ECO mode LAND ROVER FREELANDER 2001 User Guide

AIR CONDITIONING
82-10REPAIRS
Condenser
$% 82.15.07
Remove
1.Disconnect battery earth lead.
2.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
3. Td4 models: Remove intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
4. Remove bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5. KV6 models: Remove 2 bolts securing PAS
fluid cooler to armature.
6. Up to 04MY: Remove 4 nuts and 4 bolts
securing armature to body, remove armature.
7. 04MY on: Remove 4 bolts securing armature to
crash cans and remove armature.8.If fitted, remove 4 scrivets securing LH and RH
air deflectors, remove both deflectors.
9.Remove 2 bolts securing condenser to radiator.
10.Remove 2 bolts securing receiver drier
mounting brackets to radiator.

M76 4176

AIR CONDITIONING
REPAIRS 82-11
11.Remove 2 bolts securing A/C pipes to
condenser and release pipes from condenser.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
12.Remove and discard 'O' rings from A/C pipes.
13.Remove condenser.
14.Remove 8 screws, securing 4 mounting
brackets to condenser and move aside.
15.Remove and discard receiver drier, plug
connections.Refit
1.Fit condenser mounting brackets, fully tighten
LH screws. Leave RH screws loose until
receiver drier is fitted.
CAUTION: Ensure that bolts of the correct
length are used on refit.
2.Lubricate new 'O' rings with clean refrigerant
oil, fit one seal to each condenser pipe.
3.Position A/C pipes to condenser, fit bolts and
tighten to 8 Nm (6 lbf.ft).
4.Fit bolts securing condenser to radiator and
tighten to 8 Nm (6 lbf.ft).
5.Fit receiver drier assembly to condenser.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
6.Fit air deflectors and secure with scrivets.
7. Up to 04MY: Position armature, fit and tighten
4 nuts and bolts securing armature to body to
25 Nm (18 lbf.ft).
8. 04MY on: Position armature, fit bolts securing
armature to crash cans and tighten to 25 Nm
(18 lbf.ft).
9. KV6 models:Align PAS fluid cooler and tighten
bolts to 8 Nm (6 lbf.ft).
10.Fit bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
11. Td4 models: Fit intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
12.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
13.Connect battery earth lead.
M82 0706

AIR CONDITIONING
82-12REPAIRS
Receiver drier
$% 82.17.03
Remove
1.Disconnect battery earth lead.
2.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
3. Remove bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
4. KV6 models: Remove 2 bolts securing PAS
fluid cooler to armature.
5. Up to 04MY: Remove 4 nuts and 4 bolts
securing armature to body and remove
armature.
6. 04MY on: Remove 4 bolts securing armature to
crash cans and remove armature.
7.If fitted, remove 2 scrivets securing LH air
deflector and remove air deflector.8. Td4 models: Remove intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
9.Remove 4 screws from clamps securing
receiver drier to condenser.
10.Remove receiver drier from condenser.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
11.Discard dust shield and 'O' ring seals.

M76 4176

AIR CONDITIONING
REPAIRS 82-13
Refit
1.Lubricate new 'O' rings, dust shield and
condenser thread with refrigerant oil.
2.Fit 'O' rings and dust shield to receiver drier.
CAUTION: Do not remove receiver/dryer
from packaging until immediately before
installation.
3.Fit receiver drier to condenser and tighten to 12
Nm (9 lbf.ft).
4.Tighten clamps securing receiver drier to
condenser.
5.If fitted, fit air deflector and secure with scrivets.
6. Td4 models: Fit intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
7. Up to 04MY: Position armature, fit and tighten
4 nuts and bolts securing armature to body to
25 Nm (18 lbf.ft).
8. 04MY on: Position armature, fit bolts securing
armature to crash cans and tighten bolts to 25
Nm (18 lbf.ft).
9. KV6 models: Align PAS fluid cooler and
tighten bolts to 8 Nm (6 lbf.ft).
10.Fit bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
11.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
12.Connect battery earth lead.
Switch - control
$% 82.20.07
Remove
1.Remove radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.
2.Remove 3 heater control knobs.
3.Remove 2 screws securing heater control
finisher to heater controls and remove finisher.
4.Disconnect multiplug from A/C control switch.
5.Remove switch from heater controls.
Refit
1.Fit A/C control switch and connect multiplug.
2.Fit heater control finisher and secure with
screws.
3.Fit heater control knobs.
4.Fit radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.

AIR CONDITIONING
82-14REPAIRS
Sensor - refrigerant pressure
$% 82.20.38
Remove
1.Disconnect battery earth lead.
2.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
3. Td4 & KV6 models: Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Release multiplug from refrigerant pressure
sensor.
WARNING: Under no circumstances should
refrigerant hoses be disconnected without
first discharging the system.
5.Remove refrigerant pressure sensor from A/C
pipe mounting. Use two spanners to avoid
straining A/C pipe mounting.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
6.Discard 'O' ring.Refit
1.Clean refrigerant pressure switch and
surrounding area.
2.Fit new 'O' ring to sensor and tighten to 10 Nm
(7.5 lbf.ft).
3.Fit multiplug to sensor.
4. Td4 & KV6 models: Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
6.Connect battery earth lead.

INSTRUMENTS
88-6 REPAIRS
Sender unit - fuel tank gauge
$% 88.25.32
Remove
1.Disconnect battery earth lead.
2.Remove fuel pump assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Pump - fuel.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Pump - integral - fuel tank - rear -
up to 03MY.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
3.Disconnect 2 Lucars from top of pump unit
assembly.
4.Release sprag clip securing sender to pump
unit assembly.
5.Remove sender unit.
Refit
1.Position sender to location slots and engage
sprag clip.
CAUTION: Ensure that each of the 4
location lugs on the sender are engaged
with corresponding slots in the tank unit.
2.Connect Lucars to top of pump unit assembly.
3.Fit fuel pump assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Pump - fuel.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Pump - integral - fuel tank - rear -
up to 03MY.
4.Connect battery earth lead.
Sender unit assembly - fuel tank - Td4
models - from 03MY
$% 88.25.37
Remove
1.Disconnect battery earth lead.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
2.If fuel tank is full, using a fuel recovery
appliance, drain excess fuel from fuel filler neck
until a level below height of fuel pump is
obtained.
3.Open RH rear and tail doors.
4.Fold RH rear seat forward.
5.Remove 3 fasteners securing front and rear
carpets.
6.Pull back carpet from fuel tank sender
assembly access panel.
M88 0356