brake light KIA STONIC 2018 Owner's Manual

Page 263 of 523

CAUTION
The Emergency Stop Signal systemwill not work if the hazard warningflasher is already on.
Good braking practices
WARNING
•Whenever leaving vehicle or park‐ing, always set the parking brakeas far as possible and fully engagethe vehicle's transaxle into thepark position. Vehicles not fully en‐gaged in park with the parkingbrake set are at risk for moving in‐advertently and injuring yourselfor others.
•All vehicles should always have theparking brake fully engaged whenparking to avoid inadvertentmovement of the car which can in‐jure occupants or pedestrians.
• After parking the vehicle, check to besure the parking brake is not engaged
and that the parking brake indicator light is out before driving away. • Driving through water may get the
brakes wet. They can also get wet
when the car is washed. Wet brakes
can be dangerous! Your car will not
stop as quickly if the brakes are wet. Wet brakes may cause the car to pull
to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns
to normal, taking care to keep the car
under control at all times. If the brak‐ ing action does not return to normal,
stop as soon as it is safe to do so and
have your vehicle inspected by a pro‐
fessional workshop.
Kia recommends to call an authorized Kia dealer/service partner.
• Don't coast down hills with the car out of gear. This is extremely hazard‐
ous. Keep the car in gear at all times,
use the brakes to slow down, then
shift to a lower gear so that engine braking will help you maintain a safe
speed.
• Don't "ride" the brake pedal. Resting your foot on the brake pedal while
driving can be dangerous because it
can result in the brakes overheating and losing their effectiveness. It also
increases the wear of the brake com‐
ponents. • If a tire goes flat while you are driv‐
ing, apply the brakes gently and keepthe car pointed straight ahead while
you slow down. When you are moving
slowly enough for it to be safe to do
so, pull off the road and stop in a
safe place.
• If your car is equipped with an auto‐ matic transaxle, don't let your car
creep forward. To avoid creeping for‐
ward, keep your foot firmly on the
brake pedal when the car is stopped.
• Be cautious when parking on a hill. Firmly engage the parking brake andplace the shift lever in P (Park). If
your car is facing downhill, turn the
front wheels into the curb to help
keep the car from rolling. If your car is facing uphill, turn the front wheels
away from the curb to help keep the
car from rolling. If there is no curb or
if it is required by other conditions to
keep the car from rolling, block the wheels.

6-41
6
Driving your vehicle

Page 265 of 523

CRUISE CONTROL SYSTEM (IF EQUIPPED)
The cruise control system allows you to
program the vehicle to maintain a con‐
stant speed without pressing the accel‐ erator pedal.
This system is designed to function
above approximately 30 km/h (20
mph).
WARNING
•If the cruise control is left on,(CRUISE indicator light in the in‐strument cluster illuminated) thecruise control can be switched onaccidentally. Keep the cruise con‐trol system off (CRUISE indicatorlight OFF) when the cruise controlis not in use, to avoid inadvertent‐ly setting a speed.
•Use the cruise control system onlywhen traveling on open highwaysin good weather.
(Continued)
(Continued)
•Do not use the cruise control whenit may not be safe to keep the carat a constant speed, for instance,driving in heavy or varying traffic,or on slippery (rainy, icy or snow-covered) or winding roads or over6% uphill or down-hill roads.
•Pay particular attention to thedriving conditions whenever usingthe cruise control system.
CAUTION
During cruise-speed driving of amanual transaxle vehicle, do notshift into neutral without depressingthe clutch pedal, since the enginewill be over-revved. If this happens,depress the clutch pedal or releasethe cruise control ON-OFF switch.
NOTICE
During normal cruise control opera‐
tion, when the SET switch is activa‐
ted or reactivated after applying the
brakes, the cruise control will ener‐
gize after approximately 3 seconds.
This delay is normal.
NOTICE
To activate cruise control, depress
the brake pedal at least once after
turning the ignition switch to the ON
position or starting the engine. This
is to check if the brake switch which
is important part to cancel cruise
control is in normal condition.

