transaxle MAZDA 626 1987 Repair Manual

7A TRANSAXLE CONTROL
TRANSAXLE CONTROL
REMOVAL AND INSTALLATION
1. Jack up the vehicle and support it with safety stands.
2. Remove in the sequence shown in the figure.
3. Install in the reverse order of removal. 61G07X-165
86U07A-230
1. Change lever knob
2. Assist boot
3. Mounting rubber boot
4. Bolts and nuts
5. Change control rod
6. Bracket installation nuts
7. Nut and washer
8. Extension bar bracket as-
sembly and gasket
9. Bushing
10. Pipe
11. Change lever
12. Spring
13. Ball seat (upper)
14. Bushings
15. Boot
16. Holder
17. Ball seat (lower)
18. Extention bar
Note
Apply a coat of grease (lithium base, NLGI No. 2) to the change lever ball, the ball seats,
and each joint.
7A-58

TRANSAXLE CONTROL 7 A
63U07A-151
61G07X-192
63U07A-153
Spring
Remove the spring by prying on the hooked part of
the spring with a screwdriver.
INSPECTION
Check the following, and replace if necessary:
1. Bent control rod.
2. Wear, damage, or malfunction of any joint.
3. Damaged gear shift lever ball.
4. Weak spring.
5. Wear or damage of bushing.
INSTALLATION
Install in the reverse order of removal and note the
following:
Extension Bar
First, install the extension bar to the floor, and then
install it onto the transaxle.
Tightening torque:
31—46 Nm (3.2—4.7 m-kg, 23—34 ft-lb)
Bracket Installation
Tighten the bracket installation nuts to the specified
torque.
Tightening torque: 7—10 N-m
(70—100 cm-kg, 61—87 in-lb)
76G07A-071
7A-59

7A TRANSAXLE CONTROL
Gear Shift Lever Ball
Apply grease to the ball seat surface, and install the
upper and lower ball seat, holder, and boot.
Note
Apply grease to all joints.
61G07X-193
Spring
Make sure that the hooked part of the spring is
properly seated in the bracket groove, as shown in
the figure.
63U07A-156
Bracket Cavity
Put grease in the bracket cavity.
63U07A-157
Change Control Rod
Install the change control rod so that its relationship
with the shift lever is as shown in the figure.
Tightening torque:
16—22
N
m (1.6—2.3 m-kg, 12—17 ft-lb)
61G07X-195
7A-60

