LEXUS GS400 2000 Service Repair Manual
Page 741 of 1111
PP0O1±02
PP±92
± PREPARATIONBODY ELECTRICAL
144 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
RECOMMENDED TOOLS
09041±00030Torx Driver T30 .For removing and installing
steering wheel pad
09042±00010Torx Socket T30 .For removing and installing
steering wheel pad
09082±00040TOYOTA Electrical Tester.
Page 742 of 1111
PP0O2±02
± PREPARATIONBODY ELECTRICAL
PP±93
145 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerEngine coolant temperature sender gauge, Engine oil level warn-
ing switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Defogger switch
Bulb (3.4 W)Fuel sender gauge, Engine coolant temperature receiver gauge,
Seat belt warning relay
Dry cell batteryFuel sender gauge, Power mirror
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
Torque wrench
Clip removerFor removing cowl louver
Masking tapeRear window defogger wire
Tin foilRear window defogger wire
Page 743 of 1111
PP0T6±01
PP±94
± PREPARATIONBODY ELECTRICAL
146 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
SSM (Special Service Materials)
08888±88888DuPont Paste No. 4817 or
equivalentRear window defogger
Page 744 of 1111
PP0T8±01
± PREPARATIONBODY
PP±95
147 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BODY
SST (Special Service Tools)
09812±00010Door Hinge Set Bolt Wrench
09806±30010Windshield Moulding Remover
09082±00700SRS Airbag Deployment Tool
09082±00740Airbag Deployment Wire
Sub±harness No.2
Page 745 of 1111
PP0T9±01
PP±96
± PREPARATIONBODY
148 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
RECOMMENDED TOOLS
09070±20010Moulding Remover .
09050±20010Air Riveter.
(09050±02010)Dust Cap.
(09050±02040)Nose Piece No.3.
Page 746 of 1111
PP0TA±01
± PREPARATIONBODY
PP±97
149 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
EQUIPMENT
Clip remover
Torque wrench
Hexagon wrench (6 mm)
Torx driver
Hog ring pliers
Drill
Hand riveter
TapeTo avoid surface damage
Adhesive tapeTo avoid surface damage
Double±stick tape
Adhesive
Cleaner
Shop rag
Knife
Sealer gun
Brush
Putty spatula
Wooden block or similar objectFor tying both piano wire ends
Plastic sheetTo avoid surface damage
Rope (no projections, difficult to break)Seat belt pretensioner disposal
Tire Width: 185 mm (7.28 in.)
Inner diam: 360 mm (14.17 in.)Seat belt pretensioner disposal
Tire with disc wheel Width: 185mm (7.28 in.)
Inner diam 360 mm (14.17 in.)Seat belt pretensioner disposal
Vinyl bagSeat belt pretensioner disposal
Page 747 of 1111
PP0TB±01
PP±98
± PREPARATIONBODY
150 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
LUBRICANT
ItemCapacityClassification
MP grease±±
Page 748 of 1111
PP0TC±01
± PREPARATIONBODY
PP±99
151 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
SSM (Special Service Materials)
08833±00070Adhesive 1324,
THREE BOND 1324 or equivalent
08833±00030Three cement black or equivalent
08850±00801Windshield Glass Adhesive Set
or equivalent
Page 749 of 1111
PR02W±04
± PROPELLER SHAFTTROUBLESHOOTING
PR±1
1988 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
SymptomSuspect AreaSee page
Noise
2. Center bearing (Worn)
3. Flexible rubber coupling (Worn)
4. Spider bearing (Worn or stuck)PR±6
PR±6
PR±7
Vibration
1. Transmission extension housing rear bushing (Worn)
2. Flexible coupling (Worn)
3. Propeller shaft (Runout)
4. Propeller shaft (Imbalance)±
PR±6
PR±7
±
Page 750 of 1111
PR031±01
Q06898Centering Bushing
F02413
F02412
Matchmarks
R07096Phasemarks120°
Q07033
12.5 ± 1 mm
(0.492 ± 0.04 in.) PR±10
± PROPELLER SHAFTPROPELLER SHAFT ASSEMBLY
1997 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL PROPELLER SHAFT
(a) Apply grease to the flexible coupling centering bushings.
Grease:
Molybdenum disulphide lithium base, NLGI No.2
(b) Install the propeller shaft from the vehicle's rear and con-
nect the transmission and differential.
NOTICE:
Support the center support bearing by hand so that the
transmission and intermediate shaft, and propeller shaft
and differential, remain in a straight line.
(c) Temporarily install the 2 center support bearing set bolts
with the adjusting washers.
HINT:
Use the adjusting washers which were removed.
(d) Align the matchmarks and connect the propeller shaft to
the transmission/differential.
(e) Install and torque the 3 bolts, washers and nuts.
NOTICE:
The bolts should be installed from the propeller shaft side.
Torque: 79 N´m (805 kgf´cm, 58 ft´lbf)
(f) If using a new propeller shaft (w/ Phasemarks):
Install the propeller shaft phasemarks and differential/
transmission phasemarks so that their respective align-
ment phasemarks match.
If the propeller shaft phasemarks and differential/trans -
mission phasemarks do not align, install the propeller
shaft and differential alignment phasemarks as close to-
gether as possible.
(g) If using a new propeller shaft (w/o Phasemarks):
Install the propeller shaft.
(h) Torque the 2 center support bearing set bolts.
Torque: 37 N´m (375 kgf´cm, 27 ft´lbf)
HINT:
Adjust the center support bearing to keep the intervals as
shown with the vehicle in the unladen condition.
Under the same condition, check if the center line of the center
support bearing is at right angles to the shaft axial direction.