ECO mode MAZDA 626 1987 Owner's Guide

TECHNICAL DATA 30
4C. FUEL AND EMISSION CONTROL SYSTEM (FE DOHC)
Item ^Engine^model Unleaded fuel Leaded fuel

Idle speed rpm With test connector grounded 750
± 50
Throttle body

Type Horizotal draft (2-barrel)
Throat diameter mm (in) No.1 46 (1.8) Throat diameter mm (in) No.
2
40 (1.6)

Fuel pump

Type Impeller (in tank)
Output pressure kPa (kg/cm2,
psi)
Main pump: 441—588 (4.5—6.0, 64—85)
Transfer pump: 20—25 (0.20—0.25, 2.8—3.6)
Feeding capacity cc (cu in)/10 seconds Main pump: 220 (13.4) min. Transfer pump: 190 (11.6) min.

Fuel filter

Type Low-pressure side Nylon element Type High-pressure side Paper element

Pressure regulator

Type Diaphragm
Regulating pressure kPa (kg/cm2, psi) 235-275 (2.4 -2.8, 34-40)

Injector

Type High-ohmic
Type
of
drive Voltage
Resistance
ft
12--16
Injection amount cc (cu in)/15 seconds 66-91 (4.03-5.55)

Idle speed control valve

Solenoid resistance Q 6.3--9.9

Fuel tank

Capacity liters (US gal, Imp gal) 60 (15.9, 13.2) 57 (15.0, 12.5): 4-wheel steering vehicle

Air cleaner

Element type Dry

Fuel

Specification Unleaded (95 RON
or
more) i Leaded (95 RON
or
more)

30-21

30 TECHNICAL DATA
7A. MANUAL TRANSAXLE
Engine model FE DOHC Ffl FE FE
B
valve F8 Item —— Leaded UriBsded Ffl 12 valve Carb. Fl F8 RF-N RF-CX

Transmission
Shift
lever
position Floor shift
Gear ratio
First 3.307
Second 1.833
Third 1.310
Fourth 1.030
Fifth 0.837
1,233
0.970
0.795
0.914

1.161
0.861

0.755 0.680
Reverse 3.166
Oil capacity liters US qt, Imp
qt)
3.35 (3.6, 3.0)
Fluid type
ATF: DEXRON-II
Above 0°F: API GL-4
or
GL-5
SAE80W—90
or
SAE90

Clearance

Clearance
of
lever and reverse idle
gear
mm (in)

Standard 0.1—0.32 (0.004-0.013) Clearance
of
lever and reverse idle
gear
mm (in)
Wear limit 0.5 (0.020)
Clearance
of
shift fork and clutch hub sleeve
mm (in)

Standard 0.2—0.4 (0.008-0.016) Clearance
of
shift fork and clutch hub sleeve
mm (in)
Wear limit 0.5 (0.020)
Clearance
of
synchronizer ring
and

gear
mm
(in)
Standard 1.5 (0.059) Clearance
of
synchronizer ring
and

gear
mm
(in) Wear limit 0.8 (0.021)
Gear thrust clearance
mm (in)
First Standard 0.05—0.28 (0.002-0.011)
Gear thrust clearance
mm (in)
First Limit 0.3 (0.020)
Gear thrust clearance
mm (in)
Second Standard 0.18—0.46 (0.007-0.018)
Gear thrust clearance
mm (in)
Second Limit 0.5 (0.02) Gear thrust clearance
mm (in) Third Standard 0.05-0.20 (0.002-0.008)
Gear thrust clearance
mm (in) Third Limit 0.25 (0.010)
Gear thrust clearance
mm (in)
Fourth Standard 0.17—0.37 (0.0064—0.014)
Gear thrust clearance
mm (in)
Fourth Limit 0.4 (0.016)
Bearing preload
of
primary shaft gear
Primary shaft
0.1-0.25 N-m (1.0-2.5 cm-kg, 0.86-2.18 in-lb) Secondary shaft 0.2-0.4 N-m (2.0—4.0 cm-kg, 1.7-3.4 in-lb)
Bearing preload adjust shim mm (in) 0.25 (0.010), 0.30 (0.012), 0.35 (0.014), 0.40 (0.016), 0.45 (0.018), 0.50 (0.020), 0.55 (0.022), 0.60 (0.024), 0.65 (0.026), 0.70 (0.028), 0.75 (0.030), 0.80 (0.031)

