MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)

6–45
Maintenance and Care
Owner Maintenance
CAUTION
  Be careful not to allow the rubber
ring shown in the fi gure to be
scratched or damaged.
  If the rubber ring detaches, reattach it
before inserting a new battery.
Rubber ring
Ty r e s
For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tyre infl ation pressures and
stay within the recommended load limits
and weight distribution.
WARNING
Using Different Tyre Types:
Driving your vehicle with different
types of tyres is dangerous. It could
cause poor handling and poor braking;
leading to loss of control.
Except for the limited use of the
temporary spare tyre, use only the same
type tyres (radial, bias-belted, bias-type)
on all four wheels.
Using Wrong-Sized Tyres:
Using any other tyre size than what is
specifi ed for the vehicle (page 9-13 )
is dangerous. It could seriously affect
ride, handling, ground clearance,
tyre clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tyres that
are the correct size specifi ed for the
vehicle.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–46
Maintenance and Care
Owner Maintenance
Tyre Infl ation Pressure
WARNING
Always infl ate the tyres to the correct
pressure:
Overinfl ation or underinfl ation of tyres
is dangerous. Adverse handling or
unexpected tyre failure could result in
a serious accident.
Refer to Tyres on page 9-13 .
Use only a Mazda-genuine tyre valve
cap:
Use of a non-genuine part is dangerous
as the correct tyre air pressure cannot
be maintained if the tyre valve becomes
damaged. If the vehicle is driven under
this condition, the tyre air pressure
will decrease which could result in a
serious accident. Do not use any part
for the tyre valve cap that is not a
Mazda-genuine part.
Inspect all tyre pressures monthly
(including the spare
* ) when the tyres are
cold. Maintain recommended pressures for
the best ride, handling, and minimum tyre
wear.
Refer to the specifi cation charts (page
9-13 ).
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-164 .
NOTE

 Always check tyre pressure when
tyres are cold.
  Warm tyres normally exceed
recommended pressures. Do not
release air from warm tyres to adjust
the pressure.
  Underinfl ation can cause reduced
fuel economy, uneven and
accelerated tyre wear, and poor
sealing of the tyre bead, which
will deform the wheel and cause
separation of tyre from rim.
  Overinfl ation can produce a harsh
ride, uneven and accelerated tyre
wear, and a greater possibility of
damage from road hazards.
 Keep your tyre pressure at the correct
levels. If one frequently needs
infl ating, have it inspected.
Tyre Rotation
WARNING
Rotate tyres periodically:
Irregular tyre wear is dangerous. To
equalize tread wear for maintaining
good performance in handling and
braking, rotate the tyres every 10,000
km (6,250 miles), or sooner if irregular
wear develops.
During rotation, inspect them for correct
balance.
.B[EB@&'&&"@&EJUJPOJOEC







6–47
Maintenance and Care
Owner Maintenance
NOTE
(Without temporary spare tyre)
Because your vehicle is not equipped
with a spare tyre, you cannot do a tyre
rotation safely with the jack that comes
with your vehicle. Have an expert
repairer, we recommend an Authorised
Mazda Repairer perform tyre rotation.
Do not include (TEMPORARY USE ONLY)
spare tyre in rotation.Forward
Also, inspect them for uneven wear and
damage. Abnormal wear is usually caused
by one or a combination of the following:
 


 Incorrect tyre pressure



 Improper wheel alignment



 Out-of-balance wheel



 Severe braking
After rotation, infl ate all tyre pressures to
specifi cation (page 9-13 ) and inspect the
wheel nuts for tightness.
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-164 .
CAUTION
Rotate unidirectional tyres and radial
tyres that have an asymmetrical tread
pattern or studs only from front to rear,
not from side to side. Tyre performance
will be reduced if rotated from side to
side.
Replacing a Tyre
WARNING
Always use tyres that are in good
condition:
Driving with worn tyres is dangerous.
Reduced braking, steering, and traction
could result in an accident.
Replace all four tyres at the same time:
Replacing just one tyre is dangerous.
It could cause poor handling and poor
braking resulting in loss of vehicle
control. Mazda strongly recommends
that you replace all four tyres at the
same time.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–48
Maintenance and Care
Owner Maintenance
If a tyre wears evenly, a wear indicator
will appear as a solid band across the
tread.
Replace the tyre when this happens.
New treadTread wear indicator
Worn tread
You should replace the tyre before the
band crosses the entire tread.
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-164 .
Temporary Spare Tyre *
Inspect the temporary spare tyre at least
monthly to make sure it is properly
infl ated and stored.
NOTE
The temporary spare tyre condition
gradually deteriorates even if it has not
been used.
The temporary spare tyre is easier to
handle because of its construction which
is lighter and smaller than a conventional
tyre. This tyre should be used only for an
emergency and only for a short distance. Use the temporary spare tyre only until
the conventional tyre is repaired, which
should be as soon as possible.
Refer to Tyre on page 9-13 .
CAUTION
  Do not use your temporary spare
tyre rim with a snow tyre or a
conventional tyre. Neither will
properly fi t and could damage both
tyre and rim.
  The temporary spare tyre has a tread
life of less than 5,000 km (3,000
miles). The tread life may be shorter
depending on driving conditions.
  The temporary spare tyre is for
limited use, however, if the tread
wear solid-band indicator appears,
replace the tyre with the same type of
temporary spare (page 6-48 ).
Replacing a Wheel
WARNING
Always use wheels of the correct size
on your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident.
.B[EB@&'&&"@&EJUJPOJOEC







