coolant LAND ROVER FREELANDER 2001 User Guide

TORQUE WRENCH SETTINGS
06-4
Engine – K1.8
TORQUE DESCRIPTION METRIC IMPERIAL
Big end bearing cap dowel bolts:
⇒ Stage 120 Nm 15 lbf.ft
⇒ Stage 2+45°+45°
Bearing ladder to cylinder block bolts:
⇒ Stage 1
†++5 Nm 3.5 lbf.ft
⇒ Stage 2
† ++30 Nm 22 lbf.ft
Camshaft carrier to cylinder head bolts
†++10 Nm 7.5 lbf.ft
Camshaft cover to carrier bolts
†8 Nm 6 lbf.ft
Camshaft gear bolt 65 Nm 48 lbf.ft
Camshaft rear oil seal cover plate bolts:
⇒ Exhaust25 Nm 18 lbf.ft
⇒ Inlet6 Nm 4.5 lbf.ft
Camshaft sensor bolt 8 Nm 6 lbf.ft
Camshaft timing belt lower front cover bolts 9 Nm 7 lbf.ft
Camshaft drive belt upper front cover bolts 5 Nm 3.5 lbf.ft
Camshaft timing belt rear cover bolts 9 Nm 7 lbf.ft
Camshaft timing belt tensioner bolt
* 25 Nm 18 lbf.ft
Camshaft upper cover to rear cover bolts 5 Nm 3.5 lbf.ft
Coolant outlet elbow to cylinder head bolts 9 Nm 7 lbf.ft
Crankshaft pulley bolt 205 Nm 151 lbf.ft
Cylinder head bolts
⇒ Stage 1
†20 Nm 15 lbf.ft
⇒ Stage 2
†+180 °+180 °
⇒ Stage 3
†+180 °+180 °
Dipstick tube to cylinder block 10 Nm 7.5 lbf.ft
Dipstick tube bracket and thermostat housing to cylinder block bolt 10 Nm 7.5 lbf.ft
Engine earth lead to body nut 9 Nm 7 lbf.ft
Engine harness to oil pump housing bolts 10 Nm 7.5 lbf.ft
Engine LH gearbox mounting bracket through bolt 80 Nm 59 lbf.ft
Engine LH mounting bracket to body bolts 45 Nm 33 lbf.ft
Engine lower steady to sump mounting bracket bolt 80 Nm 59 lbf.ft
Engine lower steady bracket to sump bolts 100 Nm 74 lbf.ft
Engine lower steady to subframe bolt 80 Nm 59 lbf.ft
Engine steady to LH mounting bolt 25 Nm 18 lbf.ft
Engine steady (lower) to rear beam bolt 80 Nm 59 lbf.ft
Engine steady (lower) to sump mounting bracket bolt 80 Nm 59 lbf.ft
Engine steady (upper RH) to body bolt 80 Nm 59 lbf.ft
Engine steady (upper RH) to top arm bolt 80 Nm 59 lbf.ft
Engine to gearbox top and front cover plate bolts and nuts 80 Nm 59 lbf.ft
Flywheel to crankshaft bolts
†*80 Nm 59 lbf.ft
Front cover plate to gearbox M6 bolt 9 Nm 7 lbf.ft
Ignition coils to camshaft cover bolts 8 Nm 6 lbf.ft
Oil pick-up strainer bolt 12 Nm 9 lbf.ft
Oil pick-up strainer support bracket to oil rail bolt 12 Nm 9 lbf.ft
Oil pressure switch
+17 Nm 12.5 lbf.ft
Oil pressure relief valve plug
+25 Nm 18 lbf.ft
Oil pump to cylinder block bolts
†*10 Nm 7.5 lbf.ft
Oil rail to bearing ladder nuts
++9 Nm 7 lbf.ft

TORQUE WRENCH SETTINGS
06-8
Emission Control
TORQUE DESCRIPTION METRIC IMPERIAL
Depression limiter valve and filter assembly Allen screws 8 Nm 6 lbf.ft
EGR cooler to mounting bolts 25 Nm 18 lbf.ft
EGR valve Allen screws 10 Nm 7.5 lbf.ft
EGR solenoid valve bolts 10 Nm 7.5 lbf.ft
EGR pipe to lifting bracket and cylinder head bolts 25 Nm 18 lbf.ft
Fuel rails to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger outlet pipe to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger pipe to coolant rail bolts 25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-9
Engine Management System – EDC
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor Torx screw 8 Nm 6 lbf.ft
Crankshaft position (CKP) sensor Allen screw 8 Nm 6 lbf.ft
'E' box cover Allen screws 2 Nm 1.5 lbf.ft
Engine coolant temperature sensor (ECT) 15 Nm 11 lbf.ft
Engine breather pipe to air cleaner housing bolt 6 Nm 4.4 lbf.ft
Mass air flow / inlet air temperature MAF/IAT sensor to air cleaner housing 6 Nm 4.4 lbf.ft
Throttle pedal to stud nuts 25 Nm 18 lbf.ft
Throttle Position (TP) sensor nuts and bolts 10 Nm 7 lbf.ft
TP sensor release lever nut 10 Nm 7 lbf.ft

