wheel MAZDA MODEL 3 HATCHBACK 2015 (in English) Manual Online

7–19
If Trouble Arises
Flat Tyre
2. Mount the spare tyre.
3. Install the wheel nuts with the bevelled
edge inward; tighten them by hand.
WARNING
Do not apply oil or grease to wheel
nuts and bolts and do not tighten the
wheel nuts beyond the recommended
tightening torque:
Applying oil or grease to wheel nuts
and bolts is dangerous. The wheel nuts
could loosen while driving and cause
the tyre to come off, resulting in an
accident. In addition, wheel nuts and
bolts could be damaged if tightened
more than necessary. 4. Turn the wheel brace anticlockwise and
lower the vehicle. Use the wheel brace
to tighten the nuts in the order shown.
If you are unsure of how tight the nuts
should be, have them inspected at an
expert repairer, we recommend an
Authorised Mazda Repairer.
Nut tightening torque
N·m (kgf·m, ft·lbf) 108—147
(12—14, 80—108)
.B[EB@&'&&"@&EJUJPOJOEC







7–20
If Trouble Arises
Flat Tyre
WARNING
Always securely and correctly tighten
the wheel nuts:
Improperly or loosely tightened wheel
nuts are dangerous. The wheel could
wobble or come off. This could result
in loss of vehicle control and cause a
serious accident.
Be sure to reinstall the same nuts you
removed or replace them with metric
nuts of the same confi guration:
Because the wheel studs and wheel
nuts on your Mazda have metric
threads, using a non-metric nut is
dangerous. On a metric stud, it would
not secure the wheel and would
damage the stud, which could cause the
wheel to slip off and cause an accident.
5. Remove the tyre blocks and store the
tools and jack.
6. Store the damaged tyre in the luggage
compartment.
7. Check the infl ation pressure. Refer to
Tyres on page 9-13 .
8. Have the fl at tyre repaired or replaced
as soon as possible.
NOTE
Do not press the tyre pressure
monitoring system set switch after
installing the spare tyre. The switch
is only to be pressed after installing
the repaired fl at tyre or installing a
replacement tyre (page 4-40 ).
WARNING
Do not drive with any tyres that have
incorrect air pressure:
Driving on tyres with incorrect air
pressure is dangerous. Tyres with
incorrect pressure could affect
handling and result in an accident.
When you check the regular tyres' air
pressure, check the spare tyre, too.
NOTE
To prevent the jack and tool from
rattling, store them properly.
.B[EB@&'&&"@&EJUJPOJOEC







7–23
If Trouble Arises
Battery Runs Out
1. Remove the battery cover.
2. Make sure the booster battery is 12
V and that its negative terminal is
grounded.
3. If the booster battery is in another
vehicle, do not allow both vehicles
to touch. Turn off the engine of the
vehicle with the booster battery and
all unnecessary electrical loads in both
vehicles.
4. Connect the jumper leads in the exact
sequence as in the illustration.
 

 
 Connect one end of a lead to the
positive terminal on the discharged
battery (1).
 

 
 Attach the other end to the positive
terminal on the booster battery (2).
 

 
 Connect one end of the other lead to
the negative terminal of the booster
battery (3).
 

 
 Connect the other end to the ground
point indicated in the illustration away
from the discharged battery (4).
5. Start the engine of the booster vehicle
and run it a few minutes. Then start the
engine of the other vehicle. 6. (With i-ELOOP system)
The i-ELOOP indicator light may fl ash
after the engine is started. The indicator
light turns off when the engine is
running and the charging is completed.
Make sure the i-ELOOP indicator light
is turns off before driving.
NOTE
  If the vehicle is driven with the
i-ELOOP indicator light fl ashing, a
beep sound is heard.
  If the steering wheel is operated with
the i-ELOOP indicator light fl ashing,
it may feel heavier than normal,
however, this does not indicate a
malfunction. The steering operation
will return to normal when the
i-ELOOP indicator light turns off.
  Do not remove the jumper leads
while the i-ELOOP indicator light is
fl ashing.
7. When fi nished, carefully disconnect the
leads in the reverse order described in
the illustration.
8. If the battery cover has been removed,
install it in the reverse order of
removal.
NOTE
Verify that the covers are securely
installed.
.B[EB@&'&&"@&EJUJPOJOEC







