MAZDA MODEL CX-3 2015 Owners Manual (in English)

*Some models.4–151
When Driving
i-ACTIVSENSE
Radar Sensor (Front) *
Your vehicle is equipped with a radar sensor (front).
The following systems also use the radar sensor (front).
 


 Mazda Radar Cruise Control (MRCC)



 Distance Recognition Support System (DRSS)



 Smart Brake Support (SBS)
The radar sensor (front) functions by detecting the radio waves refl ected off a vehicle ahead
or an obstruction sent from the radar sensor.
The radar sensor (front) is mounted behind the front emblem.
Radar sensor (front)
If the Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Light (amber)
is illuminated, the area around the radar sensor may be dirty. Refer to “Warning Guidance”
in the centre display (Type C/D audio).
Refer to If a Warning Light Turns On or Flashes on page 7-35 .
$9@&;&&%@&EJUJPOJOEC







4–152
When Driving
i-ACTIVSENSE
CAUTION
Heed the following precautions to assure correct operation of each system.
 
 Do not adhere stickers (including transparent stickers) to the surface of the radiator
grille and front emblem in and around the radar sensor (front), and do not replace
the radiator grille and front emblem with any product that is not a genuine product
designed for use with the radar sensor (front).
  The radar sensor (front) includes a function for detecting soiling of the radar sensor's
front surface and informing the driver, however, depending on the conditions, it may
require time to detect or it may not detect plastic shopping bags, ice or snow. If this
occurs, the system may not operate correctly, therefore always keep the radar sensor
(front) clean.
  Do not install a grille guard. 
 If the front part of the vehicle has been damaged in a vehicle accident, the position of
the radar sensor (front) may have moved. Stop the system immediately and always
have the vehicle inspected at an Authorised Mazda Repairer.
  Do not use the front bumper to push other vehicles or obstructions such as when
pulling out of a parking space. Otherwise, the radar sensor (front) could be hit and its
position deviated.
  Do not remove, disassemble, or modify the radar sensor (front). 
 For repairs, replacement or paint work around the radar sensor (front), consult an
Authorised Mazda Repairer.
  Do not modify the suspension. If the suspension are modifi ed, the vehicle's posture
could change and the radar sensor (front) may not be able to correctly detect a vehicle
ahead or an obstruction.
$9@&;&&%@&EJUJPOJOEC







4–153
When Driving
i-ACTIVSENSE
NOTE
  Under the following conditions,
the radar sensor (front) may not
be able to detect vehicles ahead
or obstructions correctly and each
system may not operate normally.
 


 The rear surface of a vehicle
ahead does not refl ect radio waves
effectively, such as an unloaded
trailer or an automobile with a
loading platform covered by a
soft top, vehicles with a hard
plastic tailgate, and round-shaped
vehicles.
 


 Vehicles ahead with low vehicle
height and thus less area for
refl ecting radio waves.




 Visibility is reduced due to a
vehicle ahead casting off water,
snow, or sand from its tyres and
onto your windscreen.
 


 The luggage compartment is
loaded with heavy objects or the
rear passenger seats are occupied.
 


 Ice, snow, or soiling is on the front
surface of the front emblem.
 


 During inclement weather such as
rain, snow, or sand storms.
 


 When driving near facilities or
objects emitting strong radio
waves.
NOTE
  Under the following conditions,
the radar sensor (front) may not
be able to detect vehicles ahead or
obstructions.
 


 The beginning and end of a curve.



 Roads with continuous curves.



 Narrow lane roads due to road
construction or lane closures.
 


 The vehicle ahead enters the radar
sensor's blind spot.
 


 The vehicle ahead is running
abnormally due to accident or
vehicle damage.
 


 Roads with repeated up and down
slopes
 


 Driving on poor roads or unpaved
roads.
 


 The distance between your vehicle
and the vehicle ahead is extremely
short.
 


 A vehicle suddenly comes close
such as by cutting into the lane.


 To prevent incorrect operation of
the system, use tyres of the same
specifi ed size, manufacturer, brand,
and tread pattern on all four wheels.
In addition, do not use tyres with
signifi cantly different wear patterns
or tyre pressures on the same vehicle
(Including the temporary spare tyre).
  If the battery power is weak, the
system may not operate correctly.
  When driving on roads with little
traffi c and few vehicles ahead or
obstructions for the radar sensor to
detect, Smart Brake Support/Smart
City Brake Support (SBS/SCBS)
Warning Light (amber) temporarily
illuminates, however, this does not
indicate a problem.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–154
When Driving
i-ACTIVSENSE
Laser Sensor (Front) *
Your vehicle is equipped with a laser sensor (front). The laser sensor (front) is positioned
near the rearview mirror and used by the following systems.
 