Drive and differential

Final gear
TvDe

Reduction ratio
Side
bearina Dreload

Helical aear
4.1051 3.850 4.1051 3.850
4.150

1.4-2.0 N
m
(14—20 cm-kg, 12-17 in-lb)
Bearing preload adjust shim mm (in)
0.10 (0.004), 0.15 (0.006), 0.20 (0.008), 0.25 (0.010), 0.30 (0.012), 0.35 (0.014), 0.40 (0.016), 0.45 (0.018), 0.50 (0.020), 0.55 (0.022), 0.60 (0.024), 0.65 (0.026), 0.70 (0.028), 0.75 (0.030), 0.80 (0.031), 0.85 (0.033), 0.90 (0.035), 0.95 (0.037), 1.00 (0.039), 1.05 (0.041), 1.10 (0.043), 1.15 (0.045), 1.20 (0.047)
Backlash
of
side aear and
Dinion
aear mm (in) 0-0.1 (0-0.004)

30—26

30 TECHNICAL DATA
Item Engine model FE engine F6 engine
Front clutch

Number
of
driven and drive plates 3
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Front clutch clearance mm (in) 1.6-1.8 (0.063-0.071)
Retaining plate sizes mm (in) 5.2 (0.205), 5.4 (0.213), 5.6 (0.220),
5.8 (0.228), 6.0 (0.236), 6.2 (0.244)
Return spring free length mm (in) 26.2 (1.031)
Drum bushing inner diameter mm (in) Standard 44.000-44.025 (1.732-1.733) Drum bushing inner diameter mm (in) Maximum 44.075 (1.735)
Front clutch drum end play mm (in) 0.5-0.8 (0.197-0.0315)
End play adjust shims mm (in) 1.3 (0.0512), 1.5 (0.0591), 1.7 (0.0669), 1.9 (0.0748), 2.1 (0.0827), 2.3 (0.0906),
2.5
(0.0984), 2.7 (0.1063)

Rear clutch

Number
of
driven and drive plates 4
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Rear clutch clearance mm (in) 0.8--1.0 (0.0315- 0.0394)
Retaining plate sizes mm (in) 4.8 (0.189), 5.0 (0.197), 5.2 (0.205), 5.4 (0.213),
5.6 (0.220), 5.8 (0.228), 6.0 (0.236), 6.2 (0.244)
Return spring free length mm (in) 26.2 (1.031)

Low and reverse brake

Number
of
low and reverse brake plates 4
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Low and reverse brake clearance mm (in) 0.8-1.05 (0.032-0.041)
Retaining plate sizes mm (in) 4.6 (0.181),
4.8
(0.189), 5.0 (0.197), 5.2 (0.205), 5.4 (0.213), 5.6 (0.220)
Return spring free length mm (in) 27.7 (1.091)

Servo

Return sprina free lenath mm (in) 48.0 (1.89) 45.5 (1.79)

Governor

Primary spring mm (in) Outer diameter 9.0 (0.354) Primary spring mm (in) Free lenath 17.2 (0.667)
Secondary spring mm (in) Outer diameter 9.25 (0.364) Secondary spring mm (in) Free lenath 13.2 (0.520)

One-wav clutch

Bushing diameter mm (in) Standard 129.987-130.013 (5.118--5.119) Bushing diameter mm (in) Maximum 130.063 (5.121)

Control valve SDrinas
Spring name Outer dia. mm (in) Free length mm (in) Wire dia. mm (in)

Throttle backup spring 7.3 (0.287) 36.0 (1.417) 0.8 (0.031)
Downshift sorina 5.55 (0.219) 21.9 (0.862) 0.55 (0.022)
2-3 shift spring 6.9 (0.272) 41.0 (1.614) 0.7 (0.028)
1-2 shift spring 6.4 (0.252) 31.63 (1.245) 0.4 (0.016)
Second lock spring 5.55 (0.219) 33.5 (1.319) 0.55 (0.022)
Pressure reaulator sprina 11.7 (0.461) 43.0 (1.693) 1.2 (0.047)
Throttle relief ball spring 7.0 (0.276) 11.2 (0.441) 0.9 (0.035)
Orifice check valve sprina 5.0 (0.197) 15.5 (0.610) 0.23 (0.009)

30-34