MAZDA MODEL 626 2002 Owners Manual
Manufacturer: MAZDA, Model Year: 2002, Model line: MODEL 626, Model: MAZDA MODEL 626 2002Pages: 250, PDF Size: 4.83 MB
Page 181 of 250
8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q50-EA-01G
Schedule 2
I : Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.) R: Replace
L : Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
*2: If the vehicle is operated in cold districts { below –18 degrees C (0 degrees F) }, replace the timing belt at 96,000km (60,000miles).
Maintenance
Interval
Maintenance
Item Number of months or kilometers (miles), whichever comes first Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 Km 8 1624324048566472808896
(×1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60)
Engine valve clearance I
Drive belts (tension) II
Engine timing belt
*2Inspect at 96,000km (60,000miles)
Replace every 168,000km (105,000miles)
Engine oil Puerto Rico
Replace every 5,000km (3,000miles) or 3 months
others RRRRRRRRRRRR
Engine oil filter RRRRRRRRRRRR
Cooling system II
Engine coolant Replace at first 168,000km (105,000miles) or 60 months ;
after that, every 48,000km (30,000miles) or 24 months
Engine coolant level IIIIIIIIIIII
Idle speed II
Air filter I
*1RI *1R
Fuel lines and hoses*1II
Hoses and tubes for emission*1I
Spark plugs 2.0-liter engine
(non-PLATINUM tipped type)
RR
2.5-liter engine
(PLATINUM tipped type) Replace every 96,000km (60,000miles)
Function of all lights IIIIIIIIIIII
Brake lines, hoses and connections II
Brake and clutch fluid level IIIIIIIIIIII
Disc brakes IIII
Drum brakes II
Tire inflation pressure and tire wear IIIIIIIIIIII
Steering operation and linkages II
Power steering fluid level IIIIIIIIIIII
Front suspension ball joints II
Driveshaft dust boots II
Bolts and nuts on chassis and body IIII
Exhaust system heat shields II
All locks and hinges LLLLLLLLLLLL
08.fm Page 5 Monday, June 25, 2001 5:12 PM
Page 182 of 250
8-6
Maintenance and Care
Scheduled Maintenance
Form No. 8Q50-EA-01G
I: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.) R: Replace
L : Lubricate
Maintenance
Interval
Maintenance
Item Number of months or kilometers (miles), whichever comes first Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 Km 8 1624324048566472808896
(×1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60)
Wa s h e r f l u i d l e ve l IIIIIIIIIIII
Refrigerant amount (if installed) IIII
Compressor operation (if installed) IIII
08.fm Page 6 Monday, June 25, 2001 5:12 PM
Page 183 of 250
8-7
Maintenance and Care
Form No. 8Q50-EA-01G
Owner Maintenance
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.
When Refueling
• Brake and clutch fluid level (page 8-15)
• Engine coolant level (page 8-13)
• Engine oil level (page 8-11)
• Washer fluid level (page 8-20)
At Least Monthly
• Tire inflation pressures (page 8-26)
At Least Twice a Year (For Example, Every Spring and Fall)
• Automatic transaxle fluid level (page 8-18)
• Power steering fluid level (page 8-17)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
• Air filter (page 8-21)
• Engine coolant (page 8-13)
• Engine oil (page 8-11)
Owner Maintenance Schedule
J94S.book Page 7 Saturday, June 23, 2001 1:04 PM
Page 184 of 250
8-8
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Improper or incomplete service may result in problems. This section gives instructions
only for items easy to perform.
As explained in the Introduction (page 8-2), several procedure can be done only by a
qualified service technician with special tools.
Improper owner maintenance during the warranty period may affect warranty coverage.
For details, read the separate Mazda Warranty statement provided with the vehicle. If
you’re unsure about any servicing or maintenance procedure, have it done by an
Authorized Mazda Dealer.
There are strict environmental laws regarding the disposal of waste oil and fluids. Please
dispose of your waste carefully and with due regard to the environment.
We recommend that you entrust the oil and fluid changes of your vehicle to an Authorized
Mazda Dealer.
Owner Maintenance Precautions
Maintenance Procedures:Performing maintenance work on a vehicle is dangerous if not done properly. You can
be seriously injured while performing some maintenance procedure. If you lack
sufficient knowledge and experience or the proper tools and equipment to do the
work, have it done by a qualified technician.
Running the Engine:
Working under the hood with the engine running is dangerous. It becomes even more
dangerous when you wear jewelry or loose clothing.
Either can become entangled in moving parts and result in injury.
Therefore, if you must run the engine while working under the hood, make certain
that you remove all jewelry (especially rings, bracelets, watches, and necklaces) and
all neckties, scarves, and similar loose clothing before getting near the engine or
cooling fan.
Electrical Fan and Engine Inspection:
Inspecting the engine with the ignition switch in the ON position is dangerous. The
cooling fan could come on unexpectedly even when the engine isn ’t running. You
could be seriously injured by the fan. Turn the ignition switch off and remove the key
from the ignition switch when you inspect the engine.
WARNING
J94S.book Page 8 Saturday, June 23, 2001 1:04 PM
Page 185 of 250
8-9
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Engine Compartment Overview
2.0-liter engineAutomatic transaxle fluid-level
dipstick (only for automatic
transaxle)
Brake/Clutch fluid reservoir
Battery Fuse block
Engine coolant
reservoirAir filter
Cooling system cap Engine oil-filler cap
Power steering fluid
reservoir
Windshield washer
fluid reservoir Engine oil dipstick
2.5-liter engine
Air filter
Cooling system cap
Engine coolant reservoir
Power steering fluid
reservoir
Battery
Fuse block
Automatic transaxle fluid-level
dipstick (only for automatic
transaxle)
Brake/Clutch fluid reservoir
Engine oil-filler cap
Windshield washer
fluid reservoir Engine oil dipstick
J94S.book Page 9 Saturday, June 23, 2001 1:04 PM
Page 186 of 250
8-10
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Recommended Oil
Oil container labels provide important
information.
