engine oil LAND ROVER DISCOVERY 2002 Repair Manual

ENGINE - TD5
12-1-34 DESCRIPTION AND OPERATION
A tapping towards the right hand side of the cylinder head diverts oil supply from the cast-in groove down to a stub
pipe which attaches to a feed line to the vacuum pump. An hydraulic tensioner is located below the vacuum stub pipe
which receives oil through a small hole in the side of the tensioner body to force a plunger against a plastic faced
adjuster shoe for timing chain tensioning. Oil from the vacuum pump is returned to a port in the timing chain cover via
a short hose which connects to stub pipes at both ends using spring clips.

ENGINE - TD5
ADJUSTMENTS 12-1-35
ADJUST ME NTS
Engine oil pressure check
$% 12.90.09.01
Check
1.Remove oil pressure switch.

+ ENGINE - Td5, REPAIRS, Switch -
oil pressure.
2.Connect pressure check kit LRT-12-052C
adaptor and gauge to oil pressure switch
position on oil cooler.
3.Check and if necessary top up engine oil.
4.Run engine at idle speed and check that oil
pressure is within limits given.

+ GENERAL DATA, Engine - Td5.
5.Switch off ignition.
6.Remove pressure check kit LRT-12-052C.
7.Clean oil spillage.
8.Fit oil pressure switch.

+ ENGINE - Td5, REPAIRS, Switch -
oil pressure.
Adjust
1.If engine oil pressure is outside of specified
limits, check condition of oil pump and/or main
and connecting rod bearings.

ENGINE - TD5
REPAIRS 12-1-37
REPAIRS
Pulley - crankshaft
$% 12.21.01
Remove
1.Remove fixings and underbelly panel.
2.Remove radiator.

+ COOLING SYSTEM - Td5, REPAIRS,
Radiator.
3.Using a 15 mm ring spanner, release the
auxiliary drive belt tensioner.
4.Remove auxiliary drive belt.
5.Remove 3 bolts and remove crankshaft TV
damper.
6.Position tool LRT-51-003 to crankshaft pulley
and secure with 2 bolts.
7.Remove and discard crankshaft pulley bolt.
Remove crankshaft pulley.
8.Remove 2 bolts and remove tool LRT-51-003
Refit
1.Position new crankshaft pulley to vice.
2.Remove 3 bolts and remove TV damper from
new crankshaft pulley.
3.Using a lint free cloth, thoroughly clean oil seal
recess and the running surface on crankshaft
pulley.
4.Fit crankshaft pulley. 5.Fit tool LRT-51-003 to crankshaft pulley and
secure with 2 bolts.
6.Fit new crankshaft pulley bolt and tighten to
460 Nm (340 lbf.ft), using a torque multiplier.
7.Remove 2 bolts and remove tool LRT-51-003
from crankshaft pulley.
8.Fit TV damper to crankshaft pulley and tighten
– TV damper bolts to 80 Nm (59 lbf.ft) .
9.Fit auxiliary drive belt to pulleys.
10.Fit radiator.

+ COOLING SYSTEM - Td5, REPAIRS,
Radiator.
11.Fit underbelly panel and secure with fixings.

ENGINE - TD5
12-1-38 REPAIRS
Seal - crankshaft - rear
$% 12.21.20
Remove
1. Automatic models: Remove drive plate

+ ENGINE - Td5, REPAIRS, Plate -
drive - automatic.
2. Manual models: Remove flywheel.

+ ENGINE - Td5, REPAIRS, Flywheel.
3.Remove sump gasket.

+ ENGINE - Td5, REPAIRS, Gasket -
sump.
4.Remove 5 bolts securing crankshaft oil seal
housing to cylinder block.
5.Remove crankshaft oil seal housing.
Refit
1.Clean interface between crankshaft oil seal
housing and cylinder block.
2.Position seal protector, LRT-12-061 over
crankshaft boss. Fit new seal and remove tool
LRT-12-061 .
CAUTION: Oil seal must be fitted dry.3.Fit crankshaft rear oil seal housing bolts and
using sequence shown, tighten to 9 Nm (7
lbf.ft).
4.Fit new sump gasket.

+ ENGINE - Td5, REPAIRS, Gasket -
sump.
5. Automatic models: Fit drive plate

+ ENGINE - Td5, REPAIRS, Plate -
drive - automatic.
6. Manual models: Fit flywheel.

+ ENGINE - Td5, REPAIRS, Flywheel.

ENGINE - TD5
REPAIRS 12-1-39
Gasket - cylinder head
$% 12.29.02
Remove
Note: The following procedures cover engines
fitted with or without an EGR cooler. The EGR
cooler is bolted to the front of the cylinder head.
1.Remove bonnet.

