turn signal MAZDA MODEL 5 2007 User Guide

Black plate (152,1)
Select the proper setting from the following chart.Front seat Rear
seat Load Switch
Position
Driver Passenger
× ――― 0
×× ――0
×× × ―1
×× ×× 2
× ―― ×3
×: Yes
― :No
qDaytime Running Lights (Canada)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.
NOTE
The Daytime Running Lights turn off when the
parking brake is applied.
Turn and Lane-Change
Signals
q Turn Signal
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Right turn
Left turn OFF
Right lane
change
Left lane
change
Green indicators on the dashboard show
which signal is working.
Lane-change signals
Move the lever slightly toward the
direction of the change ―until the
indicator flashes ―and hold it there. It
will return to the off position when
released.
NOTE
If an indicator light stays on without flashing
or if it flashes abnormally, one of the turn
signal bulbs may be burned out.
5-46
Driving Your Mazda
Switches and Controls
Mazda5_8X91-EA-07E_Edition1 Page152
Tuesday, June 26 2007 8:47 PM
Form No.8X91-EA-07E

Black plate (159,1)
Hazard Warning Flasher
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning flasher and all
the turn signals will flash.
NOTE
lThe turn signals don't work when the
hazard warning lights are on.
lCheck local regulations about the use of
hazard warning lights while the vehicle is
being towed. They may forbid it.
Driving Your Mazda
Switches and Controls
5-53
Mazda5_8X91-EA-07E_Edition1 Page159
Tuesday, June 26 2007 8:47 PM
Form No.8X91-EA-07E

Black plate (188,1)
qOperating the Radio
Channel
preset
buttons
Auto
memory
button
Electric serial number
Scan button Seek tuning buttons Manual tuning dial
Satellite button
Band selector button
Radio ON
Press a band selector button (
)to
turn the radio on.
Band selection
Successively pressing the band selector
button (
) switches the bands as
follows: FM1 →FM2 →AM.
The selected mode will be indicated. If
FM stereo is being received, “ST ”will be
displayed.
NOTE
If the FM broadcast signal becomes weak,
reception automatically changes from
STEREO to MONO for reduced noise, and the
“ ST ”indicator will go out.
Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
NOTE
If the power supply is interrupted (fuse blows
or the battery is disconnected), the preset
channels will be canceled.
Manual tuning
Turning the manual tuning dial will
change the frequency higher or lower.
Seek tuning
Pressing the seek tuning button (
,)
will cause the tuner to seek a higher or
lower frequency automatically.
6-28
Interior Comfort
Audio System
Mazda5_8X91-EA-07E_Edition1 Page188
Tuesday, June 26 2007 8:47 PM
Form No.8X91-EA-07E

Black plate (196,1)
qOperating the In-Dash CD Changerí
Disc up
button Disc down
button Fast-forward
buttonTrack down
button
Random button
Scan button
Channel
preset
buttons
Track up button
Load button
Repeat button
CD slot
CD eject button
CD play button
Reverse button
(Music CD player)
(Music CD/MP3 CD player)
There are two types of In-dash CD
changers. Check which In-dash CD
changer type you own.
Type
Playable data
Music CD player · Music data (CD-DA)
Music CD/MP3 CD
player · Music data (CD-DA)
· MP3 file
NOTE
If a disc has both music data (CD-DA) and
MP3 files, playback of the two file types differs
depending on how the disc was recorded.
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed.
NOTE
The CD will begin playback automatically
after insertion.
A CD cannot be inserted while the display
reads
“WAIT ”. A beeping sound can be heard
during this waiting time. Simultaneously
pressing the power/volume dial and the load
button (
) for about 2 seconds will turn
this beeping sound ON or OFF.
6-36
Interior Comfort
íSome models.
Audio System
Mazda5_8X91-EA-07E_Edition1 Page196
Tuesday, June 26 2007 8:47 PM
Form No.8X91-EA-07E

Black plate (220,1)
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning flasher and all
the turn signals will flash.
NOTE
lThe turn signals don't work when the
hazard warning lights are on.
lCheck local regulations about the use of
hazard warning lights while the vehicle is
being towed. They may forbid it.
7-2
In Case of an Emergency
Parking in an Emergency
Mazda5_8X91-EA-07E_Edition1 Page220
Tuesday, June 26 2007 8:47 PM
Form No.8X91-EA-07E

