LEXUS LX570 2014 Owners Manual

2112-3. Operating the lights and wipers
2
When driving
LX570_OM_OM60L21U_(U) Automatic High Beam 
 : If equippedThe Automatic High Beam uses an in-vehicle camera sensor to assess the
brightness of streetlights, the lights of oncoming and preceding vehicles,
etc., and automatically turns high beam on or off as necessary.
■ Activating the Automatic High Beam system Push the lever away from you with
the headlight switch in the “AUTO”
position when the “ENGINE
START STOP” switch is in IGNI-
TION ON mode.
The Automatic High Beam indi-
cator will come on when the
headlights are turned on auto-
matically to indicate that the sys-
tem is active.

2122-3. Operating the lights and wipers
LX570_OM_OM60L21U_(U) ■ Turning the high beam on/off manually
Switching to low beam Pull the lever to the original posi-
tion.
Switching to high beam Turn the light switch to the
position.

2132-3. Operating the lights and wipers
2
When driving
LX570_OM_OM60L21U_(U) ■ High beam automatic turning on or off conditions
When all of the followi ng conditions are fulfill ed, high beam will be
automatically turned on (after approximately 1 second):
● Vehicle speed is above approximately 21 mph (34 km/h).
● The area ahead of the vehicle is dark.
● There are no oncoming or preceding vehicles with headlights or tail
lights turned on.
If any of the following co nditions are fulfilled, hi gh beam will be auto-
matically turned off:
● Vehicle speed drops below approximately 17 mph (27 km/h).
● The area ahead of the vehicle is not dark.
● Oncoming or preceding vehicles have headlights or tail lights
turned on.

2142-3. Operating the lights and wipers
LX570_OM_OM60L21U_(U) ■
Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam . Always drive safely, taking care to
observe your surroundings and turning high beam on or off manually if necessary.■
Camera sensor detection information ●
High beam may not be automatically turned off in the following situations:
• When oncoming vehicles suddenly appear from a curve.
• When the vehicle is cut in front of by another. ●
High beam may be turned off if an oncoming vehicle that is using fog lights with-
out using the headlights is detected. ●
Houselights, streetlights, red traffic sign als, and illuminated billboards or signs
may cause the high beam to turn off. ●
The following factors may affect the amount of time taken to turn high beam on
or off:
• The brightness of headlights, fog lights , and tail lights of oncoming and pre-
ceding vehicles
• Road conditions (wetness, ice, snow etc.)
• The number of passengers and amount of baggage ●
High beam may be turned on or off when unexpected by the driver.

2152-3. Operating the lights and wipers
2
When driving
LX570_OM_OM60L21U_(U) ●
In the situations below, the system may not be able to correctly detect the sur-
rounding brightness levels, and may flash or expose nearby pedestrians to the
high beam. Therefore, you should consider turning the high beam on or off
manually rather than relying on the Automatic High Beam system.
• In bad weather (rain, snow, fog, sandstorms etc.)
• The windshield is obscured by fog, mist, ice, dirt etc.
• The windshield is cracked or damaged.
• The inside rear view mirror or camera sensor is deformed or dirty.
• The camera sensor temperature is extremely high.
• Surrounding brightness levels are equa l to those of headlights, tail lights or
fog lights.
• Vehicles ahead have headlights that are either switched off, dirty, are chang-
ing color, or are not aimed properly.
• When driving through an area of intermittently changing brightness and
darkness.
• When frequently and repeatedly driving ascending/descending roads, or
roads with rough, bumpy or uneven surfaces (such as stone-paved roads,
gravel tracks etc.)
• When frequently and repeatedly taking curves or driving on a winding road.
• There is a highly reflective object ahead of the vehicle, such as a sign or a mir-
ror.
• The back of a vehicle ahead is highly reflective, such as a container on a truck.
• The vehicle’s headlights are damaged or dirty.
• The vehicle is listing or tilting, due to a flat tire, a trailer being towed etc.
• The Automatic High Beam indicator is flashing.
• The high beam and low beam are repeatedly being switched between in an
abnormal manner.
• The driver believes that the high beam may be causing problems or distress to
other drivers or pedestrians nearby.

2162-3. Operating the lights and wipers
LX570_OM_OM60L21U_(U) ■
If a warning message of the Automatic High Beam is displayed...
It may indicate a malfunction in the system. Contact your Lexus dealer. ■
Temporary lowering sensor sensitivity
The sensitivity of the sensor can be temporarily lowered.
To lower the sensitivity, push and hold on the inside rear view mirror for 15 to
20 seconds, and release. The indicator light on the inside rear view mirror will flash
to indicate that the sens itivity has been lowered.
When the “ENGINE START STOP” switch is turned off, the sensitivity will be
returned to its normal level. ■
Customization
The Automatic High Beam can be turned off.
(Customizable features  P. 9 0 6 )

2172-3. Operating the lights and wipers
2
When driving
LX570_OM_OM60L21U_(U) NOTICE■
Camera sensor
●
Do not touch the camera sensor. ●
Do not subject the inside rear view mirror or the camera sensor to a strong
impact. ●
Do not disassemble the camera sensor. ●
Do not spill liquid onto the inside rear view mirror or the camera sensor. ●
Do not apply window tinting or stickers to the camera sensor or the area of wind-
shield near the camera sensor. ●
Do not place items on the dashboard. There is a possibility that the camera sensor
will mistake items reflected in the windshield for streetlights, the headlights of
other vehicles, etc. ●
Do not install a parking tag or any othe r accessories near or around the inside
rear view mirror and the camera sensor. ●
Do not overload the vehicle. ●
Do not modify the vehicle. ●
Do not replace windshield with a non-genuine windshield.
Contact your Lexus dealer. Observe the following to ensure that the
Automatic High Beam functions correctly.

2182-3. Operating the lights and wipers
LX570_OM_OM60L21U_(U) Fog light switch The fog lights assist visibili ty in difficult driving conditions, such as in rain or
fog. The fog lights can be used when the headlights are on low beam.
Type A
Turns the fog lights off
Turns the fog lights on

2192-3. Operating the lights and wipers
2
When driving
LX570_OM_OM60L21U_(U) Type B
Turns the fog lights off
Turns the fog lights on

2202-3. Operating the lights and wipers
LX570_OM_OM60L21U_(U) Windshield wipers and washer When “AUTO” is selected, the wipers will operate automatically when the
sensor detects falling rain. The syst em automatically adjusts wiper timing
according to rain volume and vehicle speed.
Type A
Off
Rain-sensing wiper
operation
Low speed wiper
operation
High speed wiper
operation
Temporary operation