sensor MAZDA CX9 2023 Owner's Manual

ï‚·The hands-free liftgate sensor may not
operate normally under the following
conditions.
ï‚·Your foot remains placed within the
detection area.
ï‚·You move your foot left and right
within the detection area.
ï‚·The kicking motion is too fast or too
slow.
ï‚·Your foot contacts the rear bumper
when doing the kicking motion.
ï‚·You are wearing shoes such as rubber
boots which do not conduct electricity
well.
ï‚·There is equipment emitting strong
radio waves near the vehicle.
ï‚·The detection area of the hands-free
liftgate sensor is dirty.
ï‚·When the detection area of the
hands-free liftgate sensor is dirty, wipe
it off with a clean cloth. Place the
transmitter outside of its operation
range or wipe off the area around the
sensor with a clean cloth after turning
off the hands-free liftgate using the
Mazda Connect.
ï‚·If the operation using the hands-free
liftgate sensor is not possible even
though the operation conditions are met,
consult an Authorized Mazda Dealer.
Hands-free liftgate ON/OFF switching
The hands-free liftgate can be switched
on/off.
To prevent an unintended operation, turn
off the function.
Refer to the Settings section in the Mazda
Connect Owner's Manual.
Changing the power liftgate fully open
position
The power liftgate fully-open position can
be changed according to the height of a
garage.
When changing the position
1. Stop the liftgate at the desired position.
2. Press the power liftgate close switch for about three seconds.
A beep sound is activated two times to
indicate that the position change has
been completed.
NOTE
Set the desired fully-open position of the
liftgate at the position where it is open
more than halfway. The position where it
is less than halfway open cannot be set.
To reset
1. Open the liftgate.
2. Press the power liftgate close switchfor about seven seconds.
A beep sound is activated three times
to indicated that the reset has been
completed.
NOTE
After about 3 seconds have elapsed since
the switch was pressed, a beep sound is
activated 2 times to indicate that the
liftgate fully-open position has changed.
Continuously press the switch for about 7
seconds to complete the reset.
Jam-safe equipment
While the power liftgate is opening/
closing electrically and the system detects
a person or an object in the liftgate's path,
the liftgate will move in the reverse
direction automatically and stops.
Before Driving
Doors and Locks
3-25
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

WA R N I N G
Always check the area around the power
liftgate before opening/closing it:
Not checking for occupants and objects
around the power liftgate before opening/
closing it is dangerous. The jam-safe
equipment is designed to prevent jamming
in the event an obstruction is in the
liftgate's path. The system may not detect
certain objects obstructing the liftgate
depending on the way they are positioned
and their shape. However, if the jam-safe
function detects an obstruction and moves
the liftgate in the reverse direction, an
occupant in the liftgate's path could be
seriously injured.
CAUTION
Sensors are installed on both ends of the
power liftgate. Be careful not to allow the
sensors to be scratched or damaged by
sharp objects, otherwise the liftgate may
no longer open/close automatically. In
addition, if the sensor is damaged while the
liftgate is closing automatically, the system
will stop.
Sensor
NOTE
The jam-safe equipment does not activate
during easy closure operation when the
power liftgate is between the near-shut
position and fully closed position.
When the power liftgate is moving in the
open/close direction and an obstruction is
detected, the beep sound will be heard and
the liftgate moves in the reverse direction
and stops.
Liftgate easy closure
The Easy Closure s ystem automatically
closes the liftgate completely from the
near-shut position.
This system also operates when the liftgate
is closed manually.
WA R N I N G
When closing a liftgate, always keep hands
and fingers away from the liftgate:
Placing hands or fingers around a liftgate is
dangerous because the liftgate closes
automatically from the near-shut position,
which could cause hands and fingers to be
pinched and injured.
NOTE
ï‚·If the electric liftgate opener is pressed
while the easy closure function is
operating, the liftgate can be opened.
ï‚·If the liftgate is opened/closed
repeatedly in a short period of time, the
easy closure function may not operate.
Wait for about 2 seconds and then try
again.
Before Driving
Doors and Locks
3-26
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

Fuel and Engine Exhaust Precautions
â–¼Fuel Requirements
Vehicles with catalytic converters or oxygen sensors must use O
NLY UNLEADED FUEL,
which will reduce exhaust emissions and keep spark plug fouling to a minimum.

