Engine control LAMBORGHINI GALLARDO 2009 Owner's Manual
Page 212 of 1659
13
L714 01 00 03
Fig.17
C
F
' (
(
A
%
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
Remove the engine wiring harness. •Disassemble the bench (086803).
• Disassemble the right side member cover (086803).
• Disassemble the right B pillar cover (086803).
21. Disconnect the E-gear control unit connectors ( A-Fig.17) and loosen the corresponding earth ( % ) L J ). Only
for vehicles equipped with an E-gear system.
22. Disconnect the connections of the 4 relays ( C-Fig.17) connected to the main electrical system.
23. Detach the 2 fuse blocks ( ' ) L J ) from the corresponding support.
24. Loosen the 2 screws ( ( ) L J ) securing the relay support ( F-Fig.17) to the chassis.
25 . Disconnect the 7 relays on the support ( F-Fig.17).
1- Blue 643 main relay.
2- Gray 643 secondary air pump relay.
3- Purple 373 +50 1 relay.
4- Red 373 +50 2 relay.
5- Orange 643 secondary air pump 1 relay.
6- Green 643 engine relay.
7- White 179 E-gear pump relay (only on vehicles equipped with an E-gear system).
8- Blank.
9- Blank.
26. Disconnect the 3 fuses on the relay support ( F-Fig.17).
A- Black - 50A secondary air pump 1.
B- Brown - 40A fuel pump supply.
C- Blank.
D- Red - 50 A secondary air pump 2.
Page 215 of 1659
16
L714 01 00 03
Fig.20
1
1
O
3
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
32. 5 H O H D V H W K H L Q M H F W L R Q F R Q W U R O X Q L W 1 ) L J ) on the left side of the passenger compartment by loosening the two
E U D F N H W ¿ [ L Q J V F U H Z V O-Fig.20).
33. Loosen the clamp ( 3 ) L J ) securing the engine wiring harness to the chassis.
34. Position the control unit ( 1 ) L J ) on the engine.
Page 290 of 1659
1
L714 01 21 03
Fig.1
C
A
B
B
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
$ ' L V D V V H P E O L Q J W K H Z D W H U F R R O L Q J F L U F X L W W D Q N Q R X U L F H 3 U H O L P L Q D U \ R S H U D W L R Q V • Empty the engine coolant circuit .
• Disassemble the rear hood support piston .
• Disassemble the right side bulkhead .
• Release the right engine injection control unit (MASTER) .
' L V D V V H P E O L Q J W K H W D Q N1.
Disconnect the coolant level connector( A-Fig.1 ).
2. Disconnect the 4 pipes ( B-Fig.1) connected to the tank ( C-Fig.1).
7 K L V V H F W L R Q H [ S O D L Q V K R Z W R G L V D V V H P E O H
$ : D W H U F R R O L Q J F L U F X L W W D Q N Q R X U L F H
B) Cooling circuit radiator
C) Radiator fan
' : D W H U S L S H V
Page 310 of 1659
2
L714 01 21 05
Fig.3
H
I
G
G
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
3. Connect the 4 pipes ( G-Fig.3) to the tank ( H-Fig.3).
4.
Connect the coolant level connector( I-Fig.3 ).
• Fill the engine coolant circuit .
• Secure the right engine injection control unit (MASTER) .
• Assemble the right side bulkhead .
• Assemble the rear hood support piston .
Page 327 of 1659
1
L714 01 21 08
Fig.1
A
Fig.2
B
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
& 2 2 / $ 1 7 ) , / / , 1 *
) L O O W K H F R R O D Q W W D Q N Z L W K W K H H Q J L Q H R I I D Q G Z D L W I R U W K H H Q J L Q H W R F R P S O H W H O \ F R R O G R Z Q 7 K H F R R O L Q J F L U F X L W L V X Q G H U S U H V V X U H ' R Q R W R S H Q W K H F R R O D Q W W D Q N F D S Z L W K W K H H Q J L Q H E R L O L Q J K R W U L V N
of burns!
1. Unscrew the plug ( A-Fig.1) of the expansion tank and top up with the prescribed type of coolant (000300) up to
50 ÷ 60 mm from the base of the cap.
2. Start the engine and run it at idle speed for some minutes leaving the radiator expansion tank plug open.
3. Adjust the air conditioner control to maximum heat and maximum fan speed (B-Fig.2); stop the engine and
check the coolant level through the radiator expansion tank plug; top up with coolant if necessary.
