MAZDA MODEL 626 2002 Owners Manual

8-35
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Yo u r v e h i c l e’s electrical system is
protected by fuses.
If any lights, accessories, or controls don ’t
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.





Fuse Replacement
If the electrical system doesn ’t work, first
inspect fuses on the driver ’s side.
1. Turn off the ignition switch and other switches.
2. Open the fuse panel cover.
3. Pull the fuse straight out . 4. Inspect it and replace if it
’s blown.
5. Push in a new fuse of the same rating, and make sure it fits tightly. If it
doesn ’t, have an Authorized Mazda
Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the RADIO circuit.
Fuses
Fuse panel cover
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Normal Blown
CAUTION
J94S.book Page 35 Saturday, June 23, 2001 1:04 PM

8-36
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
If the headlights or other electrical
components don’t work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new one of the same rating . When replacing the 100A fuse:
1. Turn off the ignition switch.
2. Remove the negative battery terminal.
3. Remove the A nuts.
4. Lift the fuse block and remove the B
bolts.
5. Replace the fuse with a new one of the
same rating .
6. Install in the reverse order of removal.
Fuse block cover
Normal Blown
B
A
A
A
B
B BA
100A fuse
J94S.book Page 36 Saturday, June 23, 2001 1:04 PM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
1EGI INJ 30A Fuel injection
system
2 DEFOG 40A Rear window
defroster
3 —— —
4 MAIN 100A For protection of
all circuits
5 IG KEY 30A RADIO,
SUNROOF,
TURN, METER, ENGINE,
POWER
WINDOW,
WIPER fuses,
Ignition system
6 HEATER 40A Heater, Air
conditionerDESCRIPTION FUSE
RATING PROTECTED
COMPONENT
7 BTN 40A TAIL, STOP,
ROOM, DOOR LOCK,
HAZARD,
POWER SEAT fuses
8 COOLING
FA N 30A Cooling fan
9 AD FAN 30A Additional fan
10 (ABS) 60A Antilock brake
system
11 TAIL 15A Taillights,
Parking lights, Dashboard
illumination,
License plate
lights, Switches illumination
12 HORN 15A Horn
J94S.book Page 37 Saturday, June 23, 2001 1:04 PM

8-38
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
DESCRIPTIONFUSE
RATING PROTECTED
COMPONENT
13 (ABS) 20A Antilock brake
system
14 —— —
15 —— —
16 H/L-L 15A Headlight (Left)
17 H/L-R 15A Headlight
(Right)
18 (ABS) 20A Antilock brake
system
J94S.book Page 38 Saturday, June 23, 2001 1:04 PM

8-39
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Fuse panel (Driver’s side)
DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
1 AUDIO 15A Audio system
2 ROOM 15A Interior lights,
Trunk light
3 S.ROOF 15A Sunroof
4 METER 10A Gauges, Reverse
lights
5 D.LOCK 30A Power door lock
6 HAZARD 15A Hazard warning
lights
7A/B&ABS 10A Air bag system,
Antilock brake system
8 —— —
9 A/C 10A Air conditioner
10 —— —
11 TURN 10A Turn signals
12 WIPER 20A Windshield
wipers and washer
13 P.WIND 30A Power windows
14 —— —DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
15 RADIO 15A Audio system,
Socket, Outside mirror
16 ENGINE 10A Engine control
system
17 ILLUMI 10A Taillights,
License plate
lights, Parking
lights, Dashboard illumination
18 STOP 15A Brake lights,
Horn, Cruise control
19 CIGAR 15A Accessory
socket, Clock,
Radio, Outside mirror
20 —— —
21 —— —
22 P.SEAT 30A Power seat
23 M.DEF 15A Mirror defroster
24 P.POINT 15A Power point
J94S.book Page 39 Saturday, June 23, 2001 1:04 PM

8-40
Maintenance and Care
Form No. 8Q50-EA-01G
Appearance Care
The paintwork on your Mazda represents
the latest technical developments in
composition and methods of application.
Environmental hazards, however, can
harm the paint’s protective properties, if
proper care is not taken.
Here are some examples of possible
damage, with tips on how to prevent them.





Etching Caused by Acid Rain or
Industrial Fallout
Occurrence
Industrial pollutants and vehicle
emissions drift into the air and mix with
rain or dew to form acids. These acids can
settle on a vehicle ’s finish. As the water
evaporates, the acid becomes concentrated
and can damage the finish.
And the longer the acid remains on the
surface, the greater the chance is for
damage.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you suspect that acid rain has settled on
your vehicle ’s finish.