To achieve maximum engine performance, use the specified fuel.
Fuel Octane Rating*1 (Anti-knock index)
Regular unleaded fuel 87 [(R+M)/2 method] or above (91 RON or ab ove)
*1 U.S. federal law requires that octane ratings be posted on gas station pumps.
Fuel with a rating lower than 87 octane (91 RON) will negatively affect the emission control
system performance and could also cause engine knocking and ser ious engine damage.
CAUTION
USE ONLY UNLEADED FUEL.
Leaded fuel is harmful to the catalytic co nverter and oxygen sensors and will lead to
deterioration of the emission control system and or failures.
 This vehicle can only use oxygenated fuels containing no more than 10 % ethanol by
volume. Damage to the vehicle may occur when ethanol exceeds this recommendation, or
if the gasoline contains any methanol. Stop us ing gasohol of any kind if your vehicle engine
is performing poorly.
 Never add fuel system additives other than a Mazda genuine product, otherwise the
emission control system could be damaged. Consult an Authorized Mazda Dealer for
details.
Gasoline blended with oxygenates such as alcohol or ether compo unds are generally
referred to as oxygenated fuels. The common gasoline blend that can be used with your
vehicle is ethanol blended at no more than 10 %. Gasoline conta ining alcohol, such as
ethanol or methanol, may be marketed under the name "Gasohol".

Vehicle damage and drivability problems resulting from the use of the following may not be
covered by the warranty.
ï‚·Gasohol containing mo re than 10 % ethanol.
ï‚·Gasoline or gasohol containing methanol.
ï‚·Leaded fuel or leaded gasohol.
Before Driving
Fuel and Emission
3-27
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

Reducing glare from headlights
Manual day/night mirror
Push the day/night lever forward for day
driving. Pull it back to reduce glare of
headlights from vehicles at the rear.

Day/Night lever
Day
Night
Auto-dimming mirror
The auto-dimming m irror automatically
reduces the glare of headlights from
vehicles at the rear when the ignition is
switched ON.

(With Homelink wireless control
system)
(Type A)
Press the OFF button (
) to cancel the
auto-dimming function . The indicator light
will turn off.
To reactivate the auto-dimming function,
press the ON button (
). The indicator
light will illuminate.
Indicator lightOFF b utton
ON button

(Type B)
Press the ON/OFF button (
) to cancel the
auto-dimming function. The indicator light
will turn off.
To reactivate the auto -dimming function,
press the ON/OFF button (
). The
indicator light will illuminate.
Indicator light
ON/OFF button
(Without Homelink wireless control
system)
Press the ON/OFF button
to cancel the
auto-dimming function. The indicator light
will turn off.
To reactivate the auto -dimming function,
press the ON/OFF button
. The indicator
light will illuminate.

ON/OFF b utton
Indicator light
NOTE
ï‚·Do not use glass cleaner or suspend
objects on or around the light sensor.
Otherwise, light sensor sensitivity will
be affected and may not operate
normally.
Before Driving
Mirrors
3-35
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

(With Homelink wireless control
system)
(Type A)
Light sensor
(Type B)
Light sensor
(Without Homelink wireless control
system)

Light sensor
ï‚·(With Homelink wireless control
system)
For information regarding the 3 buttons
(Type A
,,/Type B , , )
on the auto-dimming mirror.
Refer to HomeLink Wireless Control
System on page 4-85.
ï‚·The auto-dimming function is canceled
when the ignition is switched ON and
the shift lever is in reverse (R).
Before Driving
Mirrors
3-36
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