4. Close the cap
5. Wait for the engine to cool down (to below 80°C) and top up the coolant tank (Nourice) with the missing coolant.
6. Then tighten the radiator expansion tank plug.
Page 338 of 1659
1
L714 01 28 00
Fig.1
A
A
B
® Automobili Lamborghini S.p.A.
/ H S U R F H G X U H H O H L Q I R U P D ] L R Q L S X E E O L F D W H G L V H J X L W R V R Q R V W U H W W D P H Q W H F R Q ¿ G H Q ] L D O L H U L Y R O W H H V F O X V L Y D P H Q W H D O O D 5 H W H ' H D O H U H 6 H U Y L F H 3 R L Q W $ X W R U L ] ] D W L / D P E R U J K L Q L 7 X W W L L G L U L W W L G ¶ D X W R U H V R Q R S U R S U L H W j
G L $ X W R P R E L O L / D P E R U J K L Q L 6 S $ L Q E D V H D O O D O H J J H V X L G L U L W W L G ¶ D X W R U H 7 X W W L L F D S L W R O L 3 ' ) G L F X L V L F R P S R Q J R Q R L P D Q X D O L R I ¿ F L Q D : ( % G H V F U L W W L G L V H J X L W R V L E D V D Q R V X O O H L Q I R U P D ] L R Q L G L V S R Q L E L O L D O
P R P H Q W R G H O O D S X E E O L F D ] L R Q H & R Q U L V H U Y D G L D J J L R U Q D P H Q W R H P R G L ¿ F K H 6 R Q R Y L H W D W H O D U L V W D P S D O D U L S U R G X ] L R Q H O ¶ L Q R O W U R D S H U V R Q H Q R Q D X W R U L ] ] D W H H R D W H U ] H S H U V R Q H O D W U D G X ] L R Q H D Q F K H S D U ] L D O H
V H Q ] D O ¶ D X W R U L ] ] D ] L R Q H V F U L W W D G D S D U W H G L $ X W R P R E L O L / D P E R U J K L Q L 6 S $
* H Q H U D O G H V F U L S W L R Q R I W K H G L U H F W L Q M H F W L R Q V \ V W H P ' , 6
The
G L U H F W L Q M H F W L R Q V \ V W H P ' , 6 is comparable to the running of an indirect injection engine. The basic difference
is that in this case, the fuel is injected directly into the cylinder.
This system better optimizes the amount of fuel to be injected, so consumption – and consequently emissions – are reduced. Characteristics of the system • A low pressure pump having an operation range between 6 and 4 bar,
• 7 Z R L Q W D N H P D Q L I R O G V H T X L S S H G Z L W K W Z R D L U À R Z P H W H U V W K D W P H D V X U H W K H À R Z D Q G W H P S H U D W X U H R I W K H D V S L U D W H G
air (one per manifold),
• Two high pressure pumps mechanically driven by the motion of the engine can reach a pressure varying
between E D U 0 , 1 D Q G E D U 0 $ ; .
• High pressure injectors that directly inject the fuel into the cylinder crown.
• A special piston that allows a vortex to be created, inside of which the fuel vaporized at high pressure is
sprayed.
The system is designed for the following types of operation: • V W R L F K L R P H W U L F V W U D W L ¿ H G P L [ W X U H
• homogeneous mixture,
• homogeneous and rich mixture.
, Q R X U V S H F L ¿ F F D V H homogeneous operation is used:
I U R P W R U S P L Q V W R L F K L R P H W U L F V W U D W L ¿ H G P L [ W X U H H V S H F L D O O \ D W O R Z V S H H G V D Q G G X U L Q J W K H L J Q L W L R Q S K D V H V W R
help with emissions.Homogenous and rich running is used only when there is a demand for torque.
When running at low speeds, the injection system is further aided by a tumble system inside the intake manifold that
helps the vortex created by the design of the piston, ensuring that the quantity of injected fuel goes directly beneath the spark plug. In this way the mixture is optimized with a lower quantity of fuel.
The injection of fuel during the compression phase of the cylinder is managed electronically by two injection control
units, of which one works as the MASTER and the other as the SLAVE .
The injection system is controlled by two linear oxygen sensors that alter the amount of fuel according to the demand
of torque and engine rpm. There are also two latest generation three-way pre-catalytic converters ( A-Fig.1) (with two
oxygen sensors for their control) and two post-catalytic converters incorporated inside the silencer ( B-Fig.1).
