Lexus IS250 2009 Navigation Manual

Finish
OTHER FUNCTIONS
130
FCC ID: HYQBT0501A
IC ID: 1551A−BT0501A
MADE IN JAPAN
This device complies with Part 15 of the
FCC Rules and RSS −210 Rules. Op-
eration is subject to the following two
conditions: (1) this device may not
cause harmful interference, and (2) this
device must accept any interference re-
ceived, including interference that may
cause undesired operation.
CAUTION
Changes or modifications not ex-
pressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.
CAUTION: Radio Frequency Radi-
ation Exposure
This equipment complies with FCC
radiation exposure limits set forth for
uncontrolled equipment and meets the
FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65.
This equipment has very low levels of
RF energy that it deemed to comply
without maximum permissive expo-
sure evaluation (MPE). But it is desir-
able that it should be installed and op-
erated with at least 20 cm and more be-
tween the radiator and person’s body
(excluding extremities: hands, wrists,
feet and legs).
Co− location: This transmitter must
not be co− located or operated in con-
junction with any other antenna or
transmitter. To use the hands−
free system, you
need to enter your phone into the sys-
tem. Once you have registered it, you
can make a hands− free call.
1. Push the “INFO” button.
2. Touch “Telephone” to display “Tele-
phone” screen.
You can also push
of the steering
wheel to display this screen when the ve-
hicle is stopped.
3. Touch “Settings” to display “Set-
tings” screen.
IS F/350/250_Navi_U
(L/O 0808)
— Enter a Bluetooth rphone

Finish
OTHER FUNCTIONS
131
4. Touch “Bluetooth
” to display the
“Bluetooth
Settings” screen.
5. Touch “Register” to connect your
cellular phone to the system.

: Bluetooth is a registered trademark of Bluetooth SIG. Inc.
6. When this screen is displayed, input
the Passkey displayed on the screen
into the phone.
For the operation of the phone, see the
manual that comes with your cellular
phone.
If you want to cancel it, touch “Cancel”.
7. When the connection is completed,
this screen is displayed.
You do not need to enter the phone in case
of using the same one.
IS F/350/250_Navi_U
(L/O 0808)

Finish
OTHER FUNCTIONS
132
When this screen is displayed, follow the
guidance on the screen to try again.
DConnecting a Bluetoothrphone
AUTOMATICALLY
When you register your phone, auto
connection will be turned on. Always
set it to this mode and leave the
Bluetooth rphone in a condition where
connection can be established.
Each time you touch “Auto Connect”,
auto connection will be switched on or off.
When the “ENGINE START STOP”
switch is in ACCESSORY or IGNITION
ON mode, the selected Bluetooth r
phone will be automatically connected
and the connection result is displayed.
This screen appears when the Bluetooth r
phone is first connected after the “ENGINE
START STOP” switch is in ACCESSORY
or IGNITION ON mode.
IS F/350/250_Navi_U
(L/O 0808)

Finish
OTHER FUNCTIONS
133
MANUALLY
When the auto connection failed or
turned off, you have to connect
Bluetoothrmanually.
Touch “Connect” after having enabled
the Bluetooth rconnection on the
phone.
When the connection is completed, this
screen is displayed.
Now you can use the Bluetooth rphone.
DReconnecting the Bluetooth rphone
If the Bluetooth rphone is discon-
nected with a poor reception from the
Bluetooth rnetwork when the “ENGINE
START STOP” switch is in ACCESSO-
RY or IGNITION ON mode, the system
automatically reconnects the Blue-
tooth rphone. In this case, the connec-
tion result is not displayed.
If the Bluetooth ris disconnected on pur-
pose such as you turned your cellular
phone off, this does not happen. Recon-
nect it by the following methods.
DSelect the Bluetooth rphone again.
DEnter the Bluetooth rphone.
IS F/350/250_Navi_U
(L/O 0808)

Finish
OTHER FUNCTIONS
134
After you enter the Bluetoothrphone,
you can call by using hands− free sys-
tem. You can call using the 7 methods
described below.
DBy dial
You can call by inputting the telephone
number.
This cannot be operated while driving.
Touch the desired key to input the tele-
phone number.
Each time you touch A, an inputted digit is
deleted.
When you touch
, the number you
called last is inputted.
Touch
or pushof the steering
wheel.
DBy phone book
You can call by phone book data which
is transferred from your cellular phone.
The system has one phone book. You
can register up to 1000 numbers.
This cannot be operated while driving.
1. Touch “Phone Book” to display
“Phone Book” screen.
IS F/350/250_Navi_U
(L/O 0808)
— Call on the Bluetooth r
phone

