LEXUS RX330 2006 Owners Manual

STARTING AND DRIVING
410AREA DISPLAYED ON SCREEN
Image is displayed approximately level on screen.
Check surroundings for safety.

Corners of bumper

STARTING AND DRIVING
411

The area covered by the camera is limited. Objects
which are close to either corner of the bumper or under
the bumper cannot be seen on the screen.
 The area displayed on the screen may vary according
to vehicle orientation or road conditions. THE REAR VIEW MONITOR SYSTEM CAMERA
The rear view monitor system camera is located on the back
door as shown in the illustration. The camera uses a special
lens. The distance of the image that appears on the screen
differs from the actual distance.
In the following cases, it may become difficult to
see the images
on the screen, even when the system is functioning.
 In the dark (for example, at night)
 When the temperature near the lens is extremely high or low
 When water droplets are adhering to the camera, or when
humidity is high (for example, when it rains)
 When foreign matter (for example, snow or mud) adheres
to the camera lens
 When the sun or the beam of headlights is shining directly
into the camera lens

STARTING AND DRIVING
412
Check surroundings for safety.
If a bright light (for example, sunlight reflected off the vehicle
body) is picked up by the camera, the smear effect* peculiar to
the camera may occur.
*: Smear effect — A phenomenon that occurs when a bright
light (for example, sunlight reflected off the vehicle body) is
picked up by the camera; when transmitted by the camera, the
light source appears to have a vertical streak above and below
it.
CRUISE CONTROL
The cruise control is designed to maintain a set cruising
speed without requiring the driver to operate the
accelerator. Cruising speed can be set to any speed above
40 km/h (25 mph).
Within the limits of the engine’s capabilities, cruising speed can
be maintained up or down grades. However, changes in
vehicle speed may occur on steeper grades.
CAUTION
 To help maintain maximum control of your vehicle,
do not use the cruise control when driving in heavy
or varying traffic, or on slippery (rainy, icy or
snowcovered) or winding roads.
 Avoid vehicle speed increases when driving
downhill. If the vehicle speed is too fast in relation to
the cruise control set speed, cancel the cruise
control then downshift the transmission to use
engine braking to slow down.

STARTING AND DRIVING
413
(a) Turning the system on and off
To turn the cruise control on, press the “ON−OFF” button. The
“CRUISE” indicator light in the instrument cluster will come on
to indicate that the cruise control is operational. Pressing the
“ON−OFF” button again turns the system off.
When the system is turned off, cruising speed must be reset
when the cruise control is turned on again.
CAUTION
To avoid accidentally engaging the cruise control, turn
the system off when it is not in use. Make sure the
“CRUISE” indicator light is off.
(b) Setting operation
 Each function is described below.
1Setting the cruising speed
The transmission must be in the “D” position or the shift range
position must be “4” (fourth range) or “5” (fifth range) in “\
S”
mode (with multi−mode type) before you set the cruising
speed.
Bring the vehicle to the desired speed, press the control lever
downward in the “ − SET” direction and release it. This sets the
vehicle at that speed. Now you may take your foot off the
accelerator pedal. If you need acceleration — for example,
when passing — depress the accelerator pedal enough for the
vehicle to exceed the set speed. When you release the
accelerator pedal, the vehicle will return to the speed set prior
to the acceleration.

STARTING AND DRIVING
414
2Cancelling the cruise control
The cruise control may be temporarily cancelled by the driver
or by the system itself under certain circumstances.
Temporary cancellation allows the set cruising speed to remain
in memory.
The cruise control can be temporarily cancelled by doing the
following:
 Pulling the lever in the “CANCEL” direction and releasing it
 Depressing the brake pedal
Under certain circumstances, the cruise control is temporarily
cancelled:
 When vehicle speed falls below 40 km/h (25 mph)
 When vehicle stability control is activated
When vehicle speed drops 16 km/h (10 mph) below the set
speed, the cruise control is cancelled and the set speed is
erased from memory.
The “CRUISE” indicator light remains on to indicate that the
system is still in operation.
To turn the cruise control off, press the “ON−OFF” button.
Make sure the “CRUISE” indicator light is off.
If the cruise control automatically cancels out other than for the
above cases, have your vehicle checked by your Lexus dealer
at the earliest opportunity.3Resuming the cruise control
If the cruise control is temporarily cancelled, the cruising speed
can be resumed by pushing the lever up in the “+ RES”
direction.
Vehicle speed must be above 40 km/h (25 mph).
4Resetting to a faster speed
Press the control lever upward in the “+ RES” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held upward, the vehicle will gradually gain
speed.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
increased 1.6 km/h (1 mph) each time by pressing the control
lever upward in the “+ RES” direction quickly.
However, a quicker way to reset is to accelerate the vehicle and
then press the control lever downward in the “− SET” direction.