Page 341 of 1659
4
L714 01 28 00
® Automobili Lamborghini S.p.A. / H S U R F H G X U H H O H L Q I R U P D ] L R Q L S X E E O L F D W H G L V H J X L W R V R Q R V W U H W W D P H Q W H F R Q ¿ G H Q ] L D O L H U L Y R O W H H V F O X V L Y D P H Q W H D O O D 5 H W H ' H D O H U H 6 H U Y L F H 3 R L Q W $ X W R U L ] ] D W L / D P E R U J K L Q L 7 X W W L L G L U L W W L G ¶ D X W R U H V R Q R S U R S U L H W j
G L $ X W R P R E L O L / D P E R U J K L Q L 6 S $ L Q E D V H D O O D O H J J H V X L G L U L W W L G ¶ D X W R U H 7 X W W L L F D S L W R O L 3 ' ) G L F X L V L F R P S R Q J R Q R L P D Q X D O L R I ¿ F L Q D : ( % G H V F U L W W L G L V H J X L W R V L E D V D Q R V X O O H L Q I R U P D ] L R Q L G L V S R Q L E L O L D O
P R P H Q W R G H O O D S X E E O L F D ] L R Q H & R Q U L V H U Y D G L D J J L R U Q D P H Q W R H P R G L ¿ F K H 6 R Q R Y L H W D W H O D U L V W D P S D O D U L S U R G X ] L R Q H O ¶ L Q R O W U R D S H U V R Q H Q R Q D X W R U L ] ] D W H H R D W H U ] H S H U V R Q H O D W U D G X ] L R Q H D Q F K H S D U ] L D O H
V H Q ] D O ¶ D X W R U L ] ] D ] L R Q H V F U L W W D G D S D U W H G L $ X W R P R E L O L / D P E R U J K L Q L 6 S $
5 S P O L P L W L Q J G H Y L F H
In normal operating conditions with operative temperatures TH2O 90°C and Toil 90°C, the limiting device is structured
as follows:
in neutral engine limited to 7800 rpm (3500 rpm only for JP and Korea) st
gear U S P
2 nd
gear 8550 rpm
3 rd
gear 8650 rpm
4 th
gear 8500 rpm
5 th
gear 8500 rpm
6 ty
gear U S P
Reverse gear 6000 rpm
The values stated above are indicative and subject to changes introduced in the Factory.
1 R W H It must however be remembered that when the vehicle is hot, idle speed is 680 rpm and it goes up to 820 rpm with the A/C on.
Control and power limitation strategies
The ECU controls rpm limitation using different maps, depending on the environmental conditions at the time: • with engine cold (Water temperature < 60°C) and with low Toil (Oil temperature < 40°C), the rpm are limited
• with engine hot (Water temperature > ƒ & W K H U S P D U H O L P L W H G
Page 342 of 1659
5
L714 01 28 00
Fig.6
AB
Fig.7
B
B
A
A
® Automobili Lamborghini S.p.A.
/ H S U R F H G X U H H O H L Q I R U P D ] L R Q L S X E E O L F D W H G L V H J X L W R V R Q R V W U H W W D P H Q W H F R Q ¿ G H Q ] L D O L H U L Y R O W H H V F O X V L Y D P H Q W H D O O D 5 H W H ' H D O H U H 6 H U Y L F H 3 R L Q W $ X W R U L ] ] D W L / D P E R U J K L Q L 7 X W W L L G L U L W W L G ¶ D X W R U H V R Q R S U R S U L H W j
G L $ X W R P R E L O L / D P E R U J K L Q L 6 S $ L Q E D V H D O O D O H J J H V X L G L U L W W L G ¶ D X W R U H 7 X W W L L F D S L W R O L 3 ' ) G L F X L V L F R P S R Q J R Q R L P D Q X D O L R I ¿ F L Q D : ( % G H V F U L W W L G L V H J X L W R V L E D V D Q R V X O O H L Q I R U P D ] L R Q L G L V S R Q L E L O L D O
P R P H Q W R G H O O D S X E E O L F D ] L R Q H & R Q U L V H U Y D G L D J J L R U Q D P H Q W R H P R G L ¿ F K H 6 R Q R Y L H W D W H O D U L V W D P S D O D U L S U R G X ] L R Q H O ¶ L Q R O W U R D S H U V R Q H Q R Q D X W R U L ] ] D W H H R D W H U ] H S H U V R Q H O D W U D G X ] L R Q H D Q F K H S D U ] L D O H
V H Q ] D O ¶ D X W R U L ] ] D ] L R Q H V F U L W W D G D S D U W H G L $ X W R P R E L O L / D P E R U J K L Q L 6 S $
Fuel pump
There is only one electric fuel pump (
A-Fig.6) and it is in the right tank. This pump is controlled by an ECU ( B-Fig.6)
which in turn is controlled by the master control unit.
