engine MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)

6–66
Maintenance and Care
Owner Maintenance
3. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it is
blown.
NormalBlown
5. Insert a new fuse of the same amperage
rating, and make sure it fi ts tightly. If
it does not fi t tightly, have an expert
install it. We recommend an Authorised
Mazda Repairer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage the
electric system.
6. Reinstall the cover and make sure that
it is securely installed.
Replacing the fuses under the bonnet
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the bonnet. If a fuse is blown,
it must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–68
Maintenance and Care
Owner Maintenance
Fuse Panel Description
Fuse block (Engine compartment)
Multiplex slow blow fuse
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 FOG 15 A Front fog lights
*
2 H/L HI 20 A Headlight high beam
3 H/CLEAN 20 A Headlight washer *
4 STOP 10 A Brake lights, Rear fog light *
5 ROOM 15 A Overhead light
6
7.5 A Engine control system *
7 FUEL WARM 15 A Fuel warmer *
8 HAZARD 25 A Hazard warning fl ashers, Direction indicator lights
9 ABS/DSCS 30 A ABS, Dynamic stability control system *
10 METER2 7.5 A Instrument cluster *
11 AUDIO2 7.5 A Audio system *
12 BOSE 25 A Bose ® Sound System-equipped model *
13 AUDIO1 15 A Audio system *
14 FUEL PUMP 15 A Fuel system *
15 HID R
D R L 15 A Headlight (RH) *1
16 AT PUMP 15 A Transaxle control system *
17 HORN 15 A Horn
18 TAIL 15 A Tail lights, Number plate lights, Position lights
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–69
Maintenance and Care
Owner Maintenance
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
19 CNG 15 A —
20 AT 15 A Transaxle control system
21 R.WIPER 15 A Rear window wiper
*
22 A/C 7.5 A Air conditioner
23 ENGINE3 15 A Engine control system
24 ENGINE2 15 A Engine control system
25 ENGINE1 15 A Engine control system
26 GLOW SIG 5 A Engine control system
*
27 EVVT 20 A Engine control system *
28 WIPER 20 A Front window wiper and washer
29 DCDC REG 30 A For protection of various circuits *
30 FUEL PUMP2 30 A —
31 ADD FAN DE 40 A Cooling fan *
32 P.WINDOW1 30 A Power windows
33 H/L LOW R 15 A Headlight low beam (RH) *2
34 H/L LOW L
HID L 15 A Headlight (LH) *1 , Headlight low beam (LH) *2
35 METER1 10 A Instrument cluster
36 IG2 30 A For protection of various circuits
37 LPG 30 A —
38 FAN DE 40 A Cooling fan
*
39 DCDC DE 40 A For protection of various circuits *
40 SRS1 7.5 A Air bag
41 ENGINE. IG1 15 A Engine control system
42 C/U IG1 15 A For protection of various circuits
43 — — —
*1 With xenon fusion headlights
*2 With halogen headlights
.B[EB@&'&&"@&EJUJPOJOEC







6–73
Maintenance and Care
Appearance Care
Maintaining the Finish
Washing
CAUTION
  When the wiper lever is in the
position and the ignition is switched
ON, the wipers may move
automatically in the following cases:
 


 If the windscreen above the rain
sensor is touched or wiped with a
cloth.
 


 If the windscreen is struck with a
hand or other object from either
outside or inside the vehicle.
  Keep hands and scrapers clear of the
windscreen when the wiper lever is
in the
position and the ignition
is switched ON as fi ngers could be
pinched or the wipers and wiper
blades damaged when the wipers
activate automatically.
 If you are going to clean the
windscreen, be sure the wipers are
turned off completely (when it is
most likely that the engine is left
running) this is particularly important
when clearing ice and snow.
 
 Do not spray water in the engine
compartment. Otherwise, it could
result in engine-starting problems or
damage to electrical parts.
  When washing and waxing the
vehicle, be careful not to apply
excessive force to any single area
of the vehicle roof or the aerial.
Otherwise, you could dent the
vehicle or damage the aerial. To help protect the fi nish from rust
and deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface when:
 


 The vehicle is washed without fi rst
rinsing off dirt and other foreign matter.
 


 The vehicle is washed with a rough, dry,
or dirty cloth.
 


 The vehicle is washed at a car wash that
uses brushes that are dirty or too stiff.
 


