are met:
•
The vehicle is traveling slower than 110 mph or the highway speed limit
•
When driving on limited/controlled access highways/freeways
•
When Smart Cruise Control (SCC) and Lane Following Asisst (LFA) are on and operating
•
When the SCC speed is set to the current posted highway speed or slower
HDA User Settings:
To enable HDA , Smart Cruise Control (SCC) and Lane Following Assist (LFA) must be on. Press the SETUP key/button on the Infotainment System, VEHICLE, DRIVER ASSISTANCE, DRIVER CONVENIENCE, then HIGHWAY DRIVING ASSIST.
When engaged, Highway Driving Assist is not a substitute for safe driving, may not detect all objects around the vehicle, and only functions on cer tain federal highways. Always drive safely and use caution.
See section 6 in the Owner ’s Manual for more detailed information, limitations and conditions.
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
0mph
0 KMH020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
60 MPH
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
60 MPHHDA
HDA
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
60 MPH
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
60 MPHHDA
HDA
A
B