7B
AUTOMATIC TRANSAXLE
(Electronically Controlled and 4-Speed)
OUTLINE 7B— 2
SPECIFICATIONS 7B— 2
COMPONENT LOCATION 7B— 3
STRUCTURAL VIEW 7B— 5
OPERATION OF COMPONENTS 7B— 6
FLUID PASSAGE LOCATION 7B— 9
TROUBLESHOOTING (G4A-EL) 7B— 12
GENERAL NOTE 7B— 12
STEP 1
(WARNING CODE RETRIEVAL) 7B— 15
STEP 2
(PRELIMINARY INSPECTION) 7B— 22
STEP 3 (SIGNAL INSPECTION) 7B— 24
STEP 4 (STALL TEST) 7B— 27
STEP 5 (TIME LAG TEST) 7B— 30
STEP 6 (OIL PRESSURE TEST) 7B— 31
STEP 7 (ROAD TEST) 7B— 34
TROUBLESHOOTING (G4A-HL) 7B— 41
GENERAL NOTE 7B— 41
STEP 1
(PRELIMINARY INSPECTION) 7B— 44
STEP 2 (ELECTRICAL
SYSTEM INSPECTION) 7B— 47
STEP 3 (STALL TEST) 7B— 49
STEP 4 (TIME LAG TEST) 7B- 52
STEP 5 (ROAD TEST) 7B— 53
STEP 6 (OIL PRESSURE TEST) 7B— 58
ELECTRICAL SYSTEM
COMPONENTS 7B— 63
MODE SWITCH (G4A-EL) 7B— 63
HOLD SWITCH (G4A-EL) 7B— 63
OD OFF SWITCH (G4A-HL) 7B— 64
INHIBITOR SWITCH 7B- 65
WATER TEMPERATURE SWITCH 7B— 66
FLUID TEMPERATURE SWITCH
(G4A-EL) 7B— 66
BRAKE LIGHT SWITCH
(G4A-EL) 7B— 66
KICK-DOWN SWITCH (G4A-HL) 7B— 67
PULSE GENERATOR (G4A-EL) 7B- 68
VEHICLE SPEED SENSOR
(G4A-EL) 7B— 68
CRUISE CONTROL SWITCH
(CRUISE CONTROL UNIT) 7B— 68
IDLE SWITCH AND THROTTLE
SENSOR (G4A-EL) 7B— 68
OD RELEASE SOLENOID
VALVE (G4A-HL) 7B— 68
SOLENOID VALVES (G4A-EL) 7B— 69
NO LOAD SIGNAL (G4A-EL) 7B— 69
MODE, AND HOLD INDICATOR
LIGHT (G4A-EL) 7B— 69
OD OFF INDICATOR LIGHT
(G4A-HL) 7B— 69
EC-AT CONTROL UNIT
(G4A-EL) 7B— 69
ON-VEHICLE MAINTENANCE 7B— 71
AUTOMATIC TRANSAXLE
FLUID (ATF) 7B— 71
SELECTOR LEVER 7B— 72
THROTTLE CABLE 7B— 73
CONTROL VALVE BODY 7B— 77
OIL STRAINER 7B— 79
ADJUSTMENT OF 2-4 BRAKE
BAND 78— 80
REPLACEMENT OF
DRIVESHAFT OIL SEAL 7B— 80
OIL COOLER 7B— 81
GOVERNOR (G4A-HL) 7B— 82
REMOVAL 7B— 83
PRECAUTION 7B— 83
DISASSEMBLY 7B— 88
DISASSEMBLY-STEP 1 7B— 88
DISASSEMBLY-STEP 2 7B— 94
DISASSEMBLY-STEP 3 7B— 99
DISASSEMBLY-STEP 4 7B—103
INSPECTION AND REPAIR 7B—107
PRECAUTION 7B—107
TORQUE CONVERTER 7B—107
OIL PUMP 7B—108
CLUTCH ASSEMBLY 7B—113
SMALL SUN GEAR AND
ONE-WAY CLUTCH 7B—122
ONE-WAY CLUTCH AND
CARRIER HUB ASSEMBLY 7B-126
3-4 CLUTCH 7B—128
2-3 ACCUMULATOR 7B—132
GOVERNOR ASSEMBLY
(G4A-HL) 7B-133
LOW AND REVERSE BRAKE 7B—134
2-4 BRAKE BAND 7B—135
BAND SERVO 7B—135
OTHER INSPECTION 7B—135
CONTROL VALVE BODY
(G4A-EL) 7B-136
CONTROL VALVE BODY
(G4A-HL) 7B-155
DIFFERENTIAL 7B—177
OUTPUT GEAR 7B—181
IDLE GEAR 7B—182
BEARING COVER ASSEMBLY 7B—185
BEARING HOUSING 7B—186
ASSEMBLY 7B-187
PRECATION 7B—187
ASSEMBLY-STEP 1 7B—187
ASSEMBLY-STEP 2 7B—197
ASSEMBLY-STEP 3 7B—202
ASSEMBLY-STEP 4 7B—208
INSTALLATION 7B—215
TORQUE SPECIFICATIONS 7B—215
HYDRAULIC CIRCUIT (G4A-EL) 7B—221
HYDRAULIC CIRCUIT (G4A-HL) 7B—239
76G07B-001

7B OUTLINE
G4A-HL
1. OD OFF indicator light
2. OD OFF switch
3. Kick-down switch
4. Cruise control unit
5. Cruise control switch
6. Water temperature switch
7. Inhibitor switch
8. OD release solenoid valve
9. Automatic transaxle
76G07B-004
7B—4

7B OUTLINE
Transaxle Case
To governor valve
/and 2-3 accumulator
Inlet to control valve body
(governor pressure)
Outlet to torque converter
(Release side)
Outlet to torque converter
(Apply side)
Outlet to 3-4 clutch
To governor valve and 2-3 accumulator^
From governor valve (governor pressure)
To torque converter (Release side)
To torque converter (Apply side)
To 3-4 clutch
From oil pump
(To control valve body)
°Lto coasting clutch
y
To reverse clutch
To forward clutch
To low and reverse brake
To 2-4 brake apply side
CgEfey a —* To 2-4 brake release side
7B—10
76G07B-009

OUTLINE 7B
Transaxle Case
Inlet to control valve body
Outlet coasting clutch
Outlet to reverse clutch
Outlet to forward clutch
Oil Pump
Outlet to oil pump
Outlet for lubrication
Outlet to forward clutch
Inlet to oil pump^
Outlet to reverse clutch
Outlet to coasting clutch
Outlet to control valve body
Inlet for lubrication
Inlet to forward clutch Inlet to coasting clutch
Inlet to reverse clutch
76G07B-010
76G07B-011
7B—11

7B TROUBLESHOOTING (G4A-EL)

ON VEHICLE-
-f-
—OFF VEHICLE

\ Inspection point
and

\ reference page

Condition
•

Electronic control system Prelim-
inary
Hydraulic
control
system
Power train \ Inspection point
and