 Cleansers or wax containing abrasives
are used.
NOTE
  Mazda is not responsible for
scratches caused by automatic car
washes or improper washing.
  Scratches are more noticeable on
vehicles with darker paint fi nishes.
To minimize scratches on the vehicle's
paint fi nish:




 Rinse off any dirt or other foreign matter
using lukewarm or cold water before
washing.
 


 Use plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
 


 Rub gently when washing or drying the
vehicle.
 


 Take your vehicle only to a car wash
that keeps its brushes well maintained.
 


 Do not use abrasive cleansers or wax
that contain abrasives.
.B[EB@&'&&"@&EJUJPOJOEC







6–77
Maintenance and Care
Appearance Care
Plastic Part Maintenance
 












 When cleaning the plastic lenses of
the lights, do not use petrol, paraffi n,
rectifi ed spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolour or damage the
surfaces resulting in a signifi cant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, fl ush with water
immediately.
 


 If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fl uids such as petrol,
oil, engine coolant, or battery fl uid, it
could cause discolouration, staining,
or paint peeling. Wipe off any such
chemical agents or fl uids using a soft
cloth immediately.
 


 High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
 


 Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
 


 In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result
in deformation of plastic parts or paint
damage.
Interior Care
WARNING
Do not spray water in the cabin:
Splashing water on electrical parts
such as the audio unit and switches
is dangerous as it could cause a
malfunction or a fi re.
Instrument panel Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
instrument panel. They will damage and
discolour the instrument panel. If these
solutions get on the instrument panel, wipe
them off immediately.
CAUTION
Do not use glazing agents.
Glazing agents contain ingredients
which may cause discolouration,
wrinkling, cracks and peeling.
Instrument panel top (soft pad)
 




 Extremely soft material is used for the
soft pad surface. When cleaning, it is
recommended that you use a clean towel
dampened in a mild detergent to remove
soiling.
 


 If the soft pad surface is rubbed harshly,
it could result in the surface being
damaged leaving white scratch marks.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–1
7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.



Parking in an Emergency ................... 7-2
Parking in an Emergency ............... 7-2
Roadside Emergency Triangle
Retaining Strap
* ............................. 7-2
Flat Tyre ............................................... 7-3
Spare Tyre and Tool Storage .......... 7-3
Emergency Flat Tyre Repair Kit* ........ 7-8
Changing a Flat Tyre (With spare
tyre) .............................................. 7-15
Battery Runs Out .............................. 7-21
Jump-Starting ............................... 7-21
Emergency Starting .......................... 7-24
Starting a Flooded Engine (MZR 1.6,
SKYACTIV-G 1.5 and SKYACTIV-G
2.0) ............................................... 7-24
Push-Starting ................................ 7-24
Running Out of Fuel (SKYACTIV-D
2.2) ............................................... 7-25
Overheating ....................................... 7-26
Overheating .................................. 7-26
Emergency Towing ............................ 7-28
Towing Description ...................... 7-28
Towing Hooks .............................. 7-29 Warning/Indicator Lights and Warning
Sounds ................................................ 7-32
If a Warning Light Turns On or
Flashes .......................................... 7-32
Message Indicated in Multi-
information Display ..................... 7-45
Message Indicated on Display* ...... 7-47
Warning Sound is Activated ......... 7-49
When Liftgate/Boot Lid Cannot be
Opened ............................................... 7-54
When Liftgate/Boot Lid Cannot be
Opened ......................................... 7-54
Active Driving Display Does Not
Operate ............................................... 7-56
If the Active Driving Display does not
operate .......................................... 7-56
.B[EB@&'&&"@&EJUJPOJOEC







7–9
If Trouble Arises
Flat Tyre
NOTE
  The tyre sealant cannot be reused.
Purchase new tyre sealant at an
Authorised Mazda Repairer.
  The emergency fl at tyre repair kit
cannot be used in the following
cases.
 Consult an expert repairer, we
recommend an Authorised Mazda
Repairer.
 


 The period of effective use for
the tyre sealant has expired. (The
period of effectiveness is indicated
on the bottle label.)
 


 The tear or puncture exceeds about
4 mm (0.16 in).
 


 The damage has occurred to an
area of the tyre other than the
tread.
 


 The vehicle has been driven with
nearly no air remaining in the tyre.
 


 The tyre has come off the wheel
rim.
 


 Damage to the wheel rim has
occurred.
 