STARTING AND DRIVING
415
5Resetting to a slower speed
Press the control lever downward in the “ − SET” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held downward, the vehicle speed will
gradually decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the “ − SET” direction quickly.
However, a quicker way to reset is to depress the brake pedal
and then press the control lever downward in the “ − SET”
direction.
Vehicle with automatic transmission (standard type) —
Even if you downshift the transmission from the “D” position to
“4” with the cruise control on, engine braking will not be
enabled because the cruise control is not cancelled. To
decrease the vehicle speed, reset to a slower speed with the
cruise control lever or depress the brake pedal. If you use the
brake pedal, cruise control is cancelled.
Vehicle with automatic transmission (multi −mode type) —
Even if you downshift the transmission from the “D” or “5” (fifth
range) to the “4” (fourth range) with the cruise control on,
engine braking will not be enabled because the cruise control
is not cancelled. To decrease the vehicle speed, reset to a
slower speed with the cruise control lever or depress the brake
pedal. If you use the brake pedal, cruise control is cancelled.Cruise control failure warning
If the “CRUISE” indicator light flashes when using the cruise
control, press the “ON− OFF” button to turn the system off and
then press it again to turn it on.
If any of the following conditions then occurs, there is some
trouble in the cruise control system.
 The indicator light does not come on.
 The indicator light flashes again.
 The indicator light goes out after it comes on.
If this is the case, contact your Lexus dealer and have your
Lexus inspected.

STARTING AND DRIVING
416
DYNAMIC LASER CRUISECONTROL
Dynamic laser cruise control allows you to drive at a
constant cruising speeds over about 45 km/h (28 mph)
with your foot off the accelerator pedal, maintaining an
appropriate vehicletovehicle distance between the
vehicle ahead.
CAUTION
Do not rely excessively on dynamic laser cruise control
in order to avoid serious injury or death, or to prevent
accidents or to control the vehicle’s speed in
emergency situations. Do not use cruise control except
in appropriate road and traffic conditions. Always drive
carefully and attentively. Before using dynamic laser
cruise control, read and understand the following
instructions.1Cruise control switch
2Distance switch
3Display
4“NORM.” indicator light
(conventional cruise control mode indicator light)
5“CRUISE” indicator light
6“READY” indicator light
(ready mode indicator light)
7Master warning light

STARTING AND DRIVING
417
Dynamic laser cruise control mode
1Vehicletovehicle distance control mode
2Conventional cruise control mode
The dynamic laser cruise control function has two cruise
control modes.
 Vehicle −to−vehicle distance control mode for maintaining
an appropriate distance between vehicles
 The conventional cruise control mode for cruising at
constant preset speeds
You can change the mode by using the control lever.
The two cruise control modes function dif ferently. When using
dynamic laser cruise control, always confirm which mode is
selected. For the vehicle
−to−vehicle distance control mode, see
“Vehicle −to−vehicle distance control mode” on page 418. For
the conventional (fixed speed) cruise control mode, see
“Conventional (fixed speed) cruise control mode” on page 433.

STARTING AND DRIVING
418
Vehicletovehicle distance control mode
The system’s laser radar sensor detects the reflectors of
vehicles and measures the vehicletovehicle distance.
The detection range of the sensor is about 120 m (400 ft.)
ahead.
CAUTION
Dynamic laser cruise control is not a
collisionavoidance system and will not prevent
accidents. Dynamic laser cruise control is a vehicle
speed control device that is intended for use only on
freeways or roads where the traffic is light or moderate.
To avoid serious injury, you must use caution and be
attentive to road and traffic conditions while using
dynamic laser cruise control.
(a) Dynamic laser cruise control operations

STARTING AND DRIVING
419
The dynamic laser cruise control function operates
automatically and depending on whether a vehicle is
detected ahead may change the
speed of your vehicle as
follows.
If no vehicle is running ahead of you —
1Cruising at a fixed speed: If there is no vehicle detected
ahead, your cruising speed is maintained at the preset
speed from about 45 km/h (28 mph) to about 135 km/h (85
mph). The preset speed is displayed in the display. For
the vehicle speed setting, see “(c) Setting the cruising
speed” on page 424. If a vehicle is detected ahead of you —
2Deceleration cruising function: If a slower moving
vehicle is detected ahead of you, your vehicle cruising
speed decreases within the range of about 40 km/h (25
mph) to 135 km/h (85 mph). The display shows the preset
speed, the detected vehicle ahead and selected
vehicle
−to−vehicle distance. If your vehicle gets closer to
the vehicle ahead because of insufficient automatic
deceleration, then the alarm warns you to also manually
apply brakes.
3Followup cruising function: After deceleration, your
cruising speed changes to match the speed of the vehicle
ahead in order to maintain a constant vehicle −to− vehicle
distance. The following distance can be changed. For
details, see “(h) Changing vehicle −to−vehicle distance”
on page 427.