TORQUE WRENCH SETTINGS
06-10
Engine Management System – MEMS
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor bolt 8 Nm 6 lbf.ft
Crankshaft position sensor (CKP) to housing bolt 8 Nm 6 lbf.ft
'E' box retaining clip nut 9 Nm 7 lbf.ft
Engine coolant temperature (ECT) sensor to housing bolt
*15 Nm 11 lbf.ft
Fuel cut-off (inertia) switch nuts 2 Nm 1.5 lbf.ft
Idle air control (IAC) valve to manifold Torx screws 1.5 Nm 1.1 lbf.ft
Ignition coil and ht lead cover bolts 10 Nm 7.5 lbf.ft
Ignition coil mounting bolts 8 Nm 6 lbf.ft
Spark plugs to cylinder head 27 Nm 20 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 7 Nm 5 lbf.ft
Throttle actuator support bracket to throttle body Torx screws
(vehicles with cruise control only)9 Nm 7 lbf.ft
Throttle position sensor to housing Torx screws 1.5 Nm 1.1 lbf.ft

TORQUE WRENCH SETTINGS
06-11
Engine Management System – Siemens
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor 8 Nm 6 lbf.ft
CMP sensor mounting bracket bolt 8 Nm 6 lbf.ft
Crankshaft position (CKP) sensor bolt 9 Nm 6.5 lbf.ft
Engine Coolant temperature (ECT) sensor 17 Nm 12.5 lbf.ft
'E' box cover Allen screws 2 Nm 1.5 lbf.ft
'E' box mounting nut 9 Nm 7 lbf.ft
Plug top coils to LH inlet manifold nut and bolt 9 Nm 6.5 lbf.ft
Plug top coils to RH camshaft cover bolts 9 Nm 6.5 lbf.ft
Spark plugs25 Nm 18 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 7 Nm 5 lbf.ft
Throttle pedal assembly to bulkhead nuts 25 Nm 18 lbf.ft
Throttle position (TP) sensor screws 1.5 Nm 1.1 lbf.ft

TORQUE WRENCH SETTINGS
06-14
Cooling System – Td4
Cooling System – K1.8
Cooling System – KV6
†Tighten in sequence.
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant hose adaptor to cylinder head bolts 8 Nm 6 lbf.ft
Coolant rail (lower) to sump bolts 10 Nm 7.5 lbf.ft
Coolant rail to cylinder head bolt 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolt 20 Nm 15 lbf.ft
Coolant pump to cylinder block bolts 10 Nm 7.5 lbf.ft
Fan and motor assembly to fan cowl bolts 5 Nm 4 lbf.ft
Fan cowl to radiator bolts 5 Nm 4 lbf.ft
Fuel cooler to mounting nuts 10 Nm 7.5 lbf.ft
Fuel rail to coolant rail bolt 10 Nm 7.5 lbf.ft
Heatshield to coolant rail Allen screws 8 Nm 6 lbf.ft
Thermostat housing to coolant pump bolts 8 Nm 6 lbf.ft
Upper coolant rail to thermostat housing bolt 8 Nm 6 lbf.ft
TORQUE DESCRIPTION METRIC IMPERIAL
Condenser to radiator bolts 3 Nm 2.2 lbf.ft
Cooling fan control unit mounting bolt 5 Nm 4 lbf.ft
Cooling fan cowl to radiator 5 Nm 4 lbf.ft
Cooling fan and motor assembly to cowl bolts 5 Nm 4 lbf.ft
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant pump to cylinder block bolts
†9 Nm 6.5 lbf.ft
Cooling fan and motor assembly to fan cowl bolts 5 Nm 3.7 lbf.ft
Cooling fan cowl to radiator bolts 5 Nm 3.7 lbf.ft
Cylinder block drain plug
+20 Nm 15 lbf.ft
Injector protection cover to RH fuel rail and inlet manifold bolts 9 Nm 6.5 lbf.ft
Radiator baffle bolts 5 Nm 3.7 lbf.ft
Thermostat housing flange / coolant elbow bolt 18 Nm 13 lbf.ft