6–49
Maintenance and Care
Owner Maintenance
CAUTION
A wrong-sized wheel may adversely
affect:
 
 Tyre fi t 
 Wheel and bearing life 
 Ground clearance 
 Snow-chain clearance 
 Speedometer calibration 
 Headlight aim 
 Bumper height 
 Tyre Pressure Monitoring System
When replacing a wheel, make sure the
new one is the same as the original factory
wheel in diameter, rim width, and offset
(inset/outset).
Proper tyre balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tyres can cause
vibration and uneven wear, such as
cupping and fl at spots.
.B[EB@&'&&"@&EJUJPOJOEC







6–50
Maintenance and Care
Owner Maintenance
Light Bulbs
Saloon HatchbackWith Xenon Fusion Headlights
With Halogen Headlights
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–51
Maintenance and Care
Owner Maintenance
Headlights (Low/High beam)
Running lights
Headlights (Low beam)
Headlights (High beam)/Running lights *
Front fog lights *
Front direction indicator lights
Position lights
Side direction indicator lights
Brake lights (With xenon fusion headlights)
Tail lights (With xenon fusion headlights)
Brake lights/Tail lights (With halogen headlights)
Rear direction indicator lights
Tail lights (With xenon fusion headlights)
Reverse lights
Rear fog light *
Reverse light (Left-hand drive model)
Reverse light (Right-hand drive model)
Rear fog light *1 /Reverse light *2 (Left-hand drive model)
Rear fog light *1 /Reverse light *2 (Right-hand drive model)
High-mount brake light
Number plate lights
Overhead lights (Front)/Map lights
Vanity mirror lights *
Overhead lights (Rear) *
Boot light (Saloon)
Luggage compartment light (Hatchback)
*1 With rear fog light
*2 Without rear fog light
.B[EB@&'&&"@&EJUJPOJOEC







6–52
Maintenance and Care
Owner Maintenance
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer when the replacement is
necessary.
Never touch the glass portion of a
halogen bulb with your bare hands
and always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurised gas. If one is broken, it will
explode and serious injuries could be
caused by the fl ying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
NOTE
  To replace the bulb, contact an
expert repairer, we recommend an
Authorised Mazda Repairer.
  If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
  Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
Replacing Exterior Light Bulbs
Headlights (With xenon fusion
headlights)
Low/High beam bulbs
You cannot replace the low/high beam
bulbs by yourself. The bulbs must
be replaced at an expert repairer, we
recommend an Authorised Mazda
Repairer.
Headlights (With halogen headlights)
Low-beam bulbs
1. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right, and turn
off engine.
2. Make sure the headlight switch is off.
.B[EB@&'&&"@&EJUJPOJOEC







6–53
Maintenance and Care
Owner Maintenance
3. Pull the centre of each plastic retainer
and remove the retainers.
Removal
Installation
4. Turn the screw anticlockwise and
remove it, and then partially peel back
the mudguard.
5. Disconnect the connector from the unit
by pressing the tab on the connector
with your fi nger and pulling the
connector downward.
6. Turn the socket and bulb assembly
to remove it. Carefully remove the
bulb from its socket in the refl ector by
gently pulling it straight backward out
of the socket.
7. Install the new bulb in the reverse order
of the removal procedure.
High-beam bulbs (With running lights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the bonnet.
.B[EB@&'&&"@&EJUJPOJOEC







6–54
Maintenance and Care
Owner Maintenance
3. Turn the cover anticlockwise and
remove it.
4. Turn the socket and bulb assembly
anticlockwise and remove it.
5. Install the new bulb in the reverse order
of the removal procedure.
High-beam bulbs (Without running
lights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the bonnet. 3. Disconnect the connector from the unit
by pressing the tab on the connector
with your fi nger and pulling the
connector downward.
4. Turn the socket and bulb assembly
to remove it. Carefully remove the
bulb from its socket in the refl ector by
gently pulling it straight backward out
of the socket.
5. Install the new bulb in the reverse order
of the removal procedure.
.B[EB@&'&&"@&EJUJPOJOEC