Black plate (225,1)
Changing a Flat Tire
NOTE
If the following occurs while driving, it could
indicate a flat tire.
lSteering becomes difficult.lThe vehicle begins to vibrate excessively.lThe vehicle pulls in one direction.
If you have a flat tire, drive slowly to a
level spot that is well off the road and out
of the way of traffic to change the tire.
Stopping in traffic or on the shoulder of a
busy road is dangerous.
WARNING
Be sure to follow the directions for
changing a tire, and never get under a
vehicle that is supported only by a jack:Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
Never allow anyone inside a vehicle
supported by a jack: Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.
CAUTION
(With Tire Pressure Monitoring
System)
The wheels equipped on your Mazda
are specially designed for installation
of the tire pressure sensors. Do not
use non-genuine wheels, otherwise it
may not be possible to install the tire
pressure sensors. NOTE
lMake sure the jack is well lubricated before
using it.
(With Tire Pressure Monitoring System)
lBe sure to register the tire pressure sensor
ID signal code whenever tires or wheels are
changed (page 5-25).
1. Park on a level surface off the right-of- way and firmly set the parking brake.
2. Put a vehicle with an automatic transaxle in Park (P), a manual
transaxle in Reverse (R) or 1, and turn
off the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle and away from the vehicle and traffic.
5. Remove the jack, tool, and spare tire (page 7-3).
6. Block the wheel diagonally opposite the flat tire. When blocking a wheel,
place a tire block both in front and
behind the tire.
NOTE
When blocking a tire, use rocks or wood blocks
of sufficient size to hold the tire in place.
In Case of an Emergency
Flat Tire
7-7
Mazda5_8X91-EA-07E_Edition1 Page225
Tuesday, June 26 2007 8:47 PM
Form No.8X91-EA-07E

Black plate (278,1)
Light Bulbs
Some models.
Front fog lights
Luggage compartment light
Front turn signal lights/
Side-marker lights
Headlights (High-beam) Headlights (Low-beam)
Overhead light/Map lights (Front)
Side turn signal lights
Overhead light (Rear)
Reverse lights
High-mount brake light
License plate lights Brake lights/Taillights Rear turn signal lights
8-36
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page278
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (282,1)
Front turn signal lights/Side-marker
lights
1. Turn the center section of the plasticretainers counterclockwise and remove
them, then partially peel back the
mudguard.
Removal
Installation
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Remove the bulb by pushing it in slightly and turning it
counterclockwise.
4. Install the new bulb in the reverse orderof removal.
Side turn signal lights
1. Slide the unit as shown in the figure toremove it. 2. Disconnect the electrical connector
from the unit.
3. Install the new side turn signal unit in
the reverse order of removal.
NOTE
Bulb replacement is not possible because it is
built into the unit. Replace the unit.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights
1. Wrap a flathead screwdriver with a soft cloth to prevent damage to the rear
combination component and gently
insert it in the cover as shown in the
figure, and then remove the cover.
2. Remove the screws with a Phillipsscrewdriver and remove the rear
combination component.
8-40
Maintenance and Care
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page282
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (283,1)
3. Turn the socket and bulb assemblycounterclockwise and remove it.
4. Disconnect the bulb from the socket.
Reverse lights
Rear turn signal lights
Brake lights/Taillights
5. Install the new bulb in the reverse order of removal.
License plate lights
1. Remove the liftgate cover.
2. Pull the socket and bulb assembly andremove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front)
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
2. Turn the socket and bulb assemblycounterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-41
Mazda5_8X91-EA-07E_Edition1 Page283
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E

Black plate (288,1)
DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
15 EHPAS 80 A EHPAS
16 FOG 15 A Front fog lights
í
17 D.LOCK 20 A Power door lock
18 P.WIND
H/CLEAN 20 A
―
19 MAG 10 A Magnet clutch
20 DEFOG 25 A Rear window defroster
21 ENG+B 10 A PCM
22 STOP 10 A Brake lights
23 FUEL 20 A Fuel pump
24 HAZARD 10 A Turn signals, Hazard warning flashers
25 ROOM 15 AOverhead lights, Map lights, Luggage compartment light, For
protection of various circuits
26 ―― ―
27 ―― ―
28 GLOW SIG 7.5 A ―
29 HEAD HR 10 A Headlight high beam (RH)
30 HEAD HL 10 A Headlight high beam (LH)
31 HORN 15 A Horn
32 SUN ROOF 20 A Moonroof
í
33 ETC MIRROR
BURGLAR 7.5 A PCM
34 HEAD LR 15 A Headlight low beam (RH), Manual headlight leveling
í
35 HEAD LL 15 A Headlight low beam (LH)
36 ENG BAR2 15 A PCM
37 ENG BAR 15 A Air flow sensor, Engine control system
38 INJ 20 A Injector
39 ILLUMI 10 A Illumination
40 TAIL 10 A Taillights, Parking lights, License plate lights, For protection of
various circuits
8-46
Maintenance and Care
íSome models.
Owner Maintenance
Mazda5_8X91-EA-07E_Edition1 Page288
Tuesday, June 26 2007 8:48 PM
Form No.8X91-EA-07E