sensor MAZDA 323 1992 Workshop Manual Suplement

GI MAINTENANCE NOTE
VIEWED
.OM BELOW
‘REE
13EGfX-307
I
I t3EGIX-308 CHASSIS DYNAMOMETER CHECK
Caution
l Do not clutch abruptly. l Do not attempt rabbit starts or accelerate quickly.
1. Remove the propeller shaft.
2. Lock the center differential (2WD).
3. Place the front wheets on the roller.
4. Lock the rear wheels and apply the parking brake.
5. Drive the tester roller and check.
6. Upon completion of the test, gradually decelerate with soft
braking and stop the engine.
7. When the test is done, return the differential lclck rod to the
free condition (4WD) and reinstall the propeller shaft.
WHEEL BALANCER (On-the-car Balance)
1.
Jack up all four wheels. Support the wheels to be checked
(front or rear) with the wheel balancer sensor stand and the
remainrng wheels with safety stands.
2. Set the on-the-car balancer. With the center differential in
free condition, drove the tires with the engine; then check.

A PRE-DELIVERY INSPECTION TABLE
PRE-DELIVERY INSPECTION TABLE
[EXTERlORI
INSPECT and ADJUST, of necessary. the followlng Items to
specrfrcatron:
0 Glass, exterior bright metal and paint for damage
0 Wheel lug nuts
0 Tire pressures
0 All weatherstrips for damage or detachment
0 Operation of bonnet release and look
0 Operation of trunk Ild, hatch and fuel lbd opener
(of equipped)
0 Door operation and alignment
0 Headtrght aiming
INSTALL the foltowrng parts
0 Wheel caps or rrngs (if equipped)
0 Outsrde mirror(s)
1 UNDER BONNET-ENGINE OFF j
INSPECT and ADJUST. If necessary, the following items to
specrflcatlon.
0 Fuel, coolant and hydraulic tines, fittings, connectlons and
components for leaks
0 Engine 011 level
0 Power steering fluid level (of equipped)
0 Brake master cylinder fluky levels
0 Clutch master cylinder fturcl levels (If equipped)
0 Wtndshreld washer reservojr flurd level
0 Radiator coolant level and specrfic gravity
0 Tightness of water hose clamps
0 Tightness of battery terminals, electrolyte level and specific
gravity
0 Manual transaxle oil level
0 Drive belt(s) tension
Cl Carburetor lrnkage (choke control, wrde open throttle posi-
tion. etc ) (carburetor model only)
q Accelerator cable and linkage for free movement
0 Headlight cleaner and flurd level (if equipped)
BLEED air from fuel line (diesel engrne only)
CLEAN the spark plugs (except for diesel engine)
piEi6F]
INSTALL the following parts
0 Rubber stopper for rnsrde rear view mirror (if equjpped)
0 Fuse for accessories
CHECK the operation of the following items.
0 Seat controls (sliding and reclining) and head rest
0 Seat belts and warning system
Cl Ign&on switch and steering lock
0 Power window (if equipped)
D Door tacks including child proof door locks
Cl Inhibitor switch (ATX only)
Cl All Ikghts rncluding warning and Indicator lbghts
0 Ignition key reminder buzzer (If equipped)
A-Z
0 Horn, wbpers and washers (front and rear, If equipped)
0 Antenna (tf equipped)
0 Cigarette Ibghter and clock (if equipped)
0 Remote control outside mirror (if equrpped)
0 Heater, defogger and air conditioner at various mode selec-
tions (if equlppedj
0 Sunroof (If equipped)
CHECK the following items
0 Presence of spare fuse
0 Upholstery and Interior finish
CHECK and ADJUST, If necessary, the followjng items:
IJ Operation and fit of windows
0 Pedal height and free play of brake and clutch pedal
0 Parking brake UNDER BONNET-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
0 Operation of Idle-up system for air condbtroner or power steer-
ing (if equrpped)
0 Automatic transaxle flurd levet
0 tnltial ignrtlon timing (except disel engine)
0 Idle speed
0 Operation of throttle positron. sensor (EGI engrne)
0 Operation of cold start device and glow plug warning light
(diesel engine only)
0 Operation of dash pbt (EGI.engine)
fTiGGJ
CHECK the following items.
0 Underside fuel, coolant and hydraulic Irnes, ftttlngs, connec-
tions and components for leaks
0 Trres for cuts or brurses
0 Steering Itnkage, suspensron, exhaust system and all under-
side hardware for .looseness or damage 1 ROAD TEST j
CHECK the following items
0 8rake operation
0 Clutch operation
0 Steering control
!ZI Operation of meters and gauges
Cl Squeaks, rattles or unusual noises
Cl Engine general performance
0 Emergency locking retractors 1 AFTER ROAD TEST ]
REMOVE the seat and floor mat protective covers
CHECK for the necessary owner information materials, took
and spare tire
m vehicle
93EOAX-002
-- MAIN Char3 t: In
A: PC R: F!t T: Ti! Emis! The ed : to t!