6-43
6
Driving your vehicle

Page 267 of 523

¥5ZQF$
1. Press the cruise /CRUISE/ but‐
ton on the steering wheel, to turn
the system on. The cruise indicator
light will illuminate.
2. Accelerate to the desired speed, which must be more than 30 km/h
(20 mph).
NOTICE
nManual transaxle
For manual transaxle vehicles, you
should depress the brake pedal at
least once to set the cruise control
after starting the engine.
¥5ZQF"
¥5ZQF#3. Move the lever down (to SET-), and release it at the desired speed. The
cruise set indicator light will illumi‐
nate. Release the accelerator pedal
at the same time. The desired
speed will automatically be main‐
tained.
On a steep grade, the vehicle may slow
down or speed up slightly while going downhill.

6-45
6
Driving your vehicle

Page 270 of 523

¥5ZQF$
• Depress the brake pedal.
• Depress the clutch pedal if equippedwith a manual transaxle.
• Shift into N (Neutral) if equipped with an automatic transaxle.
• Press the O/CANCEL switch located on the steering wheel.
• Decrease the vehicle speed lower than the memory speed by 20 km/h
(12 mph).
• Decrease the vehicle speed to less than approximately 30 km/h (20
mph).
Each of these actions will cancel cruise
control operation (the cruise set indica‐tor light will go off), but it will not turn the system off. If you wish to resume cruise control operation, move up thelever (to RES+) located on your steering wheel. You will return to your previous‐ly preset speed.To resume cruising speed at
more than approximately 30
km/h (20 mph):
¥5ZQF"
¥5ZQF#
Driving your vehicle
6-48

Page 279 of 523

NOTICE
•Do not install any accessories,
such as license plate molding or
sticker, on the sensor area. Nor ar‐
bitrarily replace the bumper.
Those may adversely affect the
sensing performance.
•Always keep the sensor/bumper
area clean.
•Use only soft clothes to wash the
vehicle. Also, do not spray highly-
pressurized water on the sensor
installed on the bumper.
•Be careful not to apply unnecessa‐
ry force on the frontal sensor
area. When the sensor moves out
of the correct position due to ex‐
ternal force, the system may not
normally operate even without the
warning light or message. In this
case, have the vehicle inspected by
a professional workshop. Kia rec‐
ommends to visit an authorized
Kia dealer/service partner.
(Continued)
(Continued)
•Use only the genuine Kia sensor
cover. Do not arbitrarily apply
paint on the sensor cover.
System malfunction
0:#-
• When the FCA is not working proper‐ly, the FCA warning light () will illu‐
minate and the warning message will
appear for a few seconds.
After the message disappears, the
master warning light (
) will illumi‐
nate. In this case, have the vehicle in‐
spected by a professional workshop.
Kia recommends to visit an author‐
ized Kia dealer/service partner. • The FCA warning message may ap‐
pear along with the illumination of
the ESC warning light.
WARNING
•The FCA is only a supplementalsystem for the driver’s conven‐ience. The driver should hold theresponsibility to control the vehicleoperation. Do not solely depend onthe FCA system. Rather, maintaina safe braking distance, and, ifnecessary, depress the brake ped‐al to lower the driving speed.
•The FCA may unnecessarily pro‐duce the warning message and thewarning alarms. Also, due to thesensing limitation, the FCA maynot produce the warning messageand the warning alarm at all.
•When there is a malfunction withthe FCA, the braking control doesnot operate upon detecting a colli‐sion risk even with other brakingsystems normally operating.
(Continued)

