ECU KIA Rio 2005 2.G User Guide

3-55
Trunk Lid (For 4 Door Coupe) To open the trunk, insert the key into the lock and
turn it clockwise until an audible “click” is heard.
 To close the trunk, use both hands to push the trunk
lid down until the lock “snaps’’ shut.
 Do not slam the trunk lid.
 Pull up on the trunk lid to make sure it is securely
latched.
To prevent premature wear or damage to the trunk lid
lift cylinders and attaching hardware, the trunk lid
must be fully closed before you drive your vehicle.
1B3104007E
Unlock
Key slot
If you must drive with the trunk lid open, keep the air
vents open so that additional outside air comes into the
vehicle.Remote Trunk Lid Release (If Equipped)The release is located at the left front corner of the dri-
ver’s seat on the floor. To open the trunk, pull up on
the lever.
WARNING -Exhaust Fumes
If you drive with the trunk lid open, you will
draw dangerous exhaust fumes into your vehi-
cle.
1B3104004C
RIO ENG CNA 3.qxd 7/29/05 5:13 PM Page 55

Knowing Your Vehicle3-583. Lift the hood and hold it open with the prop rod by
inserting the free end of the rod into the slot in the
hood.
1RS104013A
Closing the Hood Check the area under the hood to make certain all
filler caps are in place and that all loose items have
been removed.
 Secure the support rod in its clip.
 Lower the hood to about 30 cm (12 inches) height
and then let it drop to properly lock in place.
 Check to make sure the hood is closed.
WARNING
Hold the upper part wrapped in rubber of the
support rod. If you hold the other parts when
the support rod is heated by engine, you may
get burned.
CAUTION
Before closing the hood, make sure that all parts
and tools have been removed from the engine
area and that everyone is clear of the hood open-
ing.
RIO ENG CNA 3.qxd 7/29/05 5:13 PM Page 58

Knowing Your Vehicle3-60
(Continued)
 Do not get back into a vehicle once you have
begun refueling. Do not touch, rub or slide
against any item or fabric (polyester, satin,
nylon, etc.) capable of producing static elec-
tricity. Static electricity discharge can ignite
fuel vapors resulting in explosion. If you
must re-enter the vehicle, you should once
again eliminate potentially dangerous static
electricity discharge by touching a metal part
of the vehicle, away from the fuel filler neck,
nozzle or other gasoline source.
 When using a portable fuel container be sure
to place the container on the ground prior to
refueling. Static electricity discharge from the
container can ignite fuel vapors causing a
fire. Once refueling has begun, contact with
the vehicle should be maintained until the
filling is complete. Use only portable fuel con-
tainers designed to carry and store gasoline.
 Do not use cellular phones around a gas sta-
tion or while refueling any vehicle. Electric
current and/or electronic interference from
cellular phones can potentially ignite fuel
vapors causing a fire.
(Continued)
(Continued)
If you must use your cellular phone, use it in a
place away from the gas station.
 When refueling always shut the engine off.
Sparks produced by electrical components
related to the engine can ignite fuel vapors
causing a fire. Always insure that the engine
is OFF before and during refueling. Once
refueling is complete, check to make sure
the fuel filler cap and door are securely
closed, before starting the engine.
 Do not light any fire around a gas station.
DO NOT use matches or a lighter and DO
NOT SMOKE or leave a lit cigarette in your
vehicle while at a gas station especially dur-
ing refueling. Automotive fuel is highly
flammable and can, when ignited, result in
explosion by flames.
 If a fire breaks out during refueling, leave
the vicinity of the vehicle, and immediately
contact the manager of the gas station or
contact the police and local fire department.
Follow any safety instructions they provide.
RIO ENG CNA 3.qxd 7/29/05 5:13 PM Page 60