i-ACTIVSENSE............................. 4-116i-ACTIVSENSE
*...................... 4-116
Adaptive Front Lighting System
(AFS)
*.......................................4-119
High Beam Control System
(HBC)
*......................................4-120
Blind Spot Monitoring (BSM)
*.........
.................................................. 4-123
Traffic Sign Recognition System
(TSR)
*...................................... 4-129
Distance Recognition Support
System (DRSS)
*....................... 4-135
Driver Attenti on Alert (DAA)
*..........
.................................................. 4-139
Rear Cross Traffic Alert (RCTA)
*.....
.................................................. 4-141
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function)
*............... 4-145
Lane-keep Assist System (LAS) &
Lane Departure Warning System
(LDWS)
*.................................. 4-160
Advanced Smart City Brake Support
(Advanced SCBS)
*...................4-171
Smart City Brake Support [Forward]
(SCBS F)
*.................................4-174
Smart City Brake Support [Reverse]
(SCBS R)
*................................ 4-178
Smart Brake Support (SBS)
*.... 4-182
360° View Monitor (Mazda Connect
(Type A))
*................................ 4-184
360° View Monitor (Mazda Connect
(Type B))
*................................. 4-211
Forward Sensing Camera (FSC)
*......
.................................................. 4-239
Radar Sensor (Front)*.............. 4-244
Radar Sensors (Rear)
*.............. 4-247
Ultrasonic Sensor (Rear)
*.........4-249
Front Camera/Side Cameras/Rear
Camera
*.................................... 4-250
Cruise Control............................... 4-251 Cruise Control
*.........................4-251
Tire Pressure Monitoring
System.............................................4-256 Tire Pressure Monitoring
System...................................... 4-256
Rear View Monitor (Mazda Connect
(Type A))........................................ 4-260 Rear View Monitor (Mazda Connect
(Type A))
*................................ 4-260
Rear View Monitor (Mazda Connect
(Type B)).........................................4-268 Rear View Monitor (Mazda Connect
(Type B))
*.................................4-268
Parking Sensor System (Mazda
Connect (Type A))......................... 4-276 Parking Sensor System (Mazda
Connect (Type A))
*.................. 4-276
Parking Sensor System (Mazda
Connect (Type B))......................... 4-287 Parking Sensor System (Mazda
Connect (Type B))
*.................. 4-287
4-2*Some models.
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

CAUTION
If the engine coolant temperature gauge
needle is in the red range, there is the
possibility of overheating. Drive slowly to
reduce engine load until you can find a safe
place to stop the vehicle and wait for the
engine to cool down.
Refer to Overheating on page 7-23.
NOTE
ï‚·If the engine coolant temperature is high
or the engine is hot, the engine output
may be limited.
â–¼Fuel Gauge
The fuel gauge shows approximately how
much fuel is remaining in the tank when
the ignition is switched ON. We
recommend keeping the tank over 1/4 full.

Full
1/4 Full
Empty
If the low fuel warni
ng light illuminates or
the fuel level is very low, refuel as soon as
possible.
If inconsistency in engine performance or
stalling occurs due to low fuel level
conditions, refuel the vehicle as soon as
possible and add at least 10 L (2.7 US gal,
2.2 Imp gal) of fuel.
Refer to Taking Action on page 7-37.
NOTE
ï‚·After refueling, it may require some time
for the indicator to stabilize. In addition,
the indicator may deviate while driving
on a slope or curve since the fuel moves
in the tank.
ï‚·The direction of the arrow () indicates
that the fuel-filler lid is on the left side
of the vehicle.
â–¼ Dashboard Illumination
When the lights are
turned on with the
ignition switched ON, the brightness of
the dashboard illumination is dimmed.
However, when the light sensor detects
that the surrounding area is bright such as
when the lights are turned on in the
daytime, the dashboard illumination does
not dim.
NOTE
ï‚·When the ignition is switched ON in the
early evening or at dusk, the dashboard
illumination is dimmed for several
seconds until the light sensor detects the
brightness of the surrounding area,
however, the dimming may cancel after
the brightness is detected.
ï‚·When the lights are turned on, the
lights-on indicator light in the
instrument cluster turns on.
Refer to Headlights on page 4-71.
When Driving
Instrument Cluster and Display
4-17
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

ï‚·The direction of the arrow () indicates
that the fuel-filler lid is on the left side
of the vehicle.
â–¼ Dashboard Illumination
(Without auto-light control)
When the lights are turned on with the
ignition switched ON, the brightness of
the dashboard illumination is dimmed.
(With auto-light control)
When the lights are turned on with the
ignition switched ON, the brightness of
the dashboard illumination is dimmed.
However, when the light sensor detects
that the surrounding area is bright such as
when the lights are turned on in the
daytime, the dashboard illumination does
not dim.
NOTE
ï‚·(With auto-lig
ht control)
When the ignition is switched ON in the
early evening or at dusk, the dashboard
illumination is dimmed for several
seconds until the light sensor detects the
brightness of the surrounding area,
however, the dimming may cancel after
the brightness is detected.
ï‚·When the lights are turned on, the
lights-on indicator light in the
instrument cluster turns on.
Refer to Headlights on page 4-71.
The brightness of the instrument cluster
and dashboard illuminations can be
adjusted by rotating the knob.
ï‚·The brightness decreases by rotating the
knob to the left. A beep sound will be
heard when the knob has been rotated to
the maximum dim position.
ï‚·The brightness increases by rotating the
knob to the right.
Dim
Bright
Function for canceling illumination
dimmer
The illumination dimmer can be canceled
by rotating the dashboard illumination
knob to the right until a beep sound is
heard while the instrument cluster is
dimmed with the ignition switched ON. If
the instrument cluster's visibility is
reduced due to glare from surrounding
brightness, cancel the illumination
dimmer.
NOTE
ï‚·The illumination dimmer can be
canceled by pressing the dashboard
illumination knob.
ï‚·When the illumination dimmer is
canceled, the instrument cluster cannot
be dimmed even if the lights are turned
on.
ï‚·When the illumination dimmer is
canceled, the screen in the center
display switches to constant display of
the daytime screen.
When Driving
Instrument Cluster and Display
4-34
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