6-57
6
Driving your vehicle

Page 280 of 523

(Continued)
•The FCA operates only for the ve‐hicle / pedestrian in front, whiledriving forward. It does not oper‐ate for any animals or vehicles inthe opposite direction.
•The FCA does not recognize thevehicle, which horizontally drivesacross the crossroad, or the vehi‐cle, which is parked in the horizon‐tal direction.
Limitation of the system
The FCA is an assistant system for a
driver in a certain risky driving condition
and it does not take every responsibili‐ ty for all risks from driving condition.
The FCA monitors the driving situations
through the radar and the camera sen‐
sor. Thus, for a situation out of the sensing range, the FCA may not nor‐
mally operate. The driver should pay
great caution in the following situa‐ tions. The FCA operation may be limi‐
ted.
Recognizing vehicles
- The radar or the camera is contami‐
nated with foreign substances.
- It heavily rains or snows. -
There is interruption by electric
waves.
- There is severe irregular reflection
from the radar.
- The vehicle in front has a narrow
body. (i.e. motor cycle and bicycle)
- The driver’s view is unclear due to
the backlight, the reflected light, or
darkness.
- The camera cannot contain the full
image of the vehicle in front.
- The vehicle in front is a special vehi‐
cle, such as a heavily-loaded truck or
a trailer.
The vehicle in front does not turn ON
the rear lights, does not have rear
lights, has asymmetric rear lights, or
has rear lights out of angle.
- The outside brightness is greatly
changed, such as entering/exiting the tunnel.
- The vehicle driving is unstable.
- The radar/camera sensor recognition
is limited.
- Driving on unpaved and uneven road
surfaces, or through sudden gradient changes. -
In construction zones or on railroad
tracks, or there are metallic objects
on the road.
- Driving indoors such as in an under‐
ground parking lot.
- Driving on a curve
The FCA performance decreases
while driving on a curve. The FCA may
not recognize the vehicle in front even in the same lane. It may unnec‐
essarily produce the warning mes‐
sage and the warning alarm, or it
may not produce the warning mes‐
sage and the warning alarm at all.
While driving on a curve, pay great caution, and, if necessary, depress
the brake pedal.
Driving your vehicle
6-58

Page 298 of 523

ECONOMICAL OPERATION
Your vehicle's fuel economy depends mainly on your style of driving, where
you drive and when you drive.
Each of these factors affects how
many kilometers (miles) you can get from a liter (gallon) of fuel. To operate
your vehicle as economically as possi‐
ble, use the following driving sugges‐ tions to help save money in both fuel
and repairs: • Drive smoothly. Accelerate at a mod‐ erate rate. Don't make "jackrabbit"
starts or full-throttle shifts and maintain a steady cruising speed.
Don't race between stoplights. Try to
adjust your speed to the traffic so
you don't have to change speeds un‐
necessarily. Avoid heavy traffic whenever possible.
Always maintain a safe distance from
other vehicles so you can avoid un‐
necessary braking. This also reduces
brake wear.
• Drive at a moderate speed. The fast‐ er you drive, the more fuel your vehi‐cle uses. Driving at a moderate
speed, especially on the highway, is
one of the most effective ways to re‐
duce fuel consumption. • Don't "ride" the brake pedal. This can
increase fuel consumption and also
increase wear on these components.
In addition, driving with your foot
resting on the brake pedal may cause
the brakes to overheat, which re‐ duces their effectiveness and may
lead to more serious consequences.
• Take care of your tires. Keep them inflated to the recommended pres‐
sure. Incorrect inflation, either too
much or too little, results in unneces‐ sary tire wear. Check the tire pres‐
sures at least once a month.
• Be sure that the wheels are aligned correctly. Improper alignment can re‐
sult from hitting curbs or driving too fast over irregular surfaces. Poor
alignment causes faster tire wear
and may also result in other prob‐
lems as well as greater fuel con‐
sumption.
• Keep your car in good condition. For better fuel economy and reduced
maintenance costs, maintain your car
in accordance with the maintenance
schedule in L

Page 300 of 523

SPECIAL DRIVING CONDITIONS
Hazardous driving conditions
When hazardous driving conditions are
encountered such as water, snow, ice, mud, sand, or similar hazards, follow
these suggestions: • Drive cautiously and allow extra dis‐ tance for braking.
• Avoid sudden braking or steering.
• When braking with non-ABS brakes pump the brake pedal with a light up-
and-down motion until the vehicle is stopped.
WARNING
nABS
Do not pump the brake pedal on avehicle equipped with ABS.
• If stalled in snow, mud, or sand, use second gear. Accelerate slowly to
avoid spinning the drive wheels.
• Use sand, rock salt, tire chains, or other non-slip material under the
drive wheels to provide traction when
stalled in ice, snow, or mud.
WARNING
nDownshifting
Downshifting with an automatictransaxle, while driving on slipperysurfaces can cause an accident. Thesudden change in tire speed couldcause the tires to skid. Be carefulwhen downshifting on slippery sur‐faces.
Rocking the vehicle
If it is necessary to rock the vehicle to
free it from snow, sand, or mud, first turn the steering wheel right and left
to clear the area around your front
wheels. Then, shift back and forth be‐ tween 1st (First) and R (Reverse) in ve‐
hicles equipped with a manual transaxle
or R (Reverse) and any forward gear in
vehicles equipped with an automatic transaxle. Do not race the engine, and
spin the wheels as little as possible. If
you are still stuck after a few tries, have the vehicle pulled out by a tow ve‐
hicle to avoid engine overheating and
possible damage to the transaxle.
CAUTION
Prolonged rocking may cause engineover-heating, transaxle damage orfailure, and tire damage.
WARNING
nSpinning tires
Do not spin the wheels, especially atspeeds more than 56 km/h (35mph). Spinning the wheels at highspeeds when the vehicle is station‐ary could cause a tire to overheatwhich could result in tire damagethat may injure bystanders.
NOTICE
The ESC system (if equipped) should
be turned OFF prior to rocking the
vehicle.
Driving your vehicle
6-78

