battery replacement LAND ROVER DISCOVERY 1995 User Guide

ELECTRICAL
15
REPAIR Refit
9.If removed fit the mounting plate to the actuator.
10.Engage the actuator operating rod with hooked
end of the actuator link.
11.Fit the actuator and mounting plate to the door
and loosely secure with the four screws.
12.Set the mounting plate with the screws in the
centre of the slotted holes, then tighten the
screws.
13.Connect the actuator lead to the door harness.
14.Reconnect battery negative lead.
15.With the sill locking button held in position, set
the bellcrank to approximately the position it
would be in if the sill button was depressed to
half of its total movement.
16.At this setting check the electrical operation of
the door lock. Adjust the mounting plate as
necessary to achieve the correct setting. Fully
tighten the securing screws on completion.
17.Refit the vapour barrier.
18.Connect the sill button operating rod to the
bellcrank, hold in position, fit the door trim panel
and the door pull.
BULB REPLACEMENT
For bulb type and rating refer to rating shown on the
bulb or bulb replacement list.
See GENERAL
SPECIFICATION DATA, Information, Bulbs
HEADLIGHT
Service repair no - 86.40.02/13
Remove
1.Rotate three retaining clips 10 degrees, to align
with slots in headlight mounting plate.
2.Withdraw light unit
NOTE: Detach adjustment operating rod
on vehicles fitted with headlight levelling.3.Disconnect electrical multiplugs and remove
headlight unit.
4.Release spring clips and withdraw headlight
bulb.
Key
1. Headlight
2. Retaining clips
3. Bulb
4. Spring clip
5. Cover
6. Bulb sidelight
7. Plug
8. Plug sidelight
Refit
5.Reverse removal procedure.

ELECTRICAL
39
REPAIR CIGAR LIGHTER AND BULB
Service repair no - 86.65.60
Service repair no - 86.45.55
Cigar Lighter
Remove
1.Remove centre console.
See CHASSIS AND
BODY, Repair, Centre Console
2.Depress lugs securing cigar lighter, withdraw
lighter from centre console.
Bulb replacement
3.Remove bulb from holder.
Refit
4.Reverse removal procedure.OIL PRESSURE WARNING SWITCH - V8i
Service repair no - 86.65.30
Remove
1.Disconnect the battery negative lead.
2.Disconnect electrical lead.
3.Unscrew switch unit.
4.Remove switch and sealing washer.
Refit
5.Reverse removal procedure. Using a NEW
sealing washer.

86ELECTRICAL
40
REPAIR INSTRUMENT ILLUMINATION ELECTRONIC
DIMMER/RHEOSTAT
Service repair no - 86.65.07
Electronic dimming control switch is located in
instrument panel finisher. Rotate control to vary
intensity of illumination.
Remove
1.Disconnect the battery negative lead.
2.Remove instrument panel finisher.
See
CHASSIS AND BODY, Repair, Instrument
Panel Finisher
3.Remove 2 screws securing rheostat, remove
rheostat.
Refit
4.Reverse removal procedure.WINDOW LIFT/HEATED SEAT CUSHION
SWITCHES AND BULBS
Service repair no - 86.25.16 - Switches
Service repair no - 86.45.29 - Bulb
Switch Replacement
1.Disconnect the battery negative lead.
2.Carefully release rear of surround from centre
console.
3.Remove screws, pry window lift switch surround
from glove box.
4.Disconnect multi-plug(s) at rear of switch(es).
5.Apply pressure to rear of switch, push it through
surround.
Bulb replacement
6.Identify bulb to be replaced and remove
appropriate switch.
7.Rotate bulb holder 90°and withdraw it from
switch; discard bulb and holder.
Refit
8.Reverse removal procedure.

ELECTRICAL
41
REPAIR COOLANT TEMPERATURE TRANSMITTER - V8i
Service repair no - 26.10.02
Remove
1.Disconnect battery negative lead.
2.Disconnect lead from transmitter.
3.Remove transmitter, discard sealing washer if
fitted.
Refit
4.Coat threads of replacement transmitter with
Loctite 572.
5.Fit a new sealing washer to transmitter.
6.Fit transmitter, connect lead.
7.Top-up cooling system.HEATED FRONT SCREEN
Heated front screen will operate when switch is
operated, with engine running. Timer unit will provide
a preset time cycle of 7« minutes±20%.
To identify timer unit.
See Electrical Trouble
Shooting Manual.Electrical Troubleshooting
Manual
Switching OFF ignition, or further operation of heated
front screen switch during cycle will switch off screen
and cancel, reset and switch off timer unit.