change wheel MAZDA 323 1992 Workshop Manual Suplement

The following chart shows interchangeability of the main parts of the previous BP DOHC Turbo engine
and the new BP DOHC Turbo engine for 4WD models.
S ymiols: 0 _. lnterc hangeable X . . . Not Interchangeable
Part name tnterchangeability
Remark
Cytlnder head 0
Camshaft 011 seal 0
Cvllnder head bolt 0
CB :
Cyh nder
blcck
related
Crankshaft
related
Timing belt
related
Valve
related
Lubrication
system
related Cylrnder head gasket 0
Wnder head cover 0
Cylinder head cover gasket
Cylinder block
MaEn bearina cao 0
0
0
Ma+n bearino suo~oFt elate I
0 I ” ,I I
Oil pan
Timrno belt cover I X
0 I
Turbocharger oil return pipe hole increased from
13mm IO.51 in) to 17mm IO.67 in)
Seal elate
Front orl seal I 0 I
I I 0
1
Rear 011 seal 0
Crankshaft 0
Marn bearina 0
Thrust bearing
Connectmg rod
Connecting rod beartng
Piston 0
;J
X
Shape different
Piston skirt shortened
I Piston pm cl
Tw
X Sectional shape different
Piston rrng Piston ring end gap increased from 0:?5--0.30mm
Second
X ~0.006-0.011 in ) to 0.35-0.50mm IO.01 4-0.019
in ] (Measured In cylinder)
Crankshaft pulley Shape different
Rear cover ;5
Flywheel
I 0
Flywheel bolt 0
Tbmlng belt 0
Timing belt crank pulley 0
Camshaft pulley 0
Timing belt tensioner and spring
0
Idler 0
Camshaft 0
AA
Valve Intake
Exhaust
cl
0
X Metallic sodium-filled valve
Valve spring Intake
I 0
and seat
Exhaust 0
Vatve wide I 0
Valve seal
Oil pump 0
Oil pump gasket 0
oil strainer 0
Oil strainer gasket 0
Oil cooler
X Heat dissi patlon capacity increased
Oil jet
Oil filter Shape different
1 Water pump 0
Coohng Thermostat 0
system
related Radiator 0
Cooling fan 0
I 3EO32.304
BZ-3.

SUPPLEMENTAL SERVICE INFORMATION .
I
The following points in this section are changed in comparison to the Mazda 323 4-Wheel Drive Work-
shop Manual [I 229-l O-89t].
Turbocharger
l Removal / Installation
Wastegate solenoid valve
l Inspection
htercooter
l Removal I Installation
Fuel pump (main)
l Inspection
Fuel pump resistor/relay
l System operation
l Inspection
Injector
l Inspection
l Volume test
Injector resistor
l Inspection
Pressure regulator control system
l Solenoid valve (pressure regulator control}
Engine control unit (ECU)
l Inspection 13EOF3.320
F3-I 5

%
:
1 SUPPLEMENTAL SERVICE INFORMATION, WHEELS AND TIRES Q .
SUPPLEMENTAL SERVICE INFORMATKM
The following point in this section is changed in comparison with the Mazda 323 Workshop Manual Voi-
ume 2 (1206~IO-89F).
l Wheels and tires
I Wheel balance adjustment
13EOQX-30 13EOUX-305
j
WHEELS AND TIRES
I
WHEEL BALANCE ADJUSTMENT
If a wheel becomes unbalanced or if a tire is replaced or
repaired, the wheel must be rebalanced to within specifi-
cation.
Maximum unbalance (at rim edge): 9 g IO.32 oz j
Caution
l Do not use more than two balance weights on the
inner or outer side of the wheel,
l One batance weight; max. 60 g (2-f oz 1.
l if the total weight exceeds IOU g (3.5 or] on one
side, rebalance after moving the tire around on the
rim.
l Attach the balance weights tightly to the wheel.
. Select suitable balance weights for aluminum alloy
wheels.

R OUTLINE
OUTLINE
OUTLtNE OF CONSTRUCTION
l The%onstruction and operation of the suspension system are basically the same as for previous models.
l The coil spring and shock absorber specifications are changed.
l The stabilizer specifications are changed.
SPECIFICATIONS
13EORX-302
Front suspension
Suspension type
Sprmg type
Shock absorber
Stabrlmr
Specifications
Strut
Coil spring
Oil filled Total toe-rn
Front
wheel
atignment
(‘Unladen)
Rear suspension
Suspensron type
Sprmg type
Shock absorber
Stabrlrzer
Rear wheei
alrgnment
(‘Unladen) Maximum steering 38* f 3*
309 f 30
-0045 f 45’
2035’ f 45’
KIngpin angle degree
12*to’
We Oil fifled
Damprng force N [ kgl Ibf 1 .‘? .@g,$g&;qJ&,$. ‘: ‘., . . ” ‘, : :,
at 0.3 m 112
]ls I Contraction ;. ~ .. . . . . .__. ..:, .. .. ,I. ._ :. . . f: ; _... .:
Type Torsion bar
Diameter mm. f in ]
19.t (0.751
Total toe-in mm fin!
2.h 3 (0.08 f 0.121
degree
O”12’ f 18’
Camber angle degree -0°20’ f 45’
13EORX-303
l Fuel tank full, radrator coolant and engine oil at speclfled levels; and spare tire, jack, and tools in designated positions. Front Coil Spring Specifications
1 Identification mark color Wire diameter Coif .center
M l l
I Free length A a2 mm lin)
diameter mm [in) . mm 1 in) Coil number Rear Coil Spring Speci?ications
ldentlfication mark color M” Wire diameter Coil center
Free length
mm {in) diameter mm 1 in J
mm {in) Coil number
*’ Maln Identlfcatlon mark on second cgil from bottom.
*’ Auxrllary &entificatton mark on thrrd coil from bottom.
Shaded areas tndcate
new specifrcat+ons 13EORXCS05
(I .f

S SUPPLEMENTAL SERVICE INFORMATION
SUPPLEMENTAL SERVICE lNFORMATlON
The following points in this section are changed in comparison with 323 Workshop Manual (1229-~()439~).
*
BONNET BULGE
l Removal / installation
FRONT BUMPER
l Removal / Installation
REAR SKIRT
l Removal / Installation
WHEEL ARCf-f MOLDfNG
l Removal / Installation
13EOSX-310
S-6
BONNE
COMPOh
Rembvaf
1. Removi
2. lnstatl if