Page 302 of 523

• Keep your headlights clean and prop‐erly aimed on vehicles not equipped
with the automatic headlight aiming feature. Dirty or improperly aimed
headlights will make it much more
difficult to see at night.
• Avoid staring directly at the head‐ lights of oncoming vehicles. You could
be temporarily blinded, and it will take several seconds for your eyes to
readjust to the darkness.Driving in the rain
Rain and wet roads can make driving
dangerous, especially if you’re not pre‐ pared for the slick pavement. Here are
a few things to consider when driving in
the rain: • A heavy rainfall will make it harder to see and will increase the distanceneeded to stop your vehicle, so slow
down.
• Keep your windshield wiping equip‐ ment in good shape. Replace your
windshield wiper blades when they show signs of streaking or missing
areas on the windshield. • If your tires are not in good condition,
making a quick stop on wet pave‐
ment can cause a skid and possibly
lead to an accident. Be sure your tires are in good shape.
• Turn on your headlights to make it easier for others to see you.
• Driving too fast through large pud‐ dles can affect your brakes. If you
must go through puddles, try to drive
through them slowly.
• If you believe you may have gotten your brakes wet, apply them lightly
while driving until normal braking op‐
eration returns.Driving in flooded areas
Avoid driving through flooded areas un‐
less you are sure the water is no higher than the bottom of the wheel hub.
Drive through any water slowly. Allow
adequate stopping distance because brake performance may be affected.
After driving through water, dry the
brakes by gently applying them several
times while the vehicle is moving slow‐ ly.
Driving your vehicle
6-80

Page 307 of 523

To keep locks from freezing
To keep the locks from freezing, squirt
an approved de-icer fluid or glycerine
into the key opening. If a lock is covered with ice, squirt it with an approved de-
icing fluid to remove the ice. If the lock
is frozen internally, you may be able to thaw it out by using a heated key. Han‐
dle the heated key with care to avoid
injury.
Use approved window washer
anti-freeze in system
To keep the water in the window wash‐
er system from freezing, add an ap‐ proved window washer anti-freeze sol‐
ution in accordance with instructions on
the container. Window washer anti- freeze is available from an authorized
Kia dealer/service partner and most au‐
to parts outlets. Do not use engine
coolant or other types of anti-freeze asthese may damage the paint finish.
Don't let your parking brake
freeze
Under some conditions your parking brake can freeze in the engaged posi‐
tion. This is most likely to happen when
there is an accumulation of snow or ice around or near the rear brakes or if the
brakes are wet. If there is a risk the
parking brake may freeze, apply it only temporarily while you put the shift lev‐
er in P (automatic transaxle) or in first
or reverse gear (manual transaxle) and block the rear wheels so the vehicle
cannot roll. Then release the parking
brake.
Don't let ice and snow
accumulate underneath
Under some conditions, snow and ice
can build up under the fenders and in‐ terfere with the steering. When driving
in severe winter conditions where this
may happen, you should periodically check underneath the car to be sure
the movement of the front wheels and
the steering components is not ob‐ structed.
Carry emergency equipment
Depending on the severity of the
weather, you should carry appropriate
emergency equipment. Some of the items you may want to carry include
tire chains, tow straps or chains, flash‐
light, emergency flares, sand, shovel, jumper cables, window scraper, gloves,
ground cloth, coveralls, blanket, etc.

6-85
6
Driving your vehicle

Page:   < prev 1-10 11-20 21-30 31-40 next >