lock LEXUS LS430 2005 Manual Online

OCCUPANT RESTRAINT SYSTEMS
167
Center rear seat
16L279
To move the head restraint forward, pull on the top. To
move the head restraint forward or rearward, pull or push
on the top.
The head restraint is most effective when it is close to your
head. Therefore, using a cush ion on the seatback is not
recommended.
CAUTION
After adjusting the head restraint, make sure it is locked
in position.
16L278b
Push the button to return the head restraint to its original
position.

OCCUPANT RESTRAINT SYSTEMS
169
Be careful not to damage the belt webbing or
hardware. Take care that they do not get caught or
pinched in the seat or doors.
 Inspect the belt system periodically. Check for cuts,
fraying, and loose parts. Damaged parts should be
replaced. Do not disassemble or modify the system.
 Keep the belts clean and dry. If they need cleaning,
use a mild soap solution or lukewarm water. Never
use bleach, dye, or abrasive cleaners, or allow them
to come into contact with the belt they may severely
weaken the belts. (See “Cleaning the interior” on
page 515 for instructions.)
 Replace the belt assembly (including bolts) if it has
been used in a severe impact. The entire assembly
should be replaced even if damage is not obvious.Front seat belt buckle illumination
16L371
Opening the driver’s door lights up the driver’s seat belt
buckle for easy use. The same applies for the front
passenger’s door and seat belt buckle.
The light remains on for 15 seconds after the door is closed,
but goes off immediately when all the doors are locked.

OCCUPANT RESTRAINT SYSTEMS
170
Fastening front and rear seat belts
16L287
Adjust the seat as needed and sit up straight and well back
in the seat. To fasten your belt, pull it out of the retractor
and insert the tab into the buckle.
You will hear a click when the tab locks into the buckle.
The seat belt length automatically adjusts to your size and the
seat position.
The retractor will lock the belt during a sudden stop or on
impact. It also may lock if you lean forward too quickly. A slow,
easy motion will allow the belt to extend, and you can move
around freely. When a passenger’s shoulder belt is completely extended and
is then retracted even slightly,
the belt is locked in that position
and cannot be extended. This feature is used to hold the child
restraint system securely. (For details, see “Child restraint” on
page 199.) To free the belt again, fully retract the belt and then
pull the belt out once more.
If the seat belt cannot be pulled out of the retractor, firmly pull
the belt and release it. You will then be able to smoothly pull
the belt out of the retractor.
CAUTION
 After inserting the tab, make sure the tab and buckle
are locked and that the belt is not twisted.
 Do not insert coins, clips, etc. in the buckle as this
may prevent you from properly latching the tab and
buckle.
 If the seat belt does not function normally,
immediately contact your Lexus dealer. Do not use
the seat until the seat belt is fixed, because it cannot
protect an adult occupant or your child from injury.

OCCUPANT RESTRAINT SYSTEMS
175
16L292
To connect the extender to the seat belt, insert the tab into
the seat belt buckle so that the “PRESS” signs on the
buckle release buttons of the extender and the seat belt
are both facing outward as shown.
You will hear a click when the tab locks into the buckle.
When releasing the seat belt, press on the buckle release
button on the extender, not on the seat belt. This helps prevent
damage to the vehicle interior and extender itself.
When not in use, remove the extender and store in the vehicle
for future use.
CAUTION
 After inserting the tab, make sure the tab and buckle
are locked and that the lap and shoulder portions of
the belt and the seat belt extender are not twisted.
 Do not insert coins, clips, etc. in the buckle as this
may prevent you from properly latching the tab and
buckle.
 If the seat belt does not function normally,
immediately contact your Lexus dealer. Do not use
the seat until the seat belt is fixed, because it cannot
protect an adult occupant or your child from injury.

OCCUPANT RESTRAINT SYSTEMS
177
When the seat belt pretensioners are activated, an operating
noise
may be heard and a small amount of non −toxic gas may
be released. This does not indicate that a fire is occurring. This
gas is normally harmless.
Once the seat belt pretensioners have been activated, the seat
belt retractors remain locked.
CAUTION
Do not modify, remove, strike or open the seat belt
pretensioner assemblies, airbag sensor or surrounding
area or wiring. Failure to follow these instructions may
prevent the seat belt pretensioners from activating
correctly, cause sudden operation of the system or
disable the system, which could result in death or
serious injury. Consult your Lexus dealer about any
repair and modification.
NOTICE
Do not perform any of the following changes without
consulting your Lexus dealer. Such changes can
interfere with proper operation of the seat belt
pretensioners in some cases.
 Installation of electronic devices such as a mobile
twoway radio, cassette tape player or CD player.
 Repairs on or near the seat belt retractor assemblies.
 Modification of the suspension system.
 Modification of the front end structure.
 Attachment of a grille guard (bull bar, kangaroo bar,
etc.), snowplow, winches or any other equipment to
the front end.
 Repairs made on or near the front fenders, front end
structure or console.