7–28
If Trouble Arises
Emergency Towing
Towing Description
We recommend that towing be done only
by an expert repairer, we recommend
an Authorised Mazda Repairer or a
commercial tow-truck service.
Proper lifting and towing are necessary
to prevent damage to the vehicle.
Government and local laws must be
followed.
A towed vehicle usually should have its
drive wheels (front wheels) off the ground.
If excessive damage or other conditions
prevent this, use wheel dollies.
Wheel dollies
When towing with the rear wheels on the
ground, release the parking brake.
CAUTION
  Do not tow the vehicle pointed
backward with driving wheels on
the ground. This may cause internal
damage to the transaxle.
  Do not tow with sling-type
equipment. This could damage your
vehicle. Use wheel-lift or fl atbed
equipment.
If towing service is not available in an
emergency, the vehicle may be towed with
all four wheels on the ground using the
towing hook at the front of the vehicle.
Only tow the vehicle on paved surfaces for
short distances at low speeds.
.B[EB@&'&&"@&EJUJPOJOEC







7–29
If Trouble Arises
Emergency Towing
CAUTION
Follow these instructions when towing
the vehicle with all wheels on the
ground.
 
 Shift to neutral (Manual transaxle),
or the N position (Automatic
transaxle).
  Switch the ignition to ACC. 
 Release the parking brake.
Remember that power assist for the
brakes and steering will not be available
when the engine is not running.
Towing Hooks
CAUTION
  The towing eyelet should be used
in an emergency (to get the vehicle
out of a ditch or a snow bank, for
example).
  When using the towing eyelets,
always pull the lead or chain in a
straight direction with respect to the
eyelet. Never apply a sideways force.
NOTE
When towing with chain or lead, wrap
the chain or lead with a soft cloth near
the bumper to prevent damage to the
bumper.
.B[EB@&'&&"@&EJUJPOJOEC







7–30
If Trouble Arises
Emergency Towing
Towing Hooks
1. Remove the towing eyelet and
the wheel brace from the luggage
compartment (page 7-3 ).
2. Wrap a fl athead screwdriver or similar
tool with a soft cloth to prevent damage
to a painted bumper, and open the cap
located on the front or rear bumper.
Front
Rear
CAUTION
Do not use excessive force as it may
damage the cap or scratch the painted
bumper surface.
NOTE
Remove the cap completely and store it
so as not to lose it.
3. Securely install the towing eyelet using
the wheel brace or equivalent.
Consult an Authorised Mazda Dealer.
Front
Wheel brace
Towing eyelet
Rear
Wheel brace
Towing eyelet
4. Hook the towing rope to the towing
eyelet.
.B[EB@&'&&"@&EJUJPOJOEC







7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Electronic Brake Force
Distribution System
Warning If the electronic brake force distribution control unit determines that some components
are operating incorrectly, the control unit may illuminate the brake system warning
light and the ABS warning light simultaneously. The problem is likely to be the
electronic brake force distribution system.
WARNING
Do not drive with both the ABS warning light and brake warning light
illuminated. Have the vehicle towed to an expert repairer, we recommend an
Authorised Mazda Repairer to have the brakes inspected as soon as possible:
Driving when the brake system warning light and ABS warning light are
illuminated simultaneously is dangerous.
When both lights are illuminated, the rear wheels could lock more quickly in an
emergency stop than under normal circumstances.
Charging System
Warning Light If the warning light illuminates while driving, it indicates a malfunction of the
alternator or of the charging system.
Drive to the side of the road and park off the right-of-way. Consult an expert repairer,
we recommend an Authorised Mazda Repairer. CAUTION
Do not continue driving when the charging system warning light is illuminated
because the engine could stop unexpectedly.
.B[EB@&'&&"@&EJUJPOJOEC