The quality designation SG, SH, SJ, SL,
or ILSAC must be on the label.
Engine oil viscosity, or thickness, has an
effect on fuel economy and cold-weather
operation (starting and oil flow).
Low-viscosity engine oils can provide
improved fuel economy and cold-weather
performance.
But high-temperature weather conditions
require higher-viscosity engine oils for
satisfactory lubrication. When choosing an oil, consider the
temperature range your vehicle will
operate in before the next oil change.
Then select the recommended viscosity
from this chart.
Energy conserving oils are recommended.
A chief contribution they make to fuel
economy is reducing the amount of fuel
necessary to overcome engine friction.
Engine Oil
SAEFORGASOLINEENGINES10W-30
(ILSAC)
–30 –20 –100 1020304050
–20 0 20 40 60 80 100 120
5W-30
10W-30
Using oils of viscosity besides those
recommended for specific temperature
ranges could result in engine damage.
CAUTION
J94S.book Page 10 Saturday, June 23, 2001 1:04 PM
Page 187 of 250
8-11
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal operating temperature.
3. Turn it off and wait 5 minutes for the oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and reinsert it fully.
5. Pull it out again and examine the level. It’s OK between L and F.
But if it’ s near at or below L, add
enough oil to bring the level to F. 6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.
The distance between L and F on the
dipstick represents the following:
Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly —protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Full
Low OK
2.0-liter engine
2.5-liter engine
Full
LowOK
Don
’t add engine oil over F. This may
cause engine damage.
L (US qt, Imp qt) 1.0 (1.06, 0.88)
Handling Used Engine Oil:Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
CAUTION
WARNING
J94S.book Page 11 Saturday, June 23, 2001 1:04 PM
Page 188 of 250
8-12
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Changing engine oil
1. Warm up the engine for a few minutes and turn it off. Remove the oil-filler
cap.
2. Remove the drain plug and drain the oil into a suitable container. 3. Replace the plug tightly after the oil
has thoroughly drained.
4. Fill the engine with new oil to the F mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the drain plug for leaks.
7. Turn it off and wait 5 minutes for the oil to return to the oil pan.
Check the oil level and fill to the F mark if
necessary.
Oil capacity (General reference only,
refer to Specifications section for
capacities.)
Changing oil filter
Because you need a special tool to
retighten the filter, an Authorized Mazda
Dealer should do the work.
Checking or Changing Engine Oil:Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don ’t check or
change the engine oil when the
engine is hot.
WARNING
2.0-liter engine
Loosen Tighten
Oil-filler cap
Drain plug
Oil-filler cap
Loosen Tighten
Drain plug
2.5-liter engine
NOTE
•
The indicated engine oil capacities
are for general reference purposes
only. When adding or changing oil,
verify the engine oil level with the
oil dipstick.
• Use only specified engine oil (page
10-4).
J94S.book Page 12 Saturday, June 23, 2001 1:04 PM
Page 189 of 250
8-13
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Inspecting Coolant Level
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year —at the beginning of the
winter season—and before traveling
where temperatures may drop below
freezing.
Inspect the condition and connections of
all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.
The coolant should be at full in the
radiator and between the F and L marks
on the coolant reservoir when the engine
is cool. If it
’s at or near L, add enough coolant to
the coolant reservoir to provide freezing
and corrosion protection and to bring the
level to F.
Do not overfill.
If new coolant is required frequently,
consult an Authorized Mazda Dealer.
Changing Coolant
Change coolant according to Scheduled
Maintenance (page 8-3).
Engine Coolant
Hot Engine:A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Don ’t
inspect the coolant system or add
coolant when the engine is hot.
WARNING
2.0-liter engine
2.5-liter engine
Radiator coolant will damage paint.
Rinse it off quickly.
• Use only soft (demineralized) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant ’s effectiveness.
• Don ’t add only water. Always add a
proper coolant mixture.
• The engine has aluminum parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
• DO NOT USE alcohol or methanol
antifreeze. DO NOT MIX alcohol
or methanol with the coolant. This
could damage the cooling system.
• Don ’t use a solution that contains
more than 60 % antifreeze.
This would reduce effectiveness.
CAUTION
CAUTION
J94S.book Page 13 Saturday, June 23, 2001 1:04 PM
Page 190 of 250
8-14
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
For mixture percentage:
To change coolant1. Remove the cooling system cap.
2. Only when the engine is cool, loosen the radiator drain plug and drain the
coolant into a suitable container.
3. With the drain plug loose but not fully removed, flush out the system with
running water.
4. Drain the system completely and retighten the plug.
Protection Volume
Antifreeze solution Wa t e r
Above −16 °C
(3 °F) 35% 65%
Above −26 °C
( − 15 °F) 45 55
Above −40 °C
( − 40 °F) 55 45
Removing the Cooling System Cap:Removing the cooling system cap or
drain plug while the engine is
running or hot is dangerous. This
might lead to cooling system and
engine damage and could result in
serious injury from escaping hot
coolant or steam. Turn off the engine
and wait until it
’s cool. Even then, be
very careful when removing the cap
or drain plug. Wrap a thick cloth
around it and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you ’re sure all the pressure is
gone, press down on the cap — still
using a cloth — turn the cap, and
remove it.
WARNING
2.0-liter engine Cooling system cap
Loosen
Tighten
Drain plug
Loosen
Tighten
LoosenTighten
Cooling system cap
Drain plug
2.5-
liter engine
Loosen Tighten
J94S.book Page 14 Saturday, June 23, 2001 1:04 PM