The pump has an operating pressure ranging between 4 and 6 bar, depending on the various operating conditions
of the vehicle.
The pump sends the fuel to the two high pressure pumps (which are mechanical) that compress the fuel and take the pressure to a value varying from 120 to 140 bar, according to vehicle operation.
Both the high and low pressure pumps are monitored by two sensors installed on the respective lines to prevent overpressure problems. Linear phase transformers
Linear phase transformers allow the engine phase to vary according to the torque required in order to always have optimum phasing.
In this version they are always enabled, and the phasing follows different maps according to the load and the atmospheric conditions. Piloting is performed by a solenoid valve ( A-Fig.7), which makes the oil pass inside the phase-changing gear.
This operation is managed by the injection control units that also receive the position of the camshaft through the
Hall effect sensors ( B-Fig.7) mounted on the camshafts:
• two sensors for the exhaust (one per cylinder bank)
• two sensors for the intake (one per cylinder bank)
Page 405 of 1659
1
L714 01 42 00
A
B
C
® Automobili Lamborghini S.p.A.
7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
( * ( $ 5 6 < 6 7 ( 0 System description•
The Selespeed System is a system developed by Magneti Marelli to control a standard mechanic transmission
by operating the clutch Actuator and the command shaft of the conventional gear box.
• The Selespeed System also interfaces with the engine controller in order to adapt the engine torque and speed
during the gear shifting phases.
• 7 K H 6 H O H V S H H G F R P S R Q H Q W V F R Q V W L W X W H D Q D G G R Q N L W W K D W Q R U P D O O \ G R H V Q ¶ W U H T X H V W L P S R U W D Q W P R G L ¿ F D W L R Q V W R
the vehicle/transmission .
• The ³ ( * H D U V \ V W H P ´ constitutes the Selespeed application for mechanical gearboxes.
Layout
A. Valve Group and Gear Actuetor
B. Gearbox
C. Power unit
Page 417 of 1659
13
L714 01 42 00
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
& $ 5 ¶ 6 ) 8 1 & 7 , 2 1 $ / , 7 <
: D N H X S
When the driver door is opened and the car is sleeping starts the Z D N H X Sphase. In this phase the TCU is partially
switched on, and if the hydraulic pressure is lower than a limit the pump is activated for maximum 4 seconds.
& U D Q N L Q J
In the car there’s a relay that releases the cranking. This relay is controlled by E-Gear TCU.
The cranking is only released if the brake is pushed and not paddles an R switch pushed.
The cranking can be done also with a gear engaged. The system will engage the neutral before release the cranking. 3 L F N X S
The pick up is related to the gas pedal position and how it’s pushed.
To perform good pick up is important to keep constant the gas pedal.
During pick up is calculated the clutch wear index, if the engine and clutch temperatures are in a range.
7 R $ Y R L G S L F N X S Z L W K E U D N H S X V K H G W K H V \ V W H P F R Q W U R O V W K H & O X W F K W R U T X H W R D ¿ [ H G Y D O X H ' U L Y D E L O L W \ 0 R G H V • Normal Mode , Sport Mode, Corsa Mode: the gearshifts are performed by the driver, with steering paddles,
better keeping constant the gas pedal. The gearshift speed and comfort quality depend on the gas pedal posi-
tion and engine speed.
• Automatic Mode and Automatic Sport Mode: the gearshift are performed directly from the E-Gear TCU, that
decides when to perform them according to the gas pedal position and vehicle speed.
• Underspeed: in order to avoid engine stalling if the driver doesn’t require any DW, E-Gear TCU perform itself
them when the engine speed becomes too low.
• Overspeed: in order to avoid engine limiter intervention the automatic gearshift is done when the maximum
engine speed is reached. This Function is not available in CORSA Mode.