A SCHEDULED MAtNTENANCE SERVtCES (Europe)
Maintenance Number of months or km (miles), whichever comes first
Months” - 6 12 18 24 30 36 42 48
Kllometers 1,000 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000
{Miles)
(600) (6,000) f[t2,000) (18,000) (24,000) (3U,OOO) (36,000) (42,000) {48,000), Engine
Intake and exhaust manrfold nuts (Bolts)
Drive belts”
i Engine trmlng beltW3
Engine oil (Turbo)‘4
01 filter
l *
Cool!ng system (Includtng
coolant level adlustment)
Engrne coolant T T T
A A A
A A
Replace every 100,000 km (60,000 miles)
Replace every 5,000 km (3,000 miles) or 6 months
R R R R R 1 R R R
I I I I
I
Replace every 2 years Fuel system
Idle speed
Air cleaner element * 5
Fuel
falter
Fuel Ilnes and hoses Ignition system
A f 1
I R I R
R R
I I f t I ~
lnlttal rgnrtloh trmlng 1 I I I I I I I I
Spark plugs A
A. A A
Spark plugs (Only for Sweden) Adjust every 30.000 km (t8.000 mrls) Evaporative emission control system
Throttle sensor Throttle sensor (Only for Sweden)
Evaporative system
Evaporatrve system (Only for Sweden) 1 A 1 1 A 1 1 A 1 ) A
Adjust every 80,000 km (48,000 miles)
1 I 1 1 I’ 1 1 I 1 1 I
Inspect every 80,000 km (48,000 mites) Electrical system
Battery electrolyte level and specific gravity 1 I f I I I
All Electrical system
l ’ 1 I
I 1 I I I
1 . 1 I I
Headlight alrgnment 1 A A A . A. Chassis and body
t 3EOAX-303
A-4 Chas
SW31 Rear
Tires
Hing
Seat

F3 OUTLINE
OUTLINE
OUTLINE OF CONSTRUCTION
Theefuel and emission control system of the new 323 4WD model 1s basically the same as that of the prevr-
ous 323 4WD model; however some parts are changed. The changed parts and interchangable parts
are shown betow.
13EOF3-304
Changed parts
1 ~ components Contents and purpose Reference pagl
INTAKE AlR
SYSTEM Turbocharger
Intercooler
l Size Increased for greater boost pressure l Wastegate solenord valve IS lozated on Intake port of F3-10
turbocharger to make system more compact F3-37
Volume increased for Improved F3-10
t F3-39
Wastegate sojenold valve
l Wastegate solenoid valve changed to duty solenoid
type for Increased engine power and response
l Wastegate solenoid valve is located on Intake port of
turbocharger to make system more compact F3-1 f
F3-38
I r
Pressure regulator One-stage operattlon changed to two-stage operatron F3-14
to improve hot restarting f3-41
L
FUEL SYSTEM High-ohmic type change to low-ohmrc type with exter-
Fuel qector na solenoid reslstor for improved fuel supply during F3-12
high-speed driving F3-42
Fuel pump reslstor Resistance reduced for
surer fuel supply F3-40
CONTROL
SYSTEM Pressure
regulator control system
Atr flow meter Two-stage operatton used to Improve hot restarting
Measures larger amount of air flow Increased power
Resistance values changed F3-t4
F3-43
F3- 9
f3EOF3-305 lnterchangable parts
tntake air system
l
Air valve
l Air bypass valve
l Air cleaner
l Air cleaner element
Fuel system
l Fuel filter assembly
l Fuel pu.mp (transfer
l Fuel vapor valve Control system
. l Throttle sensor
l Water thermosensor
l Knock sensor and control unit
l Oxygen sensor
l Fuel pump control unit
l Main relay
l Circuit opening relay
l Check valve (two-way) .
Evaporative system
l Charcoal canister
l Check valve (two-way)
13EOF3-306
F3-4