TORQUE WRENCH SETTINGS
06-15
Manifolds and Exhaust System – Td4
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant rail to cylinder head bolt 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolt 20 Nm 15 lbf.ft
Coolant rail to thermostat housing bolt 8 Nm 6 lbf.ft
EGR cooler to cylinder head and lifting bracket bolts 25 Nm 18 lbf.ft
EGR pipe clamp screw 10 Nm 7.5 lbf.ft
EGR pipe to cylinder head bolt 20 Nm 15 lbf.ft
EGR pipe to manifold Torx screws 22 Nm 16 lbf.ft
Exhaust manifold to cylinder head nuts 24 Nm 18 lbf.ft
Front pipe clamping plate nuts 50 Nm 37 lbf.ft
Front pipe to intermediate pipe flange nuts 60 Nm 44 lbf.ft
Fuel rail to coolant rail bolt 10 Nm 7.5 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Heat shield to coolant rail Allen screws 8 Nm 6 lbf.ft
Inlet manifold:
⇒ M6 bolts10 Nm 7.5 lbf.ft
⇒ M7 bolts and nuts 15 Nm 11 lbf.ft
Intermediate pipe to tail pipe flange nuts 60 Nm 44 lbf.ft
Tail pipe clamp nut 55 Nm 41 lbf.ft
Turbocharger to exhaust manifold bolts 50 Nm 37 lbf.ft
Turbocharger outlet pipe bolts:
⇒6 mm10 Nm 7.5 lbf.ft
⇒8 mm25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-17
Manifolds and Exhaust Systems – KV6
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant/breather hose bracket to inlet manifold bolt 9 Nm 6.5 lbf.ft
Exhaust heatshield to exhaust mounting bracket bolts 45 Nm 33 lbf.ft
Exhaust heatshield to IRD housing nut 45 Nm 33 lbf.ft
Exhaust heatshield to lower engine steady mounting bracket bolts 9 Nm 6.5 lbf.ft
Exhaust heatshield to pinion housing nuts 25 Nm 18 lbf.ft
Exhaust flange (LH) to front pipe nuts 50 Nm 37 lbf.ft
Exhaust flange (LH) to front pipe nuts 50 Nm 37 lbf.ft
Exhaust manifold to cylinder head nuts 45 Nm 33 lbf.ft
Exhaust front pipe to manifold flange nuts 50 Nm 37 lbf.ft
Heated Oxygen (HO
2S) sensor 55 Nm 41 lbf.ft
Inlet manifold chamber to inlet manifold bolts 18 Nm 13 lbf.ft
Inlet manifold chamber support brackets to RH camshaft cover bolts 10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts and bolts 25 Nm 18 lbf.ft
Intermediate pipe to front pipe nuts 50 Nm 37 lbf.ft
Intermediate pipe to front pipe nuts 50 Nm 44 lbf.ft
Lower engine steady to subframe bolt 100 Nm 74 lbf.ft
Lower engine steady to sump mounting bolt 100 Nm 74 lbf.ft
RH upper engine steady to body bolt 100 Nm 74 lbf.ft
RH upper engine steady to top arm bolt 100 Nm 74 lbf.ft
Tail pipe clamp nuts 55 Nm 41 lbf.ft