Damage Caused by Bird
Dropping, Insects, or Tree Sap
Occurrence
Bird droppings contain acids. If these
aren ’t removed they can eat away the clear
and color base coat of the vehicle ’s
paintwork.
When insects stick to the paint surface
and decompose, corrosive compounds
form. These can erode the clear and color
base coat of the vehicle ’s paintwork if
they are not removed.
Tree sap will harden and adhere
permanently to the paint finish. If you
scratch the sap off while it is hard, some
vehicle paint could come off with it.
Prevention
It is necessary to have your Mazda
washed and waxed to preserve its finish
according to the instructions in this
section. This should be done as soon as
possible.
Bird droppings can be removed with a
soft sponge and water. If you are traveling
and these are not available, a moistened
tissue may also take care of the problem.
The cleaned area should be waxed
according to the instructions in this
section.
Insects and tree sap are best removed with
a soft sponge and water or a commercially
available chemical cleaner.
Another method is to cover the affected
area with dampened newspaper for one to
two hours. After removing the newspaper,
rinse off the loosened debris with water.
How to Minimize
Environmental Paint
Damage
J94S.book Page 40 Saturday, June 23, 2001 1:04 PM

8-41
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G





Water Marks
Occurrence
Rain, fog, dew, and even tap water can
contain harmful minerals such as salt and
lime. If moisture containing these
minerals settles on the vehicle and
evaporates, the minerals will concentrate
and harden to form white rings. The rings
can damage your vehicle ’s finish.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you find water marks on your vehicle ’s
finish.





Paint Chipping
Occurrence
Paint chipping occurs when gravel thrown
in the air by another vehicle’ s tires hits
your vehicle.
How to avoid paint chipping
Keeping a safe distance between you and
the vehicle ahead reduces the chances of
having your paint chipped by flying
gravel.
NOTE
• The paint chipping zone varies with
the speed of the vehicle. For
example, when traveling at 90 km/h
(56 mph), the paint chipping zone is
50 m (164 ft).
• In low temperatures a vehicle ’s
finish hardens. This increases the
chance of paint chipping.
• Chipped paint can lead to rust
forming on your Mazda. Before this
happens, repair the damage by using
Mazda touch-up paint according to
the instructions in this section.
Failure to repair the affected area
could lead to serious rusting and
expensive repairs.
J94S.book Page 41 Saturday, June 23, 2001 1:04 PM

8-42
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G
Follow all label and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.





Maintaining the Finish
Was hi n g
To help protect the finish from rust and
deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface
when:
• The vehicle is washed without first
rinsing off dirt and other foreign
matter.
• The vehicle is washed with a rough,
dry, or dirty cloth.
• The vehicle is washed at a car wash
that uses brushes that are dirty or too
stiff.
• Cleansers or wax containing abrasives
are used. To minimize scratches on the vehicle
’s
paint finish:
• Rinse off any dirt or other foreign
matter using lukewarm or cold water
before washing.
• Use plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
• Rub gently when washing or drying the
vehicle.
• Take your vehicle only to a car wash
that keeps its brushes well maintained.
• Don ’t use abrasive cleansers or wax
that contain abrasives.
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the wings, and make sure
the drain holes in the lower edges of the
doors and rocker panels are clean.
Exterior Care
NOTE
• Mazda is not responsible for
scratches caused by automatic car
washes or improper washing.
• Scratches are more noticeable on
vehicles with darker paint finishes.
•Don ’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or
anodized aluminum parts. This may
damage the protective coating; also,
cleaners and detergents may
discolor or deteriorate the paint.
• To prevent damaging the antenna,
retract it before entering a car wash
facility or passing beneath a low
overhead clearance.
CAUTION
J94S.book Page 42 Saturday, June 23, 2001 1:04 PM

8-43
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives. Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for metallic, mica, and solid colors. 3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.





Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.





Bright-Metal Maintenance
• Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
• To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
• During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn ’t need it.
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
CAUTION
J94S.book Page 43 Saturday, June 23, 2001 1:04 PM

8-44
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G





Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also to
do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.





Aluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
Don
’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may result in
damage to the protective coating and
cause discoloration or paint
deterioration.
CAUTION
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
NOTE
• Don ’t use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
• Only use a mild soap or neutral
detergent and always use a sponge
or soft cloth to clean the wheels.
Rinse thoroughly with lukewarm or
cold water. Also, be sure to clean
the wheels after driving on dusty or
salted roads. This helps prevent
corrosion.
• Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
• If your aluminum wheels lose
luster, wax the wheels.
WARNING
J94S.book Page 44 Saturday, June 23, 2001 1:04 PM