\ reference page

Condition
•
7B-66

m CO I m r--
7B-63

i
cn to I m
Section

4B

|

Section

4B

|

ID to i m
CO CO 1 CD
7B-68
|
en CO 1 IX)
to 1 00 r-.
cn CD 1 CO
7B-69
|

1 CD r--
<N
i no
cn s-1 m
Section
4B

r*-cn
S-1 CD h-
"=1-
rJ CO
7 CD r-
(XI o
1 m
cn CM 1 CD
7B-107

|
CD
7 CD 7 m
I
7B-113
I
CO CM
7 CO r-.
m cn
7 CO r-.
cn
7 DO r-
CM CM
7 CO

|
7B-126

<o cn
7 00 r-
CO <M
7 cn
1*-r*-
7 m r-
\ Inspection point
and

\ reference page

Condition
•
Brake

light
switch

|

Inhibitor

switch

|

Mode

switch

|

1
CO. •o o X
Idle

switch

Throttle

sensor

|

Water

temp,

switch

|
0 tn c 0) cn
s
ffi
Q tn 01 o Hi >
Pulse

generator

|

"a o c 0) a to CM
TJ O CL ID s CO C\l 3-4

solenoid

|

Lock-up
solenoid

I

ATF

level
and
condition

|

Selector

lever

m Xj CO CJ 03
1 sz
Idle
speed
and
Ignition
timing

Control

valves

Accumulators
Oil
pump
Hydraulic

circuit

Torque

converter

Forward

clutch
Coasting
clutch

Reverse

clutch
JT O
u TT ro 2-4

brake
band
and

servo
$ 2
B cn cii > £ "O C CO
o
XI y
o >. CO S cb a O
One-way

clutch

2

s CI Cn tz JC 5 0-
Planetary

gear

Differential

assembly
Accelerating

Vehicle does
not
move
in
D,
S,
L,
or R
range
O O O O O O O O O O 0

Accelerating

Vehicle moves
in N
range -0 0 -—

Accelerating
Excessive creep
-0 O O -—

Accelerating
No creep
at all
O o o o
o
G 0 O O

Shifting

|

No shift
O O o
o
0 O 0 0
o
o O

Shifting

|
Abnormal shift sequence
0 o O O 0
o
o 0 O o o 0 O

Shifting

|
Frequent shifting 0 o 0 0 o 0 O O 0

Shifting

|

Excessively high
or
low
shift point 0 o 0 O 0 0 o 0 O 0 0
Shifting

|

No lock-up
0 o 0 0 o 0 O O o O

Shifting

|

No kick-down o o o o

Slipping

Engine
run
away
or
slip when
starting vehicle 0 o 0 O o O

Slipping
Engine
run
away
or
slip when
up-
or
down-shifting o o o 0 o O 0 0 O
8 n cn 4S SI V)
Excessive
N to D or N to R

shift shock o O o o o O
8 n cn 4S SI V)
Excessive shift shock when
up-

shifting
or
downshifting o o o o 0 0 0 8 n cn 4S SI V) Excessive shift shock when
changing range 0 0 o 0 o

j
Noise

Transaxle noisy
in N or P

range o o 0 O

j
Noise

Transaxle noisy
in D, S, L,
or

R range o 0 0 O

I
Others

j

No engine braking o O o 0 o o

I
Others

j

No mode change o 0 o o o o o o o
O
o
0

I
Others

j
Transaxle overheats
o o
0 o 0 o 0

I
Others

j
Vehicle moves
in
"P",
or
park-ing gear
not

disengaged when
"P"
is
dis-
engaged
0 O

I
Others

j

Hold indicator flashes o
0
o
0
o
O
o — — —
I
Others

j

Engine will
not
start
o
o
O — — —
76G07B-014
7B—14

7B TROUBLESHOOTING (G4A-EL)
STEP 2 (PRELIMINARY INSPECTION)
In this step, the fundamental points related to the automatic transaxle are checked. These points must
be kept in the correct condition at all times in order to assure proper operation of the automatic transaxle.
1. Automatic Transmission Fluid (ATF)
Check ATF level and condition. (Refer to page 7B—71)
2. Selector Lever
Check selector lever position and adjust if necessary. (Refer to page 7B—72)
76G07B-022
3. Throttle cable
(1) Check the inner and outer cable for damage.
(2) Make sure that the accelerator operates
smoothly.
76G07B-023
4. Idle Speed
Check idle speed. (Refer to Section 4B)
5. Tire Inflation Pressure
Check tire inflation pressure. (Refer to Section 12)
76G07B-024
6. Inhibitor Switch
Check the inhibitor switch for operation. (Refer to
page 7B—65)
76G07B-025
7B-22

TROUBLESHOOTING (G4A-EL) 7B
7. Oil Leakage
Check for oil leakage.
(1) Warm up the ATF.
(2) Apply the parking brake and block the wheels
to prevent the vehicle from rolling.
(3) Shift the selector lever to R range.
(4) Check if oil leaks from the following oil seals
or gaskets.
(5) If oil leaks, replace the oil seal or gasket.
76G07B-026
Check for fluid leaks; the following figure shows the locations where fluid leakage may possibly occur.
1. Oil pan
2. Control valve body cover
3. Oil pump
4. Inhibitor switch
5. Speedometer driven gear
6. Pulse generator
7. Oil filler tube
8. Throttle cable
9. Bearing cover
10. Driveshaft
11. Square head plug
12. Transaxle case
13. Drain plug
14. Oil cooler return pipe
15. Oil cooler outlet pipe
16. Fluid temperature switch
17. Blind plugs
76G07B-027
7B—23