 The tyre has two or more
punctures.
Using the Puncture Tyre Repair
Kit
1. Move the vehicle off the right-of-way
to a safe place on a level and hard
surface where the vehicle does not
obstruct traffi c.
2. Shift the shift lever to the 1 or Reverse
(R) position for a manual transaxle, and
shift the selector lever to the P position
for an automatic transaxle.
3. Apply the parking brake with the brake
pedal depressed and turn off the engine.
4. If necessary, fl ash the hazard warning
lights and set up the roadside
emergency triangle.
5. Unload passengers and cargo and
remove the puncture tyre repair kit.
Saloon
Hatchback
.B[EB@&'&&"@&EJUJPOJOEC







7–15
If Trouble Arises
Flat Tyre
Changing a Flat Tyre
(With spare tyre)
NOTE
If the following occurs while driving, it
could indicate a fl at tyre.


 Steering becomes diffi cult. 
 The vehicle begins to vibrate
excessively.
  The vehicle pulls in one direction.

If you have a fl at tyre, drive slowly to a
level spot that is well off the road and out
of the way of traffi c to change the tyre.
Stopping in traffi c or on the shoulder of a
busy road is dangerous.
WARNING
Be sure to follow the directions for
changing a tyre:
Changing a tyre is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure someone.
No person should place any portion
of their body under a vehicle that is
supported by a jack.
Never allow anyone inside a vehicle
supported by a jack:
Allowing someone to remain in
a vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.
NOTE
Make sure the jack is well lubricated
before using it.
1. Park on a level surface off the right-of-
way and fi rmly set the parking brake.
2. Put a vehicle with an automatic
transaxle in Park (P), a manual
transaxle in Reverse (R) or 1, and turn
off the engine.
3. Turn on the hazard warning fl asher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffi c.
5. Remove the jack, tool, and spare tyre
(page 7-3 ).
6. Block the wheel diagonally opposite
the fl at tyre. When blocking a wheel,
place a tyre block both in front and
behind the tyre.
NOTE
When blocking a tyre, use rocks or
wood blocks of suffi cient size if possible
to hold the tyre in place.
.B[EB@&'&&"@&EJUJPOJOEC







7–18
If Trouble Arises
Flat Tyre
8. Turn the jack handle clockwise and
raise the vehicle high enough so that
the spare tyre can be installed. Before
removing the wheel nuts, make sure
your Mazda is fi rmly in position and
that it cannot slip or move.
WARNING
Do not jack up the vehicle higher than
is necessary:
Jacking up the vehicle higher than
is necessary is dangerous as it could
destabilize the vehicle resulting in an
accident.
Do not start the engine or shake the
vehicle while it is jacked up:
Starting the engine or shaking
the vehicle while it is jacked up is
dangerous as it could cause the vehicle
to fall off the jack resulting in an
accident.
Never go under the vehicle while it is
jacked up:
Going under the vehicle while it is
jacked up is dangerous as it could
result in death or serious injury if the
vehicle were to fall off the jack. 9. Remove the wheel nuts by turning
them anticlockwise; then remove the
wheel and centre cap.
Mounting the Spare Tyre
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.
WARNING
Make sure the mounting surfaces of
the wheel, hub and wheel nuts are
clean before changing or replacing
tyres:
When changing or replacing a tyre,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The wheel
nuts could loosen while driving and
cause the tyre to come off, resulting in
an accident.
.B[EB@&'&&"@&EJUJPOJOEC







7–21
If Trouble Arises
Battery Runs Out
Jump-Starting
Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If you
feel unsure about jump-starting, we strongly recommend that you have a competent service
technician do the work.
WARNING
Follow These Precautions Carefully:
To ensure safe and correct handling of the battery, read the following precautions
carefully before using the battery or inspecting it.
Do not allow the positive ( ) terminal to contact any other metal object that
could cause sparks:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. When working near a battery,
do not allow metal tools to contact the positive (
) or negative () terminal of the
battery.
Keep all fl ames, including cigarettes, and sparks away from open battery cells:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries.
Do not jump-start a frozen battery or one with a low fl uid level:
Jump-starting a frozen battery or one with a low fl uid level is dangerous. It may rupture
or explode, causing serious injury.
Connect the negative lead to a good ground point away from the battery:
Connecting the end of the second jumper lead to the negative (
) terminal of the
discharged battery is dangerous.
A spark could cause the gas around the battery to explode and injure someone.
Route the jumper leads away from parts that will be moving:
Connecting a jumper lead near or to moving parts (cooling fans, belts) is dangerous.
The lead could get caught when the engine starts and cause serious injury.
.B[EB@&'&&"@&EJUJPOJOEC