TORQUE WRENCH SETTINGS
06-25
Steering
* Tighten with weight of vehicle on suspension
TORQUE DESCRIPTION METRIC IMPERIAL
Ball joint to steering arm nuts 55 Nm 41 lbf.ft
Coolant rail to cylinder block bolts (KV6) 9 Nm 7 lbf.ft
Gear change linkage to bulkhead bolts (Td4 manual) 25 Nm 18 lbf.ft
Heatshield nuts (KV6) 25 Nm 18 lbf.ft
Interlock cable to column lock union (JATCO) 4 Nm 3 lbf.ft
IRD hose clip bolt (Td4) 25 Nm 18 lbf.ft
Key cable clamp bolt (JATCO) 6 Nm 4.5 lbf.ft
PAS pipe clip to engine lifting eye bolt 10 Nm 7.5 lbf.ft
PAS high pressure pipe clip bolt 8 Nm 6 lbf.ft
PAS fluid pipe bracket bolts 10 Nm 7.5 lbf. ft
PAS outlet hose to pump banjo bolt (KV6 & K1.8) 20 Nm 15 lbf.ft
PAS outlet hose to pump banjo bolt (Td4) 25 Nm 18 lbf.ft
PAS outlet pipe clip bolt 22 Nm 16 lbf.ft
PAS pipe to clamp bolt 22 Nm 16 lbf. ft
PAS pipe to engine front mounting plate bolt (KV6) 25 Nm 18 lbf.ft
PAS pipe support bracket to RH hydramount nut (KV6) 85 Nm 63 lbf.ft
PAS pipe to RH turret clip bolt 10 Nm 7.5 lbf.ft
PAS pump high pressure pipe union 25 Nm 18 lbf.ft
PAS pump pulley bolts 10 Nm 7.5 lbf.ft
PAS pump to mounting bracket bolts (KV6 & K1.8) 25 Nm 18 lbf.ft
PAS pump to mounting bracket bolts (Td4):
⇒ M610 Nm 7.5 lbf.ft
⇒ M825 Nm 18 lbf.ft
PAS pump mounting to cylinder block bolts 45 Nm 33 lbf.ft
PAS rack fluid feed pipe union nut 18 Nm 13 lbf. ft
PAS rack fluid return pipe union nut 22 Nm 16 lbf. ft
PAS rack mounting and clamp to bulkhead bolts 45 Nm 33 lbf. ft
Ram feed pipe union nuts:
⇒ Small (6mm) diameter 18 Nm 13 lbf.ft
⇒ Large (10 mm) diameter 24 Nm 18 lbf.ft
Steering column height adjuster clamp bolt and nut 10 Nm 7.5 lbf.ft
Steering column height adjuster clamp bolt and nut 12 Nm 9 lbf.ft
Steering column bracket side support bolt 10 Nm 7.5 lbf.ft
Steering column lock bolt SHEAR
Steering column to fascia support rail (Nyloc) nuts and bolts 14 Nm 10 lbf.ft
Steering column to PAS rack pinion clamp pinch bolt
132 Nm 24 lbf. ft
Steering wheel nut 45 Nm 33 lbf.ft
Track-rod ends to steering arm nuts 55 Nm 41 lbf.ft
Track-rod end pinch bolt * 28 Nm 21 lbf.ft
Track-rod to rack bolts 100 Nm 74 lbf.ft
Turnbuckle lock nuts 90 Nm 66 lbf.ft

TORQUE WRENCH SETTINGS
06-28
Brakes
1 Use NEW bolts
TORQUE DESCRIPTION METRIC IMPERIAL
ABS ECU pipe unions 17 Nm 12 lbf.ft
ABS modulator to mounting bracket bolts 9 Nm 7 lbf.ft
ABS modulator mounting bracket to inner wing:
⇒ Nuts
⇒ Bolts13 Nm
8 Nm10 lbf.ft
6 lbf.ft
Bleed screw - front calipers 10 Nm 7.5 lbf.ft
Brake servo to bulkhead nuts 22 Nm 16 lbf.ft
EGR cooler to mounting bolts 25 Nm 18 lbf.ft
EGR pipe support bracket to engine lifting bracket bolts 25 Nm 18 lbf.ft
Front caliper brake hose banjo bolt 28 Nm 21 lbf.ft
Front caliper guide pin bolts 27 Nm 20 lbf.ft
Front caliper mounting bolts 100 Nm 74 lbf.ft
Front disc shield to hub screw 8.5 Nm 6.3 lbf.ft
Front disc to drive flange screws 5 Nm 3.7 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Handbrake cable to body and subframe bolts 22 Nm 16 lbf.ft
Handbrake cable retaining plate bolts 22 Nm 16 lbf.ft
Handbrake lever assembly to body bolts 22 Nm 16 lbf.ft
Hill Descent Control (HDC) switch bolt 5 Nm 3.5 lbf.ft
Master cylinder to servo nuts 25 Nm 18 lbf.ft
PAS oil cooler pipe bolts 10 Nm 7.5 lbf.ft
Primary and secondary brake pipe union nuts 17 Nm 12 lbf.ft
Rear wheel cylinder pipe union nut 17 Nm 12 lbf.ft
Rear wheel cylinder to backplate bolts 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 6 Nm 4.5 lbf.ft
Road wheel nuts 115 Nm 85 lbf.ft
Turbocharger intercooler pipe to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger pipe to coolant rail bolt 25 Nm 18 lbf.ft
Vacuum pump bolts
122 Nm 16 lbf.ft
Vacuum reservoir to mounting bracket nut 10 Nm 7.5 lbf.ft