+ EXTERIOR FITTINGS, REPAIRS,
Bonnet.
2.Release turnbuckles and remove battery cover.
3.Disconnect battery earth lead.
4.Drain cooling system.

+ COOLING SYSTEM - Td5,
ADJUSTMENTS, Drain and refill.
5.Remove camshaft cover gasket.

+ ENGINE - Td5, REPAIRS, Gasket -
cover - camshaft.
6.Remove cooling fan coupling.

+ COOLING SYSTEM - Td5, REPAIRS,
Fan - viscous.
7.Remove 3 bolts and remove exhaust manifold
heat shield. 8.Remove turbocharger oil feed banjo bolt and
discard sealing washers.
9.Remove 3 nuts, release turbocharger from
exhaust manifold, discard gasket and tie
turbocharger aside.
10.Disconnect multiplugs from compressor, MAF
sensor, turbocharger wastegate modulator,
and AAP & IAT sensor.
11.Remove 2 bolts securing engine harness to
camshaft carrier.
12.Disconnect multiplug from EUI's and coolant
temperature sensor.

ENGINE - TD5
12-1-40 REPAIRS
13.Disconnect 4 glow plug connectors.
14.Disconnect MAP sensor multiplug from inlet
manifold.
15.Position engine harness clear of inlet manifold.
16.Disconnect vacuum hose from EGR valve.
17.Release 3 clips and disconnect coolant hoses
from fuel cooler.
18.Disconnect fuel hoses, tank to fuel cooler and
connector block on cylinder head.
CAUTION: Always fit plugs to open
connections to prevent contamination.19.Disconnect fuel hose from connector block on
cylinder head.
20.Disconnect fuel hose from fuel cooler and
secure to connector block on cylinder head.
This is to prevent contamination of the fuel
injection system.
Pre EU3 model shown
21.Loosen clip screw and disconnect air intake
hose from EGR valve.
22.Loosen vacuum pump oil feed pipe union from
cylinder head and discard 'O' ring.
23.Loosen 2 bolts and release alternator support
bracket from cylinder head.
24. Pre EU3 model: Remove bolt securing EGR
valve pipe clamp to cylinder head.
25. EU3 model: Release the clips and disconnect
the coolant hoses from the EGR cooler.
26.Remove nut and bolt securing cylinder head to
timing chain cover.
27.Release clips and disconnect top hose, heater
hose and heater feed hose.
28.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.

ENGINE - TD5
12-1-42 REPAIRS
37.Using suitable lifting chains and tool LRT-12-
138 carefully remove cylinder head and place
on wooden blocks or stands.
CAUTION: Support both ends of cylinder
head on blocks of wood. With the camshaft
carrier bolted down, the injector nozzles
and some of the valves will protrude from
the face of the cylinder head.
38.Remove cylinder head gasket.
39.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of cylinder head.
40.Remove and discard plastic dowels from
cylinder block.Refit
1.Clean mating faces of cylinder head and
cylinder block.
2.Check cylinder head for warping, across centre
and from corner to corner: – Maximum warp =
0.10 mm (0.0004 in)
CAUTION: Cylinder heads may not be
refaced, replace cylinder head if warping
exceeds figure given.
3.Ensure coolant and oil passages are clean.
4.Clean dowel holes and fit new plastic dowels.
5.Lightly lubricate threads and beneath heads of
cylinder head bolts with clean engine oil.
6.Fit new cylinder head gasket of the correct
thickness with the word 'TOP' uppermost.
7.Using assistance, fit cylinder head and locate
onto dowels.
8.Carefully enter cylinder head bolts, DO NOT
DROP. Lightly tighten bolts.
9.Using the sequence shown, progressively
tighten cylinder head bolts to 30 Nm (22 lbf.ft),
then to 65 Nm (48 lbf.ft), then a further 90
°, then
a further 180
° and finally a further 45°.
CAUTION: Ensure correct sequence is
followed for all 5 tightening stages. Do not
tighten bolts 315 degrees in one operation.
10.Fit nut and bolt securing cylinder head to timing
chain cover and tighten to 25 Nm (18 lbf.ft).