7–35
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Power Steering
Malfunction Indicator
Light The light illuminates/fl ashes if the electric power steering has a malfunction.
If the light illuminates/fl ashes, stop the vehicle in a safe place and do not operate the
steering wheel. There is no problem if the light turns off after a while. Contact an
expert repairer, we recommend an Authorised Mazda Repairer if the light illuminates/
fl ashes continuously.
NOTE
If the indicator light illuminates/fl ashes, the power steering will not operate
normally. If this happens, the steering wheel can still be operated, however, the
operation may feel heavy compared to normal, or the steering wheel could vibrate
when turning.
Repeatedly jerking the steering wheel left and right while the vehicle is stopped
or moving extremely slowly will cause the power steering system to go into
protective mode which will make the steering feel heavy, but this does not
indicate a problem. If this occurs, park the vehicle safely and wait several minutes
for the system to return to normal.
Contact Authorised Mazda Repairer and Have Vehicle Inspected
If any of the following warning lights turns on/fl ashes, the system may have a malfunction.
Contact an expert repairer, we recommend an Authorised Mazda Repairer to have your
vehicle inspected.
Signal Warning
Master Warning
Light
(Vehicles with type C/type D audio)
The light turns on when the system has a malfunction.
Operate the centre display and verify the content.
Refer to If a Warning Light Turns On or Flashes on page 7-32 .
(Vehicles without type C/type D audio)
The light illuminates continuously if any one of the following occurs. Consult an expert
repairer, we recommend an Authorised Mazda Repairer.
There is a malfunction in the battery management system. There is a malfunction in the brake switch.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–39
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
(Amber)
(Flashing)
Lane Departure
Warning System
(LDWS) Warning
Light
*
The warning light fl ashes when the system has a malfunction. Have your vehicle inspected
at an expert repairer, we recommend an Authorised Mazda Repairer.
The LDWS does not operate when the warning light fl ashes.
CAUTION
If any of the following cases occurs, the system may have a malfunction. Have the
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light fl ashes while the vehicle is being driven. The light does not illuminate when the ignition is switched ON. Always use tyres for all wheels that are of the specifi ed size, and the same
manufacture, brand, and tread pattern. In addition, do not use tyres with signifi cantly
different wear patterns on the same vehicle. If such improper tyres are used, the
LDWS may not operate normally.
When an emergency spare tyre is used, the system may not operate normally.
Headlight
Auto-Levelling
Malfunction
Indicator Light
*
This indicator light stays on for a few seconds when the ignition is switched ON.
Thereafter, the indicator light will illuminate when the headlight auto-levelling system has
a malfunction.
If the indicator light illuminates, contact an expert repairer, we recommend an Authorised
Mazda Repairer.
NOTE
Vehicles with the adaptive front lighting system (AFS) are not equipped with the
headlight auto-levelling malfunction indicator light. If there is a malfunction with the
headlight auto-levelling function, the AFS OFF indicator light fl ashes.
(Amber)
High Beam Control
System (HBC)
Warning Light
*
When illuminated
The warning light illuminates if the area of the windscreen in front of the forward sensing
camera (FSC) is fogged or obstructed.
When fl ashing
This light fl ashes if there is a malfunction in the high beam control system (HBC). Have
your vehicle inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
(Amber)
(Flashing)
Mazda Radar
Cruise Control
(MRCC) Warning
Light
*
The warning light fl ashes if there is a malfunction in the system while the Mazda Radar
Cruise Control (MRCC) system is on. Have your vehicle inspected at an expert repairer, we
recommend an Authorised Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC







7–46
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
If the warning light turns on/fl ashes simultaneously or a symbol is indicated in the display,
check the information regarding the warning light or symbol. (page 4-40 )
Display Content Action to be taken
Indicated when the push button start
is pressed while the shift lever is not
in the P position. Shift the shift lever to the P position.
Indicated when a seat belt is
unfastened and the driver's door is
opened while the i-stop function is
operating. Press the push button start again to start
the engine. For automatic transmission
vehicles, shift the shift lever to the P
position before starting the engine.)
Indicated when the push button start
is pressed without depressing the
brake pedal. Depress the brake pedal and press the
push button start.
Indicated when the push button start
is pressed without depressing the
clutch pedal. Depress the clutch pedal and press the
push button start.
Indicated while the steering wheel
is locked. Release the steering lock.
.B[EB@&'&&"@&EJUJPOJOEC