 Smart Brake Support (SBS)



 Smart City Brake Support (SCBS)
Laser sensor (front)
CAUTION
Heed the following precautions to assure correct operation of the system.


 Keep the windscreen clean at all times. 
 Do not apply stickers to the surface of the windscreen (including transparent stickers). 
 If cracks or damage caused by fl ying gravel or debris is visible near the laser sensor
(front), stop using the system immediately and have your vehicle inspected by an
Authorised Mazda Repairer.
 See the next page on how to turn off the system. Refer to Personalisation Features on
page 9-13 .
  Do not apply a coating agent to the windscreen. 
 When replacing the windscreen wipers or windscreen, consult an Authorised Mazda
Repairer.
  Never remove the sensor. 
 A removed sensor will not meet the conditions for a class 1M laser under the IEC
60825-1 specifi cation and therefore eye safety cannot be assured.

 Do not peer into the sensor using optical instruments with a magnifi cation function
such as magnifying glasses, and microscopic and objective lenses within a distance of
100 mm (3.94 in) from the sensor.
$9@&;&&%@&EJUJPOJOEC







4–155
When Driving
i-ACTIVSENSE
Laser sensor radiation data
Maximum average power:45 mW
Pulse duration:33 ns
Wavelength:905 nm
Divergence angle (horizontal×vertical):28 degrees×12 degrees
NOTE
  In the following cases, the laser sensor (front) cannot detect vehicles ahead correctly,
and each system may be unable to operate normally.
 


 The windscreen is dirty.



 Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front).
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 
 If there are recognizable cracks or damage caused by fl ying gravel or debris on the
windscreen, always have the windscreen replaced. Consult an Authorised Mazda
Repairer for replacement.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–156
When Driving
i-ACTIVSENSE
Radar Sensors (Rear) *
Your vehicle is equipped with radar sensors (rear). The following systems also use the radar
sensors (rear).
 


 Blind Spot Monitoring system (BSM)



 Rear Cross Traffi c Alert (RCTA)
The radar sensors (rear) function by detecting the radio waves refl ected off a vehicle
approaching from the rear or an obstruction sent from the radar sensor.
Radar sensors (rear)
The radar sensors (rear) are installed inside the rear bumper, one each on the left and right
sides.
Always keep the surface of the rear bumper near the radar sensors (rear) clean so that the
radar sensors (rear) operate normally. Also, do not apply items such as stickers.

3FGFS
UP
&YUFSJPS
$BSF
PO
QBHF



CAUTION
If the rear bumper receives a severe impact, the system may no longer operate normally.
Stop the system immediately and have the vehicle inspected at an Authorised Mazda
Dealer.
$9@&;&&%@&EJUJPOJOEC







4–157
When Driving
i-ACTIVSENSE
NOTE
  The detection ability of the radar sensors (rear) has limitations. In the following cases,
the detection ability may lower and the system may not operate normally.
 


 The rear bumper near the radar sensors (rear) has become deformed.



 Snow, ice or mud adheres to the radar sensors (rear) on the rear bumper.



 Under bad weather conditions such as rain, snow and fog. 

 Under the following conditions, the radar sensors (rear) cannot detect target objects or
it may be diffi cult to detect them.




 Stationary objects on a road or a road side such as small, two-wheeled vehicles,
bicycles, pedestrians, animals, and shopping carts.
 


 Vehicle shapes which do not refl ect radar waves well such as empty trailers with a
low vehicle height and sports cars.
 
