bulb LAND ROVER DISCOVERY 1995 Owner's Guide

ELECTRICAL
43
REPAIR ANTI-THEFT ALARM ECU (96 MODELS)
Service repair no - 86.55.85
Remove
1.Remove 4 studs securing fascia left hand
closing panel.
2.Remove closing panel.
3.Disconnect 2 multiplugs from ECU.
4.Remove nut securing ECU/relay bracket.
5.Lower bracket.
6.Remove 2 nuts securing ECU to bracket.
7.Remove ECU.
NOTE: A new ECU must be initialised
using TestBook.
Refit
8.Reverse removal procedure.HANDSET (96 MODELS)
If vehicle does not respond to handset immediately, it
may have lost synchronisation. To re-synchronise,
press either button, 4 times in quick succession. If
handset still fails to respond, check batteries, refer to
Owner's handbook. If batteries are okay, it may be
necessary to use emergency key access, refer to
Owner's handbook.
NOTE: New handsets must be initialised
using TestBook.
PASSIVE COIL (96 MODELS)
Service repair no - 86.77.35
Remove
1.Remove steering column shroud.
See
STEERING, Repair, Steering column shroud
2.Release multiplug from harness clip and
disconnect.
3.Release passive coil from starter switch.
4.Remove bulb holder/starter switch shroud.
5.Remove coil.
Refit
6.Fit coil, ensuring switch illumination bulb harness
passes through large cut-out.
7.Secure coil with cable tie.
8.Position bulb holder/starter switch shroud and
locate bulb.
9.Locate bulb holder/starter switch shroud,
ensuring cut-out in shroud aligns with lug on
starter switch.
10.Connect multiplug and secure to clip.
11.Fit column shroud.

86ELECTRICAL
44
REPAIR BONNET SWITCH
Service repair no - 86.55.89
Remove
1.Remove 2 bolts securing sounder, move
sounder aside.
2.Locate and disconnect bonnet switch multiplug.
3.Release and remove switch.
Refit
4.Reverse removal procedure.ULTRASONIC SENSOR
Service repair no - 86.77.32
Remove1.Release sensor from switch panel.
2.Disconnect multiplug and remove sensor.
Refit
3.Reverse removal procedure.
ANTI-THEFT ALARM INDICATOR LIGHT (96
MODELS)
Service repair no - 86.45.61
See Instrument illumination and warning light
bulbs
ENGINE IMMOBILISATION WARNING LIGHT (96
MODELS)
Service repair no - 86.45.61
See Instrument illumination and warning light
bulbs

86ELECTRICAL
48
REPAIR STARTER MOTOR HEAT SHIELD - 4.0 V8
Service repair no - 86.60.12
Remove
1.Disconnect battery negative lead.
2.Raise vehicle on ramp.
3.Remove heated oxygen sensor from RH exhaust
front pipe.
See EMISSION CONTROL, Repair,
Heated Oxygen Sensor (HO2S) - 4.0 V8
4.Remove bolt securing heat shield to RH engine
mounting bracket.
5.Release heat shield clip from starter solenoid.
6.Manoeuvre heat shield rearwards and around
starter motor.
Refit
7.Reverse removal procedure.BULB - FRONT FOG LAMP
Service repair no - 86.40.94
Remove
1.Remove front fog lamp.
See fog lamp - front
2.Remove 2 Torx screws securing fog lamp to
bracket and collect 2 spacers.
3.Release fog lamp adjustment ball joint from
bracket and remove lamp.
4.Release lamp lens from shroud.
5.Disconnect 2 Lucars from bulb.
6.Release bulb retaining clip.
7.Remove bulb from lens.

ELECTRICAL
49
REPAIR Refit
8.Fit bulb to lens.
9.Secure bulb retaining clip.
10.Connect 2 Lucars to bulb.
11.Position lamp lens to shroud.
12.Position lamp to bracket and secure fog lamp
adjustment ball joint to bracket.
13.Position spacers, align lamp to bracket and
secure with Torx screws.
14.Fit front fog lamp.
See fog lamp - front; Refit
CLOCK
Service repair no - 88.15.07
Remove
1.Remove drinks tray.
See CHASSIS AND
BODY, Repair, drinks tray
2.Release 4 clock panel securing tags.
3.Release clock panel from louvre panel.
4.Disconnect 2 multiplugs from clock.
5.Remove clock.
Refit
6.Position clock.
7.Connect multiplugs to clock and secure clock to
louvre panel.
8.Fit drinks tray.
See CHASSIS AND BODY,
Repair, drinks tray; Refit
REAR SPEAKER
Service repair no - 88.15.12
Remove
1.Remove 4 screws securing speaker.
2.Release speaker and disconnect 2 Lucars.
3.Remove speaker.
Refit
4.Position speaker, connect Lucars and secure
with screws.