ENGINE - TD5
REPAIRS 12-1-43
11.Clean camshaft sprocket and mating face on
camshaft.
12.Ensure engine is set to TDC No. 1 cylinder and
mark on camshaft sprocket is positioned
between the 2 coloured links.
13.Position camshaft sprocket to camshaft; fit and
lightly tighten new bolts, then loosen bolts half
a turn.
14.Clean timing chain fixed guide retaining pin and
apply Loctite 242 to threads.
15.Fit timing chain fixed guide retaining pin and
tighten to 25 Nm (18 lbf.ft) .
16.Clean timing chain tensioner and fit new
sealing washer.
17.Fit timing chain tensioner and tighten to 45 Nm
(22 lbf.ft).
18.Tighten bolts securing camshaft sprocket to
camshaft to 37 Nm (27 lbf.ft).
19.Remove tool LRT-12-058 from camshaft.
20.Remove tool LRT-12-158 from gearbox bell
housing.
21.Fit new camshaft bore blanking plug and 'O'-
ring seal in recess in cylinder head.
22.Clean vacuum pump union.
23.Tighten union securing vacuum pump oil feed
pipe to cylinder head to 10 Nm (7 lbf.ft) .
24.Fit bolts securing alternator support bracket to
cylinder head and tighten to 25 Nm (18 lbf.ft) .
25.Connect top hose and heater hoses and secure
with clips.
26. Pre EU3 model:Fit bolt securing EGR pipe
clamp to cylinder head bolt and tighten to 10
Nm (7 lbf.ft) .
27. EU3 model: Connect coolant hoses to EGR
cooler and secure with the clips.
28.Position air intake hose to EGR valve and
tighten clip screw.
29.Disconnect fuel hose from connector block and
connect to fuel cooler.
30.Connect fuel hoses to fuel cooler and
connector block on cylinder head.
31.Connect coolant hoses to fuel cooler and
secure clips.
32.Connect vacuum hose to EGR valve.
33.Position engine harness and connect multi
plugs and glow plug connectors.
34.Fit and tighten bolts, engine harness to
camshaft carrier.
35.Clean exhaust manifold and turbocharger
interface.
36.Fit new gasket to exhaust manifold, position
turbocharger and tighten – nuts securing
turbocharger to manifold to 30 Nm (22 lbf.ft).
37.Clean turbocharger oil feed hose bolt.
38.Position turbocharger oil feed hose using new
sealing washers. Fit banjo bolt securing
turbocharger oil feed hose and tighten to 25 Nm
(18 lbf.ft) . 39.Position exhaust manifold heatshield and
tighten M6 bolts to 9 Nm (7 lbf.ft) and M8 bolt to
25 Nm (18 lbf.ft).
40.Fit cooling fan coupling.

+ COOLING SYSTEM - Td5, REPAIRS,
Fan - viscous.
41.Fit camshaft cover with new seal.

+ ENGINE - Td5, REPAIRS, Gasket -
cover - camshaft.
42.Refill cooling system.

+ COOLING SYSTEM - Td5,
ADJUSTMENTS, Drain and refill.
43.Connect battery earth lead.
44.Fit battery cover and secure fixings.
45.Fit bonnet.

+ EXTERIOR FITTINGS, REPAIRS,
Bonnet.

ENGINE - TD5
12-1-46 REPAIRS
Gasket - cover - camshaft
$% 12.29.40
Remove
1.Remove 3 bolts and remove engine acoustic
cover.
2.Release clip and disconnect breather hose
from camshaft cover.
3.Remove 13 bolts securing camshaft cover.
4.Collect sealing washers and spacers.
5.Remove camshaft cover and gasket.
Refit
1.Clean camshaft cover and mating face.
2.Renew sealing washers and spacers as
necessary. 3. Not EU3 model:- Apply two 3 mm diameter
beads of sealant, STC 5433, to areas 'A' shown
on illustration.
Excessive use of sealant could result in
blockage of oil drain hole, arrowed 'B' on
illustration.
4.Fit new gasket, fit camshaft cover to camshaft
carrier and tighten – camshaft cover bolts to 9
Nm (7 lbf.ft).
5.Position breather hose to camshaft cover and
secure with clip.
6.Fit engine acoustic cover and secure with
fixings.
M12 7538
A
B
A

ENGINE - TD5
REPAIRS 12-1-47
Engine and ancillaries
$% 12.41.01
Remove
1.Remove bonnet.

+ EXTERIOR FITTINGS, REPAIRS,
Bonnet.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Drain engine oil.

+ MAINTENANCE, PROCEDURES,
Engine oil - diesel engine.
4.Remove radiator.

+ COOLING SYSTEM - Td5, REPAIRS,
Radiator.
5.Remove turbocharger.

+ ENGINE MANAGEMENT SYSTEM -
Td5, REPAIRS, Turbocharger.
6.Release clips and disconnect heater hoses
from fuel cooler and coolant rail.
7.Release clip and disconnect expansion tank
coolant hose from fuel cooler.
8.Disconnect fuel hoses, tank to fuel cooler and
connector block on cylinder head.
CAUTION: Always fit plugs to open
connections to prevent contamination.9.Disconnect fuel hose from fuel cooler and
secure to connector block on cylinder head.
This is to prevent contamination of the fuel
injection system.
10.Release servo vacuum pipe from clip on fuel
cooler and release hose from vacuum pump.
11.Release expansion tank from body mounting,
release clip, disconnect hose and remove tank.