ABS LEXUS ES300 2005 Repair Manual

01-8- INTRODUCTIONTERMS FOR AUTOMATIC TRANSAXLE REPAIR
MANUAL
8 Author
: Date
:
U151E, U151F A/T REPAIR MANUAL (RM1021U) ISC
Idle Speed Control-
KSKnock SensorKnock Sensor
MAFMass Air FlowAir Flow Meter
MAPManifold Absolute PressureManifold Pressure
Intake Vacuum
MCMixture Control
Electric Bleed Air Control Valve (EBCV)
Mixture Control Valve (MCV)
Electric Air Control Valve (EACV)
MDPManifold Differential Pressure-
MFIMultiport Fuel InjectionElectronic Fuel Injection (EFI)
MILMalfunction Indicator LampCheck Engine Light
MSTManifold Surface temperature-
MVZManifold Vacuum Zone-
NVRAMNon-V olatile Random Access Memory-
O2SOxygen SensorOxygen Sensor, O2 Sensor (O2S)
OBDOn-Board DiagnosticOn-Board Diagnostic (OBD)
OCOxidation Catalytic ConverterOxidation Catalyst Converter (OC), CC0
OPOpen LoopOpen Loop
PAIRPulsed Secondary Air InjectionAir Suction (AS)
PCMPowertrain Control Module-
PNPPark/Neutral Position-
PROMProgrammable Read Only Memory-
PSPPower Steering Pressure-
PTOXPeriodic Trap OxidizerDiesel Particulate Filter (DPF)
Diesel Particulate Trap (DPT)
RAMRandom Access MemoryRandom Access Memory (RAM)
RMRelay Module-
ROMRead Only MemoryRead Only Memory (ROM)
RPMEngine SpeedEngine Speed
SCSuperchargerSupercharger
SCBSupercharger Bypass-
SFISequential Multiport Fuel InjectionElectronic Fuel Injection (EFI), Sequential Injection
SPLSmoke Puff Limiter-
SRIService Reminder Indicator-
SRTSystem Readiness Test-
STScan Tool-
TBThrottle BodyThrottle Body
TBIThrottle Body Fuel InjectionSingle Point Injection
Central Fuel Injection (Ci)
TCTurbochargerTurbocharger
TCCTorque Converter ClutchTorque Converter
TCMTransmission Control ModuleTransmission ECU (Electronic Control Unit)
TPThrottle PositionThrottle Position
TRTransmission Range-
TVVThermal Vacuum ValveBimetallic Vacuum Switching Valve (BVSV)
Thermostatic Vacuum Switching Valve (TVSV)
TWCThree-W ay Catalytic ConverterThree-W ay Catalytic (TWC)
CC
RO
TWC+OCThree-W ay + Oxidation Catalytic ConverterCCR + CCO
VA FVolume Air FlowAir Flow Meter
VRVoltage RegulatorVoltage Regulator
VSSVehicle Speed SensorVehicle Speed Sensor (Read Switch Type)
WOTWide Open ThrottleFull Throttle

D25834
SST 40-30
- AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL OIL SEAL (U151E)
2545 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
9. INSTALL TRANSAXLE HOUSING OIL SEAL
(a) Using SST and a hammer, drive in a new oil seal.
SST 09223-15020, 09950-70010 (09951-07150)
Oil seal drive in depth:
0
0.5 mm (0
0.020 in.)
(b) Coat the lip of the oil seal with MP grease.
10. INSTALL FRONT DRIVE SHAFT ASSY LH (SEE PAGE 30-8)
11. INSTALL FRONT DRIVE SHAFT ASSY RH (SEE PAGE 30-8)
12. INSTALL FRONT WHEELS
13. ADD AUTOMATIC TRANSAXLE FLUID
14. INSPECT AUTOMATIC TRANSAXLE FLUID (SEE PAGE 40-1)
15. CHECK ABS SPEED SENSOR SIGNAL
w/ VSC (SEE PAGE 05-471)
w/o VSC (SEE PAGE 05-420 )

3203N-09
F41016
F41018F41017
C84803
32-54
- BRAKESPEED SENSOR FRONT LH
2488 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
SPEED SENSOR FRONT LH
REPLACEMENT
HINT:
Replace the RH side by the same procedures with LH side.
1. REMOVE FRONT WHEEL
2. REMOVE FRONT FENDER LINER LH
3. REMOVE SPEED SENSOR FRONT LH
(a) Disconnect the speed sensor connector and clamp.
(b) Remove the 2 clamp bolts holding the sensor harness
and clamp from the body and shock absorber.
(c) Remove the bolt and speed sensor FR LH.
NOTICE:
Do not stick and foreign matter on the sensor tip.