Finish
OTHER FUNCTIONS
135
2. Select the desired number from the
list.
Touchor pushof the steering
wheel.
DBy dialed numbers
You can call by dialed number. The sys-
tem memorizes up to 5 dialed numbers.
If it is more than 5, the oldest number is
deleted.
This cannot be operated while driving.
1. Touch “Call Log” to display “Outgo-
ing Calls” screen.
IS F/350/250_Navi_U
(L/O 0808)

Finish
OTHER FUNCTIONS
136
DWhen you call by phone book, the
name (if registered) is displayed.
DWhen you call the same number
continuously, only the newest number
is registered.
2. Select the desired number from the
list.
Touchor pushof the steering
wheel.
DBy received calls
You can call by received calls. When a
call is received, the system memorizes
up to 5 numbers. If it is more than 5, the
oldest number is deleted.
This cannot be operated while driving.
1. Touch “Call Log” to display “Outgo-
ing Calls” screen.
2. Touch “Incoming Calls” to display
the “Incoming Calls” screen.
IS F/350/250_Navi_U
(L/O 0808)

Finish
OTHER FUNCTIONS
137
DWhen a telephone number registered
in phone book is received, the name
and the number are displayed.
DReceived calls which you did not
answer are also memorized in the
system and “Abs.”is displayed on the
left side of the number.
DUnnoticed telephone number such as
a public telephone is not memorized in
the system.
3. Select the desired number from the
list.
Touchor pushof the steering
wheel.
DA international phone call may not be
made depending on the cellular phone
which you have.
DBy speed dial
You can call by registered telephone
number which you selected from a
phone book, dialed numbers and re-
ceived calls. (See “(a) Registering the
speed dial” on page 144 for registering
the speed dial.)
1. Touch “Speed Dial” to display
“Speed Dial” screen.
2. Touch the desired number to call.
You can change the page by touching
“Speed Dial 2” or “Speed Dial 3”.
When you push the telephone switch while
driving, the screen above appears. Touch
the desired name to call. (The telephone
number is not displayed.)
IS F/350/250_Navi_U
(L/O 0808)

Finish
OTHER FUNCTIONS
138
D
By voice recognition
You can call by giving a command. (For
the operation and command of voice
recognition, see “Speech command
system” on page 174 and “Help
screen” on page 177.)
DIALING BY NAME
You can call by giving a voice tag regis-
tered in the phone book. For setting the
voice recognition, see “
DSetting the
voice recognition” on page 156.
Example: Call Charlize.
You: Push the talk switch.
System: “After the beep, please say the name.”
You: “Charlize.”
System: “Charlize chosen, when ready, please briefly push the talk
switch or push the off− hook
switch to dial.”
You: Push the talk switch.
System: “After the beep, please say “Dial”.”
You: “Dial.”
System: “Dialing the name.”
Now you can call Charlize.
IS F/350/250_Navi_U
(L/O 0808)

Finish
OTHER FUNCTIONS
139
“Next” is displayed when multiple entries
are found for a searched name.
Up to 6 entries can be displayed including
the first searched one.
Do the following to change the entry to the
next one.
DTouch “Next”.
DPush the talk switch to say “Next Candi-
date”.
Calling without the voice recognition
After the entry number is displayed, you
can also call by pushing the telephone
switch or touching “Dial”.
Cancelling the voice recognition
The voice recognition will be cancelled
when you do the following.
DKeep on pushing the talk switch.
DPushof the steering wheel.
DTouch “Cancel”. (Except for recogniz-
ing the command.)
DSay “Cancel”. DIALING BY PHONE NUMBER
You can call by giving a desired num-
ber.
You: Push the talk switch.
System: “After the beep, please say the
number.”
You: “812387.”
System: “When ready, please briefly push the talk switch or push the
off−hook switch to dial.”
You: Push the talk switch.
System: “After the beep, please continue to add numbers or
say “Dial”.”
You: “Dial.”
System: “Dialing the number.”
Now you can call 812387.
IS F/350/250_Navi_U
(L/O 0808)