OCCUPANT RESTRAINT SYSTEMS
205
16L311
1. Run the lap and shoulder belt through or around the infant
seat following the instructions provided by its manufacturer
and insert the tab into the buckle taking care not to twist the
belt. Keep the lap portion of the belt tight.
CAUTION
After inserting the tab, make sure the tab and buckle
are locked and that the lap and shoulder portions of
the belt are not twisted.
 Do not insert coins, clips, etc. in the buckle as this
may prevent your child from properly latching the tab
and buckle.
 If the seat belt does not function normally, it cannot
protect your child from death or serious injury.
Contact your Lexus dealer immediately. Do not
install the child restraint system on the seat until the
seat belt is fixed.
16L312
2. Fully extend the shoulder belt to put it in the lock mode.
When the belt is then retrac ted even slightly, it cannot be
extended.
To hold the infant seat securely, make sure the belt is in the lock
mode before letting the belt retract.

OCCUPANT RESTRAINT SYSTEMS
210
16L318
1. Run the lap and shoulder belt through or around the
convertible seat following the instructions provided by its
manufacturer and insert the tab into the buckle taking care not
to twist the belt. Keep the lap portion of the belt tight.
CAUTION
 After inserting the tab, make sure the tab and buckle
are locked and that the lap and shoulder portions of
the belt are not twisted.
 Do not insert coins, clips, etc. in the buckle as this
may prevent your child from properly latching the tab
and buckle.
 If the seat belt does not function normally, it cannot
protect your child from death or serious injury.
Contact your Lexus dealer immediately. Do not
install the child restraint system on the seat until the
seat belt is fixed.
16L319
2. Fully extend the shoulder belt to put it in the lock mode.
When the belt is then retrac ted even slightly, it cannot be
extended.
To hold the convertible seat securely, make sure the belt is in
the lock mode before letting the belt retract.

OCCUPANT RESTRAINT SYSTEMS
214
Both highpositioned lap belts and loosefitting
belts could cause death or serious injuries due to
sliding under the lap belt during a collision or other
unintended event. Keep the lap belt positioned as
low on a child’s hips as possible.
 For child’s safety, do not place the shoulder belt
under child’s arm.
 After inserting the tab, make sure the tab and buckle
are locked and that the lap and shoulder portions of
the belt are not twisted.
 Do not insert coins, clips, etc. in the buckle as this
may prevent your child from properly latching the tab
and buckle.
 If the seat belt does not function normally, it cannot
protect your child from death or serious injury.
Contact your Lexus dealer immediately. Do not
install the child restraint system on the seat until the
seat belt is fixed.
16L325
2. To remove the booster seat, press the buckle release button
and allow the belt to retract.

OCCUPANT RESTRAINT SYSTEMS
222Conditions for memorized position activation

Ignition switch “ON” and selector lever in “N” or “P” position
with the vehicle stopped.
All parts of the memorized positions can be activated.
 Ignition switch off and within 30 seconds of opening driver’s
door.
The memorized position can be activated, except for the tilt
and telescopic steering.
If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1”, “2” or \
“3”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch.
MEMORY CALL SYSTEM USING A SMART KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized position when you open the driver’s door after
unlocking it with a smart key. And when you push the
ignition switch, the tilt and telescopic steering is adjusted.
To activate this system, the ID of the smart key needs to
be registered in the memory button.
Registering the smart key ID code
Before the registration of the ID of the smart key, the driving
position must be memorized in the memory button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the smart key in possession, select a button in
which you want to record the ID of the key from buttons
“1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with button “1”, “2” or “3” held\
down.
When the registration is completed, one beep sounds. If the
key has already been registered, the previous memory will be
erased. If the same driving position profile for the same key is
registered in another button, that memory will also be erased.

OCCUPANT RESTRAINT SYSTEMS
223
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the smart key in which you want to cancel the
registration in possession and push the “SET” button.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with the “SET” button held
down.
When the previous key ID memory is erased, two beeps
sound.MEMORY CALL SYSTEM USING A WIRELESS REMOTE
CONTROL KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized
position when you open the driver’s door after
unlocking it with a wireless remote control key. And when
you insert the key into the ignition switch, the tilt and
telescopic steering is adjusted.
To activate this system, the ID of the wireless remote
control key ne eds to be registered in the memory button.
Registering the wireless remote control key
ID code
Before the registration of the ID of the wireless remote control
key, the driving position must be memorized in the memory
button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the wireless remote control key in possession,
select a button in which you want to record the ID of the
key from buttons “1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with button “1”,
“2” or “3” held down.