C84803
F41018F41017
A
B
F41016
- BRAKESPEED SENSOR FRONT LH
32-55
2489 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
4. INSTALL SPEED SENSOR FRONT LH
(a) Install the speed sensor FR LH with the bolt.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
NOTICE:
Make sure the sensor tip is clean.
(b) Install the sensor harness clamps with the 2 bolts ºAº and
ºBº to the body and shock absorber.
Torque:
Bolt A: 5.0 NVm (51 kgfVcm, 44 in.Vlbf)
Bolt B: 18.8 NVm (192 kgfVcm, 14 ftVlbf)
(c) Connect the clamp to the knuckle.
(d) Connect the speed sensor connector and clamp.
5. INSTALL FRONT FENDER LINER LH
6. INSTALL FRONT WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
7. CHECK ABS SPEED SENSOR SIGNAL (SEE PAGE 05-420 or 05-471)

C83035
32-58
- BRAKESKID CONTROL SENSOR
2492 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
8. INSTALL REAR AXLE HUB & BEARING ASSY LH
(a) Install the rear axle hub & bearing assy with the 4 bolts.
Torque: 80 NVm (816 kgfVcm, 59 ftVlbf)
9. INSTALL REAR DISC
10. INSTALL REAR DISC BRAKE CALIPER ASSY LH (SEE PAGE 32-41)
11. CONNECT SKID CONTROL SENSOR WIRE
12. INSTALL REAR WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
13. INSPECT TIRE (SEE PAGE 28-1)
14. MEASURE VEHICLE HEIGHT (SEE PAGE 27-3)
15. INSPECT SIDE SLIP (SEE PAGE 27-3)
16. INSPECT CAMBER (SEE PAGE 27-3)
17. INSPECT TOE-IN (SEE PAGE 27-3)
18. ADJUST CAMBER AND TOE-IN (SEE PAGE 27-3)
19. CHECK ABS SPEED SENSOR SIGNAL (SEE PAGE 05-420 or 05-471)

3001U-13
- DRIVE SHAFT / PROPELLER SHAFTDRIVE SHAFT, PROPELLER SHAFT, AXLE (From July,
2003)30-1
2404 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
DRIVE SHAFT, PROPELLER SHAFT, AXLE (From July, 2003)
PROBLEM SYMPTOMS TABLE
Use the table below to help determine the cause of the problem. The numbers indicate the priority of the
possible cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspected AreaSee page
Wander
1. Wheel alignment
2. Steering linkage (Loosen or worn)
3. Hub bearing (Worn)
4. Stabilizer bar26-5
27-3
-
30-2
26-17
27-18
Front wheel shimmy
1. Wheel balance
2. Shock absorber
3. Ball joint (Worn)
4. Hub bearing (Worn)28-1
26-8
27-4
26-16
30-2
Noise1. Inboard joint or outboard joint (Worn)30-8

G29148
NVm (kgfVcm, ftVlbf): Specified torque

Non-reusable partShock Absorber Assy Front LH
Tie Rod Assy LH
Speed Sensor Front LH
Front Suspension Arm
Sub-assy Lower No.1 LH

Cotter Pin Front Axle LH
Hub Bolt
Steering Knuckle LH
Lower Ball Joint Assy LHFront Axle Assy LH Front Drive Shaft Assy LH
210 (2,141, 155)
8.0 (82, 71 in.Vlbf)
Front Disc
107 (1,090, 79)
75 (765, 55)49 (500, 36)294 (2,998, 217)
Front Axle Hub LH
Hole Snap Ring

Cotter Pin

Front Axle Hub
LH Bearing

123 (1,254, 91)
Disc Brake Dust
Cover Front LH
Front Axle Hub Sub-assy LH
8.3 (85, 73 in.Vlbf)
8.3 (85, 73 in.Vlbf)