CHECK VALVE SOLENOID VALVE
(PURGE CONTROL)
llll
*
SOLENOID VALVE
(PRC LOW TEMP.)
3 ~NTERCOOLERII’ I ,‘/ I
II II
’ f frrmvmlHHt-----lHt I -1 II II
IIt - --M:l, i -KNmK~[I~ ,
’ ISC VALVE
VALVE WATER CHAkCOAL
CANISTOR
CHECK VALVE
I FUEL FUEL FILTER
PUMP
I FUEL FILTER
TRANSFER
PUMP
AIRkLOW METER
(WITH INTAKE AIR THERMOSENSOR)
DISTRIBUTOR
CATALYTIC CONVERTER
l TO ENGINE CONTROL UNIT

F3 OIJTUNE
SPE
* TEN
The @
ECU RELATtONSHtP DtAGRAM
1NPUT DEVICE
KNOCK SENSOR
c AIRFLOW METER
KNOCK
DlSTRlBUTOR
91c YfTC”
THERMOSENSOR
OXYGENSENSOR N EUTRAti
CLUTCH SWITCH
CONNECTOR
(TEN TERMINAL,)
INTAKE AIR
OUTPUT
DEVtCE THERMOSENSOR
{AIRFLOW METER)
CIRCUIT
OPENING
TURBOCHARGE
jAGNOSE
ONNECTOR
EN/MEN TERMINA
h SOLENOID VALVE
(PRESSURE REGUL+TOR
CONTROL)
WASTEGATE
SOLENOID VALVE IGNITER
- - (TURBtiHARGER)
FUEL PUMP
RESlSTORlRELAY
SOLENOID VALVE
(PURGE CONTROL)
F3-8 13EOF3-311

TURBOCHARGERCONTROL F3
WASTEGATE CONTROL
The engine control unit controls the wastegate solenoid valve by duty signals to better control the boost
pressure, increasing the engine’s power and response.
*
13EOF3.313
System Diagram r
DUTY VALVE
INTAKE AIR THERMOSENSOR (AIRFLOW METER)

:
:
1 , ._.s_ , -. _ ._>_ ‘r--A.-
_, . :. . . . . .-
CONTROL SYSTEM F3
CONTROL SYSTEM
STRUCTURAL VtEW
SOLENOID VALVE
PRESSURE RE
LUTCH SWlTCH
FUEL INJ RELAY
NTAKE AIR THERMOSENSOR
AIRFLOW METER)
WATER THERMOSENSOR
F3-13

F3 CONTROL SYSTEM
PRESSURE REGULATOR CONTROL SYSTEM
SOLENOID VALVE TO MAIN RELAY
(PRC HIGH TEYP.)
t ECU
I
PRESSURE REGULATOR
// VACUUM

IJ WATER
THERMOSENSOR
F----------- lNTAKE AIR
THERMOSENSOR
SWITCH SOLEltolD VALVE
(PRC LOW TEMP.)
TO FUEL TANK
13EOF3-31 To prevent vaporlock in the fuel system during hot restart idle, a two-stage pressure regulator is adoped
to the new 323 4WD.
Low temperature operation: The vacuum to the pressure regulator (A and B ports) is cut (solenoid valve
[low temp.] UN), and the fuel injection pressure is increased to 284 kPa (2.90 kgf/cm2, 41 psi ) ,
High temperature operation: The vacuum to the pressure regulator (A port) is cut (solenoid valve [high
temp.] ON), and the fuel injection pressure is increased to 343 kPa [ 3.5 kgf/cm2, 49 psi 1.
Condition and operation
Condition Operation
1
coolant Intake alt Solenoid vrlve Solenoid vatve Opemtlon
I temperature temperature Engine (Idw temp.)
(high temp.) time Operation 40% [fU40f)-
Above 90°C 5U°C (t22OFI ON OFF 180s Low temp.
f f940Fj No load
Above 5O*C
I122OF) OFF ON 210s t-ltgh temp.
3
t3EOF3-319
F3-14 Wast
l Ins fuel
l In:; InJeci
l In:;
l Vol Injecl
l In:;
Presr
l SCI Engir
l InsI

F3 SELF-DIAGNOSIS FUNCTfON
SELF-DIAGNOSIS FUNCTION
OUTLINE
Theself-diagnostic function and diagnosis procedure are the Same as for the previous 4WD model. How-
ever, there is an additional service (malfunction) code (N0.35) for the new modet.
13EOF3-321
SERVICE CODE NUM8ERS
Sensor or
subsystem
NE-signal
G stgnal
Knock sensor I Malfunction display
Cond &ion Fail-safe
Service
code no. Output signal pattern
No NE-signal
ON
-
02
OFF
M
No G srgnal Cancels two-group injection ON
03
OFF
ml
Open or short circuit
pressure sensor
F3-16
--
I