 Vehicles are shipped with the direction of the radar sensors (rear) adjusted for each
vehicle to a loaded vehicle condition so that the radar sensors (rear) detect approaching
vehicles correctly. If the direction of the radar sensors (rear) has deviated for some
reason, have the vehicle inspected at an Authorised Mazda Dealer.
  For repairs or replacement of the radar sensors (rear), or bumper repairs, paintwork,
and replacement near the radar sensors, consult an Authorised Mazda Dealer.
  Turn off the system while pulling a trailer or while an accessory such as a bicycle
carrier is installed to the rear of the vehicle. Otherwise, the radio waves emitted by the
radar will be blocked causing the system to not operate normally.
  The radar sensors are regulated by the relevant radio wave laws of the country in
which the vehicle is driven. If the vehicle is driven abroad, authorization from the
country in which the vehicle is driven may be required.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–158
When Driving
Cruise Control
Cruise Control *
With cruise control, you can set and automatically maintain any speed of more than about
25 km/h (16 mph).
WARNING
Do not use the cruise control under the following conditions:
Using the cruise control under the following conditions is dangerous and could result
in loss of vehicle control.
 
 Hilly terrain 
 Steep inclines 
 Heavy or unsteady traffi c 
 Slippery or winding roads 
 Similar restrictions that require inconsistent speed
Cruise Control Switch
OFF switch ON switch Without Adjustable Speed Limiter With Adjustable Speed LimiterON/OFF switch
CANCEL switch RESUME switch
SET+/SET- switch
CANCEL switch
RESUME switch
SET+/SET- switch
$9@&;&&%@&EJUJPOJOEC







4–159
When Driving
Cruise Control
Cruise Main Indicator Light
(Amber)/Cruise Set Indicator
Light (Green)
The indicator light has two colours.
Cruise Main Indicator Light (Amber)
The indicator light illuminates amber
when the cruise control system is
activated.
Cruise Set Indicator Light (Green)
The indicator light illuminates green when
a cruising speed has been set.
Activation/Deactivation
With adjustable speed limiter
To activate the system, press the ON/OFF
switch. The cruise main indicator light
(amber) illuminates.
To deactivate the system, press the switch
again.
The cruise main indicator light (amber)
turns off.
Without adjustable speed limiter
To activate the system, press the ON
switch. The cruise main indicator light
(amber) illuminates.
To deactivate the system, press the OFF
switch.
The cruise main indicator light (amber)
turns off.
WARNING
Always turn off the cruise control
system when it is not in use:
Leaving the cruise control system in an
activation-ready state while the cruise
control is not in use is dangerous as
the cruise control could unexpectedly
activate if the activation button is
accidentally pressed, and result in loss
of vehicle control and an accident.
NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the ignition
is switched OFF with the cruise control
system operable, the system will be
operable when the ignition is switched
ON the next time.
To Set Speed
1 . (With adjustable speed limiter)
Activate the cruise control system
by pressing the ON/OFF switch. The
cruise main indicator light (Amber)
illuminates.
(Without adjustable speed limiter)
Activate the cruise control system
by pressing the ON switch. The
cruise main indicator light (Amber)
illuminates.
2. Accelerate to the desired speed, which
must be more than 25 km/h (16 mph).
$9@&;&&%@&EJUJPOJOEC







4–160
When Driving
Cruise Control
3. Set the cruise control by pressing the
SET
or SET switch at the desired
speed. The cruise control is set at the
moment the SET
or SET switch is
pressed. Release the accelerator pedal
simultaneously. The cruise set indicator
light (Green) illuminates.
NOTE
  The cruise control speed setting
cannot be performed under the
following conditions:
 


(Automatic transaxle)
 The selector lever is in the P or N
position.
 


(Manual transaxle)
 The shift lever is in the neutral
position.
 


 The parking brake is applied.



(Vehicles with adjustable speed
limiter)
  The ON/OFF switch for the
adjustable speed limiter is pressed.


 Release the SET or SET switch
at the desired speed, otherwise the
speed will continue increasing while
the SET
switch is pressed and
held, and continue decreasing while
the SET
switch is pressed and held
(except when the accelerator pedal is
depressed).
  On a steep grade, the vehicle may
momentarily slow down while
ascending, or speed up while
descending.
NOTE
  Cruise control will cancel if the
vehicle speed decreases below
21 km/h (13 mph) when cruise is
activated, such as when climbing a
steep grade.
  Cruise control may cancel at about
15 km/h (9 mph) below the preset
speed (such as may happen when
climbing a long, steep grade).
To Increase Cruising Speed
Follow either of these procedures.
To increase speed using cruise control
switch
Press the SET
switch and hold it. Your
vehicle will accelerate. Release the switch
at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will increase the
preset speed according to the number of
times it is operated.
Increasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET
or
SET
switch and release it immediately.
$9@&;&&%@&EJUJPOJOEC