ï‚·The temperature unit (Centigrade/
Fahrenheit) of the engine coolant gauge
display changes in conjunction with the
temperature unit of the outside
temperature display.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
â–¼Fuel Gauge
The fuel gauge shows approximately how
much fuel is remaining in the tank when
the ignition is
switched ON. We
recommend keeping the tank over 1/4 full.

Full
1/4 Full
Empty
If the low fuel warnin g light illuminates or
the fuel level is very low, refuel as soon as
possible.
If inconsistency in engine performance or
stalling occurs due to low fuel level
conditions, refuel the vehicle as soon as
possible and add at least 10 L (2.7 US gal,
2.2 Imp gal) of fuel.
Refer to Taking Action on page 7-37.
NOTE
ï‚·After refueling, it may require some time
for the indicator to st abilize. In addition,
the indicator may deviate while driving
on a slope or curve since the fuel moves
in the tank.
ï‚·The display indicating a quarter or less
remaining fuel has more segments to
show the remaining fu el level in greater
detail.
ï‚·The direction of the arrow () indicates
that the fuel-filler lid is on the left side
of the vehicle.
â–¼ Dashboard Illumination
(Without auto-light control)
When the lights are turned on with the
ignition switched ON
, the brightness of
the dashboard illumination is dimmed.
(With auto-light control)
When the lights are turned on with the
ignition switched ON , the brightness of
the dashboard illumination is dimmed.
However, when the li ght sensor detects
that the surrounding area is bright such as
when the lights are turned on in the
daytime, the dashboard illumination does
not dim.
NOTE
ï‚·(With auto-light control)
When the ignition is switched ON in the
early evening or at dusk, the dashboard
illumination is dimmed for several
seconds until the light sensor detects the
brightness of the surrounding area,
however, the dimming may cancel after
the brightness is detected.
ï‚·When the lights are turned on, the
lights-on indicator light in the
instrument cluster turns on.
When Driving
Instrument Cluster and Display
4-48
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08

Active Driving Display*
Optical receiverDust-proof sheet
WA R N I N G
Always adjust the display brightness and position with the vehicle stopped:
Adjusting the display brightness and position wh ile driving the vehicle is dangerous as doing
so could distract your attention from the road ahead and lead to an accident.
CAUTION
 Do not place beverages near the active driving display. If water or other liquids are splashed
on the active driving displa y, it could cause damage.
 Do not place objects above the active driving display or apply stickers to the dust-proof
sheet/optical receiver as they will cause interference.
 A sensor is integrated to control the display's luminosity. If the optical receiver is covered,
the display's luminosity will lower making the display
difficult to view.
 Do not allow intense light to hit the optical receiver. Otherwise, it could cause damage.
NOTE
ï‚·Wearing polarized sunglasses will reduce the visibility of the active driving display due to
the characteristics of the display.
ï‚·If the battery has been removed and re-installed or the battery voltage is low, the adjusted
position may deviate.
ï‚·The display may be difficult to view or temporarily affected by weather conditions such as
rain, snow, light, and temperature.
ï‚·If the audio system is removed, the active driving display cannot be operated.
The active driving display indicates the following information:
ï‚·Blind Spot Monitoring (BSM) Ope ration Conditions and Warnings
When Driving
Instrument Cluster and Display
*Some models.4-57
CX-9_8LJ2-EA-22H_Edition1_old 2022-6-9 13:33:08