Front Wheel Bearing
Dust Deflector No.1 LH
Front Disc brake
caliper assy LH
30-6- DRIVE SHAFT / PROPELLER SHAFTDRIVE SHAFT, PROPELLER SHAFT, AXLE (From July,
2003)
2409 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

C91585
NVm (kgfVcm, ftVlbf): Specified torque

Non-reusable partShock Absorber Assy Rear LH
Rear Suspension Arm
Assy No.2 LH
Rear Disc Brake
Caliper Assy LH Rear Axle Carrier
Sub-assy LH
Parking Brake Assy
Rear Axle Hub &
Bearing Assy LHRear Disc Strut Rod Assy Rear
100 (1,020, 74)
62 (630, 46)
100 (1,020, 74)
113 (1,152, 83)
113 (1,152, 83)
5.4 (55, 48 in.Vlbf)
5.4 (55, 48 in.Vlbf)
Rear Axle LH Hub Bolt
80 (816, 59)
X5


255 (2,600, 188)
19 (192, 14)
62 (630, 46)
80 (816, 59)
Rear Suspension Arm
Assy No.1 LH
- DRIVE SHAFT / PROPELLER SHAFTDRIVE SHAFT, PROPELLER SHAFT, AXLE (From July,
2003)30-7
2410 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

300M5-01
C91611
SST
F40136
C83022
F40147
30-8
- DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (From July, 2003)
2411 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
FRONT DRIVE SHAFT (From July, 2003)
OVERHAUL
HINT:

COMPONENTS: See page 30-4

Overhaul the RH side following the same procedures as for the LH side.
1. DRAIN AUTOMATIC TRANSAXLE FLUID
2. REMOVE FRONT WHEEL
3. REMOVE FRONT AXLE HUB LH NUT
(a) Using SST and a hammer, unstake the staked part of the
front axle hub LH nut.
SST 09930-00010
NOTICE:
Loosen the staked part of the lock nut completely, other-
wise the screw of the drive shaft may be damaged.
(b) While applying the brake, remove the front axle hub LH
nut.
4. DISCONNECT FRONT STABILIZER LINK ASSY LH
(a) Remove the nut, and separate the stabilizer link assy LH.
HINT:
If the ball joint turns together with the nut, use a hexagon
wrench (6 mm) to hold the stud.
5. DISCONNECT SPEED SENSOR FRONT LH
(a) Remove the bolt and clip, and separate the sensor wire
and hose from the shock absorber.
NOTICE:
Be careful not to damage the speed sensor.
(b) Remove the bolt, and separate the speed sensor front LH
from the steering knuckle.
NOTICE:
Prevent foreign matter from adhering to the speed sensor.

C92143
SST
C91598
C67412
F07391
30-10
- DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (From July, 2003)
2413 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
11. FIX FRONT AXLE ASSY LH
SST 09608-16042 (09608-02021, 09608-02041)
NOTICE:
The hub bearing could be damaged if it is subjected to the
vehicle's full weight, such as when moving the vehicle with
the drive shaft removed.
Therefore, if it is absolutely necessary to place the vehicle
weight on the hub bearing, first support it with SST.
12. INSPECT FRONT DRIVE SHAFT ASSY LH
NOTICE:
Move the drive shaft assy keeping it level.
(a) Check that there is no remarkable play in the radial direc-
tion of the outboard joint.
(b) Check that the inboard joint slides smoothly in the thrust
direction.
(c) Check that there is no remarkable play in the radial direc-
tion of the inboard joint.
(d) Check the boots for damage.
13. REMOVE FRONT AXLE INBOARD JOINT BOOT
CLAMP
(a) One touch type
(1) Using a screwdriver, remove the front axle inboard
joint boot LH clamp and front axle inboard joint boot
LH No.2 clamp, as shown in the illustration.
(b) Claw Engagement type
(1) Using pliers, remove the front axle inboard joint
boot LH clamp and front axle inboard joint boot LH
No.2 clamp, as shown in the illustration.
14. DISCONNECT FR AXLE INBOARD JOINT BOOT
(a) Separate the inboard joint boot from the inboard joint assy.