3-61
 To remove the cap, turn it counterclockwise.
 To install the cap, turn it clockwise until it “clicks.’’
This indicates that the cap is securely tightened.
✻ ✻
NOTICE
A loose fuel filler cap may cause the OBD-II
Malfunction Indicator Light ( ) light in the
instrument panel to illuminate unnecessarily.
Always ensure that the fuel filler cap is tight.
CHECK
CHECK
The fuel filler neck is designed to prevent filling the
fuel tank with anything but unleaded fuel.
If the fuel filler lid will not open in cold weather
because the area around it is frozen, push or lightly tap
the lid.
✻ ✻
NOTICE
If the fuel filler cap requires replacement, use
only a genuine Kia cap. An incorrect fuel filler
cap can result in a serious malfunction of the fuel
system or emission control system. Correct
replacement caps are available at Authorized Kia
Dealers.✻ ✻
NOTICE
Do not spill fuel on the exterior surfaces of the
vehicle. Any type of fuel on painted surfaces may
damage the paint.
AS2B03046A
RemoveInstall
Fuel filler
neck
RIO ENG CNA 3.qxd 7/29/05 5:13 PM Page 61

3-69
CAUTION
 Loading cargo or luggage weighing more than
110 lbs (50Kg) on the roof rack may damage
your vehicle. When you carry large objects,
never let them hang over the rear or the sides
of your vehicle.
 To prevent damage or loss to cargo as you are
driving, check occasionally to make sure the
luggage carrier and cargo are still securely
fastened.
 Always drive your vehicle at a moderate speed.
Roof Rack (If Equipped)Do not exceed the following specifications when load-
ing cargo or luggage.
1BC102006
Roof Rack 50Kg (110lbs)
RIO ENG CNA 3.qxd 7/29/05 5:13 PM Page 69

Driving Your Vehicle4-20
CAUTION
When stopped, do not use the gearshift lever in
place of the parking brake. Always set the park-
ing brake fully AND make sure the gearshift lever
is securely positioned in
P (Park) with an automatic transaxle or in
1st (First) or R (Reverse) gear with a manual
transaxle.
Parking Brake To set the parking brake, pull the parking brake
handle fully and firmly upward while applying the
service brake.
 To release the parking brake, pull the handle up
slightly and push the button. Then, lower the handle
to the released position while holding the button in.
1B3105001E1B315001F
CAUTION
Driving with the parking brake on will cause
excessive wear of the brake linings and pads.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 20

4-33 Door Ajar Warning
This warning light comes on when a door is not closed
securely with the ignition switch in any position.Anti-Lock Brake System (ABS)
Warning Light (if equipped)This light illuminates when you start the engine. The
light will go off if the ABS system is operating nor-
mally. Also, this light comes on if the key is turned to
ON, and then goes off in 2-3 seconds if the system is
operating normally.
If this warning light illuminates while the vehicle is
being driven, have the vehicle checked by an autho-
rized Kia Dealer as soon as possible.Rear Window Defroster Indicator This light comes on when the rear defroster is ON.Rear Hatch Warning Light
(5 door-if equipped)This warning light comes on when a rear hatch is not
closed securely with the ignition switch in any posi-
tion.
AS2B04020
LightingLighting ControlTo turn the lights on, twist the knob on the end of the
control lever which is located on the steering column
to the left of the steering wheel.
First position
Tail, parking, license and sidemarker lights and instru-
ment panel lights ON.
Second position
Head, tail, parking, license and sidemarker lights and
instrument panel lights ON.
ABS
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 33

6-11
Engine compartment
DESCRIPTION FUSE PROTECTED
RATING COMPONENT
Engine Compartment
(ABS) 15A ABS
RR FOG 10A Rear fog light (if equipped)
(F/FOG) 15A Front fog light (if equipped)
MAIN 80A Battery is not rechargeable
IG 1 30A (It will be automatically connect
ed to the secondary fuse.) CIGAR
10A, AUDIO 10A, IG COIL 15A,
TURN LAMP 10A, A/BAG 10A,
WIPER(RR) 15A, WIPER(FRT)
15A, RELAY 10A, START 10A
BLOWER 30A Heater
COOLING 30A Cooling fan
(ABS 1) 30A ABS
COND. FAN 20A Condenser fan
HEAD-HI 15A Head lamp high
HEAD-LOW 15A Head lamp low
EMS 10A Engine sensors
INJECTOR 15A Injector, 0
2sensor
F/PUMP 10A Fuel pump
ECU 10A Engine control unit, ECAT unit,
Main relay
RELAY 10A Blower motor, Power window,
Rear window defroster, Head
lamp(Airbag equipped vehicle)
(HLLD) 10A
-
*( ):Optional
STARTWINDOW
POWERFUEL
PUMPFRONT
FOGA/CON
HEAD
LAMPCOOL.FANHORN
TNS MAIN
IG 1 BLOWER
COOL ING(ABS 1) IG 2 COND.F
( )( ) ( )
( )
( )
COND.FAN
ROOM 15A
IG COIL
(ABS)
D/LOCK
BTN
P/WIN
(ABS 2)
RR DEF
HORN
TNS
RR FOG
(HLLD)(F/FOG)
HEAD
S/ROOF
MAIN
RELAY
RELAY
ECU
F/PUMP
INJECT
EMS
HEAD
LOW
HEAD
HI 15A
15A
25A
30A
30A
30A
25A
10A
15A
10A
10A
80A15A
25A
15A
25A
10A
10A
10A
15A
10A
15A
15A
MAIN
30A 30A 30A 30A 30A 20A
* USE THE DESIGNATED FUSE AND RELAY ONLY.
* REFER TO OWNER'S MANUAL FOR FUSE AND RELAY SERVICE.
* ( ) : OPTION
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 11

In Case Of An Emergency6-12DESCRIPTION FUSE PROTECTED
RATING COMPONENT
Engine compartment (continued)
MAIN RELAY 25A (It will be automatically connected
to the secondary fuse.)
EMS 10A, INJECTOR 15A,
F/PUMP 10A, ECU 10A
S/ROOF 15A Sunroof
HEAD 25A (It will be automatically connect
ed to the secondary fuse.)
HEAD-HI 15A, HEAD-LOW
15A, FOG LAMP(RR) 10A
IG 2 30A
TNS 15A (It will be automatically connect
ed to the secondary fuse.)
TAIL (LH) 10A, TAIL(RH) 10A
HORN 10A Horn
RR DEF 25A Rear window defroster
(ABS 2) 20A ABS
P/WIN 30A Power window
BTN 30A (It will be automatically connect
ed to the secondary fuse.)
MEMORY/ROOM 10A,
STOP 15A, HAZARD 15A
D/LOCK 25A Power door lock
IG COIL 15A Ignition coil
ROOM 15A Room LAMP, Audio,
Meterset, Warning sound
*( ): Optional
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 12

In Case Of An Emergency6-22
Once the lug nuts have been tightened, lower the
vehicle fully to the ground and continue to tighten the
lug nuts until they are completely secured.
If you are unsure of the tightness of the wheel lug nuts,
have them checked at the nearest service station. The
specified tightening torque is 103 N.
m (76 ft. lb.).
CAUTION
Your vehicle has metric threads on the wheel studs
and nuts. During wheel removal, make certain
that the same nuts removed are reinstalled - or, if
replaced, that nuts with metric threads and the
same configuration are used. Installation of a non-
metric thread nut on a metric stud or vice-versa
will not secure the wheel to the hub properly and
will damage the stud so that it must be replaced.
Be sure to use extreme care in checking for thread
style before installing aftermarket lug nuts or
wheels. If in doubt, consult an Authorized Kia
Dealer. Damaged studs may result in wheel loss
and personal injury.
10. Remove the lug nuts by turning them
counterclockwise, then remove the wheel.
11. Mount the spare tire into position and tighten the
nuts by hand. Install the lug nuts with the beveled
edge inward.
12. Turn the jack handle counterclockwise and lower
the vehicle until it touches the ground. Tighten the
lug nuts firmly in an “X’’ pattern.
